Tender For supply of pre-fabricated steel tubular ffl 2 oblic 1 structure of size 2.40 x 2.40m , quick setting compound rapidite make acclerex cico fosroc , aggregate 20mm. stone aggregate to be crushed rock or gravel 20mm graded , aggregate 40mm. stone aggregate to be crushed rock or gravel 40mm graded , manufactured sand m sand confirming to is 383 2016 specifications for coarse and fine aggregates. , bricks cement pcc brick of size 230mm x 115mm x 75 mm with sharp corners , non skid ceramic tiles coloured 7 to 8 mm thick in floors , liquid water proofing compound is 2645 2003 , white cement packet 01 kg , pvc ceiling rose 2 obliq 3 terminal with pvc square box complete with screws , led tube light fitting 1 x 12 w 2 feet long complete with all accessories including led tube rod , pvc cable insulated and pvc sheathed 1.50 sq mm twin core with copper conductor , flexible wire pvc insulated twin core twisted of size 23 obliq 0.0076 with copper conductor , modular switch one way 6 amp 1 module , white cover plate with frame 2 module , white cover plate with frame 3 module , metal flush box 2 module , metal flush box 3 module , mcb double pole 230v ac 50 hz 16 amps 10ka confirming to is 8828 1996 , mcb distribution board in sheet metal enclosure two ways with blanks conforming to is 8828 1978 , ms screw 20 mm full threaded per pkt 100 nos conforming to is 723 1972 , tape insulation 2 cm width 10 mtr long isi marked , pvc casing caping 25 mm x 16mm , pvc casing caping square box 4 inch x 4 inch , pvc body exhaust fan 250mm sweep with lowers , vitreous china squatting pan orissa pattern size 580 x 440 mm white with integral foot rests , pvc valve less syphonic action type low level flushing cistern 10 ltrs capacity , 110mm dia upvc pipe 3 mtr long single socketed with cowl , 110mm dia upvc single tee , 110 x 110mm nahani trap with jali , 4 inch dia upvc bend , 15mm brass stop cock conforming to is-8934 1978 , 3 layer of pp r polypropylene random copolymer pipes sdr 7.4 , 20mm elbow suitable for 20mm dia ppr pipe conforming to is 1239 1989 , 20mm socket suitable for 20mm dia ppr pipes conforming to is 1239 1989 , 20mm equal tee suitable for 20mm dia ppr pipe conforming to is 1239 1989 , 20mm union suitable for 20mm ppr pipes conforming to is 12391989 , ppr end plug 20mm conforming to is 1239 1989 , ppr pipe clamp suitable for 20mm piping , bib cock 20 mm with flange conforming to is 8931 1978 , gi reducer socket 15 obliq 20mm , gi reducer elbow 15 obliq 20mm , pre fabricated man hole cover 6 feet x 4 feet made of isa 40x40x6mm frame , rotational moulded polyethylene water storage tank double layer , ppr tank connector 20mm with check nut and washer , white lead safeda , thread cotton ball 100 m long , vitreous china wash hand basin whb white flat back size 550x400 mm , 20mm dia pillar taps of ptmt of any colour high pressure screwed for iron pipe , 110mm dia upvc swr pipe single socketed pipe type a in any length with rubber joint , 600x450mm size looking mirror mounted on pvc with pvc shelf assembly including all fittings all as specified
Tender For supply of weld mesh panel with accessories , omega clamp , mushroom head bolt nut with washer , fence post , straining y arm for supporting top ptcc , accessories for fitting y arm , intermediate y arm for supporting top ptcc material , anchor rod , punched tape concertina coil , galvanised steel barbed wire isi marked a 5 designation for galvanised steel barbed wire , quick setting compound rapiditemake acclerex cico fosroc , aggregate 20mm. , aggregate 40mm. , ms binding wire annealed not less than 0. 9mm dia , natural sand conforming to is 383 1970 , portable welding machine , wire cutter 18 inch , aluminium ladder 9 steps , hand gloves leather 500 g , hand gloves canvas , hand gloves rubber , bold cutter 12 inch , y joint 10 feet long , y joint 12 feet long , hammer sledge 4lbs , steel gurmaia planer , plumbob and mason thread , cutting pliers 8 inch , shovel with wooden handle , hack saw frame , wooden gurmala , ratchet spanner single socket 14 sproket , trowel masson brick carandy , water level pipe 100 m , hack saw blade double ended , measuring tape 5 m , measuring tape 30 m , axis pick with wooden handle , iron cutting machine , drill machine complete set , drill bits complete set , ratchet spanner with deep socket 12 obliq 13 mm , welding rods , hog ring curd less rebar type gun machine battery operated typing wire dia meter 0. 8 to 1mm battery capacity 4400 mah , rivet gun machine , binding stick , tasla iron 18 inch , hdpe water storage tank 500 ltr , fawada with wooden handle , crow bar 5 feet long , bolt cutter 32 inch , wire cutter 150 mm , suction cum delivery pipe plastic 1 inch dia 200m long , iron cutting machine blade , alluminium straight edge 50mm sq 2 mm thick 1800mm long ) /bid number: gem/2026/b/7099633 * /dated: 11-01-2026 & & / bid document1 / 43
Tender For one panchayath one playground- thanniyam stadium in kallara grama panchayath in vamanapuram lac, thiruvananthapuram- supply and installation of outdoor gym and sports equipment - outdoor gym equipments, od252260/2025-2026 : horse rider - supply and installation of horse rider having the following specifications:dimensions: (l x w x h) 1140 x 400 x 1400 mm. main frame - 114 mm od b class gi pipe. foundationplate m.s. round plate of 250 mm & 8 mm thick. foundation cover cap - dome shape of pp / nylon /hdpe material. remaining frame is made by 48 mm od ?b? class gi pipe. seat frame ?is made by 48mm od ?b? class gi pipe. seat position must be horizontal to 110 -120 degree. link - made up of 48 mm od ?b? class g.i. pipe. angle between link and ground position is 10-20 degree. handle - 33 mm od ?b? class gi pipe. paddle vertical support - 60 mm od ?b? class gi pipe. handle frame- 42 mm od ?b? class gi pipe dually bending design. foot pipe - 33 mm od ?b? class gi pipe. support frame ? 10 mm thick ms flat is used. seat- dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material hdpe.bearing bush closing cap ? pp / nylon / hdpe material. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft.foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brand.bearing bushes - 60mm od seamless pipe. pin ? made of 25 mm m.s. bright bar. grips - high quality rubber 46 mm od. circlips ? a 24 circlips are used for assembly. coating - best quality of powder coating 60 to 70 micron. safety instructions and exercise chart - start &finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od252261/2025-2026 : back extension - supply and installation of back extension having the following specifications: dimensions: (l x w x h) 1060 x 730 x 990 mm. main frame - made from 88 mm od ?b?class g.i. pipe. foundation plate ? m.s. round plate of 250 mm & 8 mm thick. leg support - 42 mm od ?b? g.i pipe. seat rest pipe ? 42 mm od ?b? class g.i pipe. handle pipe ? 33 mm od ?b? class g.i pipe.footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 3 mm thick used to support it. footrest pipe ? 42 mm od ?b? class g.i pipe and 80 x 40 mm ms rectangular pipe. closing cap ?pp / nylon / hdpe material. seat ? 360 x 300 x 2 mm thick m.s. seat with corner fillet for safety. grips - high quality rubber 46 mm od. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od252262/2025-2026 : cross trainer (double) - supply and installation of double cross trainer having the following specifications: dimensions: (l x w x h) 2280 x 550 x 1650 mm. main frame- made of 88 mm od ?b? class gi pipe dually bending design. foundation plate ? m.s. round plate of 250 mm & 8 mm thick. paddle vertical support - 42 mm od ?b? class gi pipe. handle - 33 mm od ?b?class gi pipe dually bending design. leg movement frame ? 50 mm x 50 mm x 2 mm thick square pipe. footrest - cast iron 124 x296 x 5 mm thick and m.s. plat
Tender For construction of madakkathara grama panchayath stadium in ollur lac, thrissur- supply and installation of outdoor gym equipment - open gym equipment, od263824/2025-2026 : chest press (double) - supply and installation of double chest press having the following specifications: dimensions: (l x w x h) 1955 x 710 x 1900 mm. main center pipe - ø 114 mm od ?b? class gi pipe. foundation plate ?m.s. round plate of ø 250mm & 8 mm thick. foundations cover cap- dome shape of pp / nylon / hdpe material. remaining frame - made up of ø 48 mm od ?b? class g.i. pipe. handle - made up of ø48mm od ?b? class g.i. pipe. link - made up of ø 48 mm od ?b? class g.i. pipe. seat & back rest ? 