Latest rotor scrap Tenders | Government rotor scrap Tenders

CTN :43681723

23 Feb, 2026 NA

Jammu - Jammu And Kashmir

Tender For bid to ras supply of machinary and equipments electrical engg c c -3- phase alternator , dcmotor , dc motor , transformer , variac , inductive , capacitive , current , potential , ujt , fan , speed , single , fully , verification , half , full , dc , tool , semiconductor , zener , fet , filter , transistor , push , hartley , r-c , r , clipper , phase , earth , meggerinsulation , trainer , fuse , autotransformer , differerential , mcb , under , solar , electrical , battery , frequency , wiring , swinburn , hydro , wind , cut , load , scr , triac , diac , coil , star , 3phase , universal , flip , power , ac ) /bid number: gem/2026/b/7115408 * /dated: 21-01-2026 & & / bid document1 / 60

CTN :43818787

23 Feb, 2026 NA

Jammu - Jammu And Kashmir

Tender For corrigendum : supply of engine tool kit , ring spanner set , combination spanner set , open end spanner set , screw driver set philips type , screw driver set slotted , dead blow hammer set , ballpein hammer , sledge hammer , oil drain pan , funnels , tool trolley , oil filter wrench belt typesets , oil filter chain typesets , oil filter wrenchsets , nut splitter rusted nut separator , cold chisel , lug wrench , wire brush , inspection led lamp , engine scanner , ac gas refilling recycling machine , spark plug cleaner and tester , hydraulic hand pallet truck , portable arc welding machine , hydraulic trolley jack , battery hydrometer , air blow gun , heat gun , battery tester , head light beam aligner , antilock braking system abs trainer , engine stand , screw jack mechanical , bench grinder , tire tread depth gauge digital , dial bore gauge , spark plug wrench or socket , demonstration board of working model of mpfi system , measuring tape , wheel chocks , cutaway of synchromesh gearbox , cutaway of automatic transmission , cut section model starter motor , cut section model super charger , cut section model turbo charger , transaxle cutaway , cutaway of catalytic converter , cutaway of muffler , cutaway of dual diaphragm tandem vacuum brake booster , cutaways of ignition coils , cutaway of a manual rack and pinion steering gear box , cut section model egr valve , cut section model of mock layout of car wiring vehicle body electrical system working comprehensive type , cut section model of both side macpherson suspension strut with drive shaft and disc brake , cut section model of lubrication system of a car , cut section model of cooling system of a car , cut section model of dpfdiesel particulate filter , digital thermometer industrial , electric solder irongun , digital multimeter , clamp meter , 12 v lead acid battery section , digital tyre inflator gun with pressure gauge , angle grinder , digital torque wrench , tachometer digital , battery charger , electric revit gun , bench vice , jumper cables , orbital sander , paintless dent repair kit , refractometer , manifold guage , speedometer cutaway , working car wiper cum washer mechanism , motorized car window mechanism , instruction board for air bag system , impact wrench pneumatic , hydraulic engine crane , creeper , portable drill hammer , working model of fluid fly wheel , vernier calliper , spray paint gun , chain block pulley , car washer , dent puller , tyre changer , injector tester and cleaner , wheel balancer , decarbonizing machine , nitrogen tyre inflator //bid details2 / 71

CTN :44135318

07 Mar, 2026 NA

Bardhaman - West Bengal

Tender For supply of nozzle torch type cutting , alarm audible visual type pre start warning , fixture lighting type outdoor voltage 110 v power 18w , switch type pull cord flame proof , torch cutting type gas fft , cable electrical voltage rating , regulator pressure type double stage fft foxygen , regulator pressure type da , flash back arrestor set , hose medium industrial oxygen , hose nonmetallic material rubber inside , fan pulley , motor pulley , planetory pinion70 teeth , pinion motor , life time gasket , splined shaft , main pinion sun gear 24teeth , spider assembly , flange compagnion 6c rear , coupling flange , bearing cup and cone , seal kit

CTN :44158480

28 Feb, 2026 2.24 Lacs

Kolkata - West Bengal

Tender For maintenance of electrical installation and fans compound lights i/c repair maintenance of motor pumping sets at general pool quarter complex at ic block, salt lake, kolkata-700106. ( sh- dismantling & repairing of centrifugal motor pump set along with required accessories & star delta starter & lifting of submersible pump set.)

CTN :44142026

02 Mar, 2026 NA

Meerut - Uttar Pradesh

Tender For supply of fog lamp with bulb 24v , door lock assy lh , assy door lock lh , pole isolator switch , oil filter , gasket cylinder head , regulator assy frt for window , hand primer , solenoid electrical , hose radiator outlet , flap rust 1400 x 20 , distributor assy hydraulic , camber air pressure brk , horn electrical , starter motor 12v , alternator with double , combination plier , bearing frt wheel , filter element oil

CTN :44150590

28 Feb, 2026 3.23 Lacs

Kozhikode - Kerala

Tender For annual plan-panangad gp- koorikkunnu dwss-installation of motor pump set-project no s0308/26 ,koorikkunnu dwss-installation of motor pump set -general electrical work

CTN :44150497

28 Feb, 2026 1.80 Lacs

Pathanamthitta - Kerala

Tender For konni bp-pr.no.s0179/26-konni bp aruvappulam gp ward 10 drinking water project pipe line extension motor and pump set errection-general electrical work

CTN :44150506

28 Feb, 2026 1.66 Lacs

Pathanamthitta - Kerala

Tender For konni bp- pr.no.s0180/26-konni gp kalanchira drinking water project pipe line extension motor and pump set errection-general electrical work

CTN :44156288

03 Mar, 2026 NA

Robertsganj - Uttar Pradesh

Tender For providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - iti campus; hvac, electrical system or installation, furniture, grass cutting door repairing and painting sewing machine electrical motor repairing computer maintenance;..

CTN :42286856

23 Feb, 2026 NA

Sibsagar - Assam

Tender For bid to ras corrigendum : supply of electrical engineering equipment d d - to study characteristics of dc generator , to study load test on dc shunt motor and plot the following characteristics of the motor with data acquisition system with software , to study load test on dc series motor , to study load test on dc compound motor , to obtain efficiency of a dc shunt machine using swinburns test and to obtain speed control of dc shunt motor using armature resistance control and field resistance control , to study single phase transformer setup , to study three phase squirrel cage induction motor setup with data acquisition system with software , to study single phase induction motor setup , to study dc shunt motor three phase ac generator setup , study parallel operation of three phase alternator using dark lamp method and bright lamp method and synchroscope and auto synchronization , test the performance of synchronous motor at different load condition to see the effect of variation of excitation and power factor likev and inverted v curve ) /bid number : gem/2025/b/6723896 * /dated: 14-10-2025 & & / bid document 1 / 17

Rotor Scrap Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors