Tender For bid to ras supply of finolex or polycab or natural white or equivalent , pvc switch board snow white size 8 inch x 10 inch for main switches or db make havells or finolex or polycab or natural white or equivalent , pvc l bend and t junction joint for pvc casing and capping confirming to is 3419 part 3 make havells or finolex or polycab or natural white or equivalent , switch socket combination snow white multipurpose 2 in 1 of 15 amp 230 volts make havells or finolex or polycab or natural white or equivalent , switch socket combination snow white 5 amp 230 volts make anchor or ssk or cona , service bracket 40mm dia gi tubing medium grade 1.5 mtr long make jindal or tata orkalinga or equivalent , service cable pvc insulated aluminium conductor 1100 volt grade heavy duty served with inner sheathing of pvc tap and overall pvc sheathed in service connection 10 sqmm 2 core , ceiling rose three terminal snow white make anchor or ssk or cona or equivalent , led bulk head fitting high pressure die cast aluminum front cover with glass cover with specially design gasket with led lamp 10 watts , pvc flexible wire copper conductor multi stranded 0.0016 by 76 make havells or finolex or polycab or natural white or equivalent , pvc flexible conduit pipe 15 mm dia make havells or finolex or polycab or natural white or equivalent , pvc round or squire block make havells or finolex or polycab or natural white or equivalent , fire extinguisher of one kilogram capacity dry power type conforming to is-13849 along with its accessories , change over switch 32 amps 4 pole tpn , earthing plate 600 x 600 x 6 mm galvanised steel suitable for gi strip fittings drilled with 2 nos holes for 6 mm dia near one side. , ci earth pit cover of size 300 x 300 x 6 mm with angle iron of size 20x20mm 3 mm thick with ms frame. , funnel fitted with 20 mm diameter gi pipe 1.5 m long. pipe make jindal or tata or kalinga or equivalent , gi wire 4 mm diameter for earthing. , charcoal , salt normal , air termination single pointed aluminium rod 12 mm dia and 300 mm long. , testing point terminal block make of gun metal and phosphorus bronze size 75 x 75 x 25 mm drilled and screwed including 3 nos 8 mm dia 25 mm long hexagonal head screw , aluminium strips 25 x 3.0 mm , galvanized iron strip 32 x 6 mm , insulating pvc block 75x75x30 mm with insulating clamp nut and bolt make presto or polycab or finolex or equivalent , individual standalone plastic body smoke alarm with adequate provision for fixing on wall ceiling roof , individual standalone plastic body heat alarm with adequate provision for fixing on wall or ceiling or roof , fire ball extinguisher of 1.3 kg wt with suitable provision for wall mounting and capable of self activating on contact with flames , double sleeping bunk alongwith rexene sleeved matress of make kurlon or sleepwell or corform or equivalent complete all as specified in tech specification. , steel bed side locker of size 1000mm x 1520mm x 450mm comlete all as specified in tech specification , study chair of size length 56 cm height 82 cm and width 56cm type lacquered finish with arm sear and back cushion velvet uphostery , study table of size 4x2 wooden top on round tube structure with three drawers unit , looking mirror of selected quality frameless of size 600 x 450 x 5 mm make prayag or saint gobain or modiguard or equivalent , water dispenser of 230 v 500 watts without refrigerator with normal cold and heating capacity of 5 lts per hour with storage compartment and auto shut off facility , portable indoor type high quality kero heater metal body ignites type of continues heating //bid details 2 / 53 duration min 8 hrs and above with capacity 4 ltrs above min output 7000 btu per hrs incl all accessories , plastic dustbin of capacity 40 ltr make neelkamal or cello or supreme or equivalent
Tender For supply of dome valve spares d d - daetp:bronze bush set for dome shaft: part no:-: drg no:-nspcl/pp-2/o<(>&<)>m/ahs/1/part-1 <(>&<)> 2. product no: bronze bush , daetp:shaft set for 200 nb dome valve: part no:-: drg no:-nspcl/bmd/daetp/012 product no: shaft set for 200nb dome valve , daetp:discharge valve top adaptor: part no:-: drg no: 1. , nspcl/bmd/daetp/016 part-1 2. for inner side of top adaptor refer to to plate drawing. product no: discharge valve top adaptor , daetp: discharge valve bottom adaptor: part no:-: drg no:-nspcl/bmd/daetp/016-part-3 product no: discharge valve bottom adaptor , 200nb:cast iron dome for dome valve : part no:-: drg no:- nspcl/bmd /dome element/ci , 200 nb dome valve complete assembly: part no:-: drg no:-nspcl/bmd/daetp/015 , 200 nb discharge valve complete assembly: part no:-: drg no:-nspcl/bmd/daetp/016
Tender For quotation for rate of c/f pump (clear water) and its accessories at saraswatipur rwss - supplying ,installation and commissioning of multi stage/ horizontal split casing/multi stage centrifugal pump (make: kirloskar / wpil/jyoti/ mather & platt) rating-15 kw/20hp as per is:5120, capable for discharging 72 m3/hr against a head of 40 m , consisting of bronze impellers, stainless steel pump shaft, etc. with all accessories coupled with energy efficient (ie3) tefc squirrel cage induction motor confirming to is:325 and is:12615, having 15% more bhp than that of pump, operating on 1500rpm, 415v, 3 ph, 50 hz [make: kirloskar /abb/cgl/bhel] all complete with required size of sluice valve and cidf non- return valve standard fitting, strainers, reducer, foot valve, pressure gauge, nuts & bolts, packings, fitting & fixing, labour & technician, etc. all complete job as per site requirement and direction of e/i. discharging -72 m3/hr and head - 40m (1w + 1s) 20 hp, cost towards making new foundation base for pump -motor set and panel including providing new ms base plate as per sample suitable for 20 hp pump- motor set, cutting and welding where necessary, nuts, bolts, flange etc with all labour, tools and materials all complete job., cost towards making suitable suction line by suppling of ms pipe, bend, flange, nut, bolt rubber insertion, including making hole for suction, cutting, welding etc all complete., cost towards making suitable delivery line by suppling of ms pipe, bend, flange, nut, bolt rubber insertion including joining the new suction line to the existing header by means of cutting, welding etc all complete., providing , erecting and commissioning lt motor control panel board fabricated with ms sheet and painted, dust-vermin proof. floor mounted cubical panel board shall be consisting of proper power distribution 100 a copper busbar- 4 pole, 1 no. 100 a mccb as incoming feeder and 2 nos. 63a mccb as outgoing feeders for motors, 1 no. 63 a mccb as spare feeder (for motor), 2 no. 32a mcb for lighting and other loads. including selector switches, switch disconnector isolator, voltmeters, ampere meters, mfm, indicator lamps, internal wiring, danger board, protection units & relay, capacitor banks/apfc and 02 nos suitable fasd starter, etc. all complete and as per is and direction of e/i .), supplying and erecting 16 sqmm 3 core xlpe / pvc insulated, 1100 v grade un-armoured copper cable with isi mark stranded / solid copper conductor complete erected on wall / panel or in provided trench in an approved manner. (from panel to motors), providing and erecting chemical earthing with all required materials etc all complete., cost of 3t triple type chain pully block suitable as below with 6m lift complete with laoad chain and hand chain suitable for avove lift, tested 50% over load as per is 3832 carry isi etc. all complete job as per the site requirement and indian standard., cost towards dismanteling of old pump set and foundation and making arrangements for removal of debries from the pump house., construction of chamber for 100mm sluices valve.
Tender For quotation for rate of vt pump (raw water) and its accessories at saraswatipur rwss - supplying , installation and commissioning of single/multi stage vertical turbine pump sets (make: kirloskar /wpil/ mather & platt), rating-22kw/30hp approx as per is 1710, capable of discharging 94.56 m3/hr against a head of 50 m, consisting of bowl assemblies, bronze impellers, column assembly, stainless steel pump shaft, line shaft, etc. with all accessories coupled with squirrel cage induction motor confirming to is:325 and is:12615, having 20% more bhp than that of pump, operating on 1500rpm, 415v, 3 ph, 50 hz [make: kirloskar, jyoti, abb, cgl, bhel, jsl] all complete with required size of sluice valve and cidf non- return valve standard fitting, strainers, reducer, pressure gauge, etc. all complete job as per site requirement and direction of e/i. discharging -94.56 m3/hr and head - 50m (1w + 1s) 30 hp, cost towards making new foundation base for pump -motor set and panel including providing new ms base plate as per sample suitable for 30 hp pump- motor set, cutting and welding where necessary, nuts, bolts, flange etc with all labour, tools and materials all complete job for raw water vt pump set., cost towards jointing newly installed pump motor set to the existing header at raw water p/p., providing , erecting and commissioning lt motor control panel board fabricated with ms sheet and painted, dust-vermin proof. floor mounted cubical panel board shall be consisting of proper power distribution 160 a copper busbar- 4 pole, 1 no. 160 a mccb as incoming feeder and 2 nos. 100a mccb as outgoing feeders for motors, 1 no. 100 a mccb as spare feeder (for motor), 2 no. 32a mcb for lighting and other loads. including selector switches, switch disconnector isolator, voltmeters, ampere meters, mfm, indicator lamps, internal wiring, danger board, protection units & relay, capacitor banks/apfc and 02 nos suitable fasd starter, etc. all complete and as per is and direction of e/i ., supplying and erecting 16 sqmm 3 core xlpe / pvc insulated, 1100 v grade un-armoured copper cable with isi mark stranded / solid copper conductor complete erected on wall / panel or in provided trench in an approved manner. (from panel to motors)., providing and erecting chemical earthing with all required materials etc all complete., cost of 3t triple type chain pully block suitable as below with 6m lift complete with laoad chain and hand chain suitable for avove lift, tested 50% over load as per is 3832 carry isi etc. all complete job as per the site requirement and indian standard., cost towards dismantling of old pump set and foundation and making arrangements for removal of debries from the pump house.
Tender For quotation for rate of items of vt pump (raw water) and accessories at gumuria rwss - supplying , installation and commissioning of single/multi stage vertical turbine pump sets (make: kirloskar /wpil/ mather & platt), rating-7.5 hp approx as per is 1710, capable of discharging 24.5 m3/hr against a head of 30 m, consisting of bowl assemblies, bronze impellers, column assembly, stainless steel pump shaft, line shaft, etc. with all accessories coupled with squirrel cage induction motor confirming to is:325 and is:12615, having 20% more bhp than that of pump, operating on 1500rpm, 415v, 3 ph, 50 hz [make: kirloskar, jyoti, abb, cgl, bhel, jsl] all complete with required size of sluice valve and cidf non- return valve standard fitting, strainers, foot valve, reducer, pressure gauge, etc. all complete job as per site requirement and direction of e/i. discharging -24.5 m3/hr and head - 30m (1w + 1s) 7.5 hp, cost towards making new foundation base for pump -motor set and panel including providing new ms base plate as per sample suitable for 7.5 hp pump- motor set, cutting and welding where necessary, nuts, bolts, flange etc with all labour, tools and materials all complete job., cost towards jointing newly installed pump motor set to the existing header., providing , erecting and commissioning lt motor control panel board fabricated with ms sheet and painted, dust-vermin proof. floor mounted cubical panel board shall be consisting of proper power distribution 100 a copper busbar- 4 pole, 1 no. 100 a mccb as incoming feeder and 2 nos. 63 a mccb as outgoing feeders for motors, 1 no. 63 a mccb as spare feeder (for motor), 2 no. 32a mcb for lighting and other loads. including selector switches, switch disconnector isolator, voltmeters, ampere meters, phase indicator lamps, internal wiring, danger board, protection units & relay, capacitor banks/apfc and 02 nos suitable fasd starter, etc. all complete and as per is and direction of e/i .), supplying and erecting 6 sqmm xlpe / pvc insulated, 1100 v grade un-armoured copper cable with isi mark stranded / solid copper conductor complete erected on wall / panel or in provided trench in an approved manner. (from panel to motors)., providing and erecting chemical earthing with all required materials etc all complete., cost of 3t triple type chain pully block suitable as below with 6m lift complete with laoad chain and hand chain suitable for avove lift, tested 50% over load as per is 3832 carry isi etc. all complete job as per the site requirement and indian standard., cost towards dismanteling of old pump set and foundation and making arrangements for removal of debries from the pump house.
Tender For quotation for rate of items of c/f pump(clear water) and its accessories at gumuria rwss - supplying ,installation and commissioning of multi stage/ horizontal split casing/multi stage centrifugal pump (make: kirloskar / wpil/jyoti/ mather & platt) rating-40hp as per is:5120, capable for discharging 30 m3/hr against a head of 101 m , consisting of bronze impellers, stainless steel pump shaft, etc. with all accessories coupled with energy efficient (ie3) tefc squirrel cage induction motor confirming to is:325 and is:12615, having 15% more bhp than that of pump, operating on 1500rpm, 415v, 3 ph, 50 hz [make: kirloskar /abb/cgl/bhel] all complete with required size of sluice valve and cidf non- return valve standard fitting, strainers, reducer, foot valve, pressure gauge, ms delivery & suction pipe, common header, nuts & bolts, packings, fitting & fixing, labour & technician, etc. all complete job as per site requirement and direction of e/i. discharging -30 m3/hr and head - 101 m (1w + 1s) 40 hp, cost towards making new foundation base for pump -motor set and panel including providing new ms base plate as per sample suitable for 40 hp pump- motor set, cutting and welding where necessary, nuts, bolts, flange etc with all labour, tools and materials all complete job., cost towards making suitable suction line by suppling of ms pipe, bend, flange, nut, bolt rubber insertion, including making hole for suction, cutting, welding etc all complete., cost towards making suitable delivery line by suppling of ms pipe, bend, flange, nut, bolt rubber insertion including joining the new suction line to the existing header by means of cutting, welding etc all complete., providing , erecting and commissioning lt motor control panel board fabricated with ms sheet and painted, dust-vermin proof. floor mounted cubical panel board shall be consisting of proper power distribution 200 a copper busbar- 4 pole, 1 no. 160 a mccb as incoming feeder and 2 nos. 100 a mccb as outgoing feeders for motors, 1 no. 100 a mccb as spare feeder (for motor), 2 no. 32a mcb for lighting and other loads. including selector switches, switch disconnector isolator, voltmeters, ampere meters, mfm, indicator lamps, internal wiring, danger board, protection units & relay, capacitor banks/apfc and 02 nos suitable fasd starter, etc. all complete and as per is and direction of e/i ., supplying and erecting 25 sqmm xlpe / pvc insulated, 1100 v grade un-armoured copper cable with isi mark stranded / solid copper conductor complete erected on wall / panel or in provided trench in an approved manner. (from panel to motors)., providing and erecting chemical earthing with all required materials etc all complete., cost of 3t triple type chain pully block suitable as below with 6m lift complete with laoad chain and hand chain suitable for avove lift, tested 50% over load as per is 3832 carry isi etc. all complete job as per the site requirement and indian standard., cost towards dismanteling of old pump set and foundation and making arrangements for removal of debries from the pump house.
Tender For corrigendum : tender for supply of pump spares - rear cover v07 mc wcb , front cover v07 mc wcb , gasket rear cover v07 ptfe , gasket casing v96 ptfe , gasket sleeve v96 ptfe , gasket impeller v96 ptfe , mechanical seal cartridge id55 od 82 wl26.5 c/sic duplex vit , casing v96 mc nab , impeller v96 mc nab to nes 747 pt.2 , front wear ring v96 nab to nes 747 pt.2 , back wear ring v96 nab to nes 747 pt.2 , impeller nut v96 mc nab to nes 747 pt.2 , sleeve shaft v96 phosphor bronze , shaft v96 en57 , coupling guard v96 ss304 forming , spring washer m12 ss 316 , plain washer m10 ss316 , spring washer m8 ss 316 , bolt hex m10x1.5 35mm ss316 ft , circlip b110 spring steel , key parallel ss410 408 7 r r , double row angular contact ball bearing 3310-a-2z , lock nut ss m50x15 skf no km10 , lock washer ss id50 skf no mb10 , key ss410 70 10 8 rf , bolt allen m8x1.25x35 ss 316 , grease nipple 1 by 8 inch angled ss 316 , grease nipple 1 by 8 inch straight ss 316 , oil seal od65 x id45 x thk 8 viton , drain plug hex 1 , o ring id 44x3 nbr , key ss410 52 12 8 r r , stud m12x1.75x60l , stud m8x1.25x55l20tx20nss316 , disc coupling n55-230mm spacer , bearing deep groove ball 6310 2z c3 , impeller v07 mc nab , mechanical seal cartridge id 48 od74 wl24.6 c/sic duplex vit , shaft v07 en57 , bearing frame v07 mc wcb , front wear ring v07 mc nab , back wear ring v07 mc nab , gasket impeller w66 ptfe , impeller nut v07 mc nab , sleeve shaft v07 phosphor bronze , hex nut m8 ss 316 , squre head plug 14 bsp ss 316 , coupling spacer-140mm rrs-110 32mm pump end & 42mm motor end , stuffing box v07 mc nab , stuffing box v96 mc nab to nes 747 pt.2 , eye bolt m12x1.75 ms , motor bracket v96 45k motor ms , top mounting plate v96 45kw motor ms , hex nut m16 ss 316 , m12 washer ss 316 , plain washer m16 ss 316 , hex nut m6 ss 316 , bolt hex m16x2 80 mm ss 316 ft , bolt hex m16x2 110mm ss 316 ft , bolt hex m6 12mm ss 316ft , plain washer m6 ss316
Tender For supply of set of gauges consists of 1.gauge for side bearer wearing bronze piece - 2 nos 2.gauge for side bearer wearing plate thickness- 2nos 3.comb gauge for measuring fla nge thickness of bg wheels- 5nos 4.wheel diameter gauge fitted with vernier scale (mod el wd 1)- 2nos 5.gauge for measuring dash pot oil level( flexible wire gauge)- 4nos note: material required as per the attached specification & drawings [ warranty period: 30 months after t he date of delivery ]