380 x 275 x 60 mm thick high-density polyethylene (hdpe) blow molded with m10 integrated wall thickness 3 to 4 mm. bearing bush closing cap?s? pp / nylon / hdpe material. handle must be connected with frame by 8 mm laser cutting ms profile. top closing cap ? dome shape made by pp / nylon / hdpe material.foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brands. pin ? made up of ø 25 mm m.s. bright bar pin. bearing bushes - ø 60 mm od seamless pipe. grips - high quality rubber ø 46 mm od. circlips?a 24 circlips are used for assembly. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be min m20 cc and design shall be approved by the engineer-in -charge before installation.), od263826/2025-2026: air walker - supply and installation of air walker having the following specifications: dimensions: (l x w x h) 1190 x 380 x 1244 mm. main frame- ø 88 mm od "b" class gi pipe dually bending design.foundation plate- m.s. round plate of ø 250 mm & 8 mm thick. paddle ø 42 mm od round gi pipe. handle - ø 33 mm od "b" class gi pipe. footrest - cast iron 124 x 296 x 5 mm thick and m.s. plate of 2 mm thick use to support it. top closing cap dome shape made by pp / nylon / hdpe material. closing cap's - pp / nylon / hdpe material. bracket - 8 mm thick laser profile is used to support paddle frame. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing- use is 6005 permanent lubricated reputed brands. pin's ø 25mm m.s. bright bar pin. circlips- a 24 circlips are used for assembly. bearing bushes -ø 60 mm od seamless pipe. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be min m20 cc and design shall be approved by the engineer-in -charge before installation.), od263830/2025-2026 : leg press (double) - specifications: dimensions: (l x w x h) = 1676 x 400 x1500mm. main frame - ø 114 mm od “b” class gi pipe. foundation plate – m.s. round plate of ø 250 mm & 8 mm thick. foundations cover cap - dome shape of pp / nylon / hdpe material. link - is ø 60 mm od “b” class gi pipe. seat frame - ø 42 mm od “b” class gi pipe. leg press back rest should be angled in 120 - 130 degree. footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 2 mm thick use to support it. seat & back rest – 380 x 275 x 60 mm thick high- density polyethylene (hdpe) blow molded with m
Tender For work of installing sports equipment in various parks of murlipura, vidyadhar nagar and jhotwara zone. (arc) - double arch swing: in this two children can enjoy the swing at one time.the arch shaped side frame is made of 65mm nb b class gi pipe and top pipe is made up of 50mm nb b class g.i. pipe.the frame is powder coated to give an aesthetic look.the swing is made up of 5mm thick anti skid canvas top. the rubber belt seat is suspended on 6mm rubber coated gi chain. the ball bearings shall be mounted inside a specially designed nylon clamp., deluxeslide:deluxe slide chute is made from stainless steel (ss) of 304 grade swith 16 swg sheet.the structure comprises of 20 mm nb and 25 mm nb b class g.i. pipe. the centre support is made in 80 mm nb b class g.i. pipe and 15 mm nb g.i. pipe.the ladder cum railing is made up of 20 mm nb and 25 mm nb b class gi pipe. the platform is made up of 14 swga luminium sheet swith an tiskid for firm foot grip.there are train gular steps of 16 swg sheets. the chute has its end such as it causes safe landing of the child.the pipe sare powder coated to avoid rusting., frp wave slide :providing and fixing of frp wave slide its required area 4.6 mtr x 0.9 mtr platform height should be 5 ground level and should be made by 32 mm nb and 25 nb and 20 mm nb pipe ms pipe.slide length10 all components paint by pu paint in multi colours., doubleseesaw: providing and fixing of double see saw of height 0.5 mtr from ground level.seat frame and base should be made with 50 mm nb b class g.i. pipe. handle pipe should be 25 mm nb b class g.i.pipe.length of see saw lever should be 6 feet. seats are made with frp/lldpe. max. 4 children can play at one time., spiral slide : the chute of the spiral slide is made of frp (fibre reinforced plastic) having thickness of 4mm. slide centre support shall be 80mm nb b class gi pipe. landing module shall be supported by 20mm nb b class gi pipe. slide extension platform is made from frp(fibre reinforced plastic). the laddermain frame is 25 mm gi pipe.the railing shall be made from15 mm nb and 20 mm nb b class gi pipe. all pipes are powder coated to avoid rusting.
Tender For work of installing sports equipment in various parks of jagatpura and malviya nagar zone. (arc) - double arch swing: in this two children can enjoy the swing at one time.the arch shaped side frame is made of 65mm nb b class gi pipe and top pipe is made up of 50mm nb b class g.i. pipe.the frame is powder coated to give an aesthetic look.the swing is made up of 5mm thick anti skid canvas top. the rubber belt seat is suspended on 6mm rubber coated gi chain. the ball bearings shall be mounted inside a specially designed nylon clamp., deluxeslide:deluxe slide chute is made from stainless steel (ss) of 304 grade swith 16 swg sheet.the structure comprises of 20 mm nb and 25 mm nb b class g.i. pipe. the centre support is made in 80 mm nb b class g.i. pipe and 15 mm nb g.i. pipe.the ladder cum railing is made up of 20 mm nb and 25 mm nb b class gi pipe. the platform is made up of 14 swga luminium sheet swith an tiskid for firm foot grip.there are train gular steps of 16 swg sheets. the chute has its end such as it causes safe landing of the child.the pipe sare powder coated to avoid rusting., frp wave slide :providing and fixing of frp wave slide its required area 4.6 mtr x 0.9 mtr platform height should be 5 ground level and should be made by 32 mm nb and 25 nb and 20 mm nb pipe ms pipe.slide length10 all components paint by pu paint in multi colours., doubleseesaw: providing and fixing of double see saw of height 0.5 mtr from ground level.seat frame and base should be made with 50 mm nb b class g.i. pipe. handle pipe should be 25 mm nb b class g.i.pipe.length of see saw lever should be 6 feet. seats are made with frp/lldpe. max. 4 children can play at one time., spiral slide : the chute of the spiral slide is made of frp (fibre reinforced plastic) having thickness of 4mm. slide centre support shall be 80mm nb b class gi pipe. landing module shall be supported by 20mm nb b class gi pipe. slide extension platform is made from frp(fibre reinforced plastic). the laddermain frame is 25 mm gi pipe.the railing shall be made from15 mm nb and 20 mm nb b class gi pipe. all pipes are powder coated to avoid rusting.
Tender For bid to ras supply of do letter pad , table glass , big size tower coloured , table acrylic desk adjustable , notepad writing pad , organiser executive , dak stamp , side table , rubber stamp , name plate , record register 250 pages 100 gsm , name add on appointment board , table glass transperent , welcome crds , diary , tea cup set , serving tray , borosel glass set six no per set , water bottle hot and cold , electric kettle , micro wave oven , dustbin plastic , small tea spoon , normal tea spoon , qtr plates , hand towel , door curtain 6ft , window curtains , hand dryer , soap dispenser , bucket plastic , mug plastic , padlock 10 liver , sediment filter , pre carbon filter , prefilter externsl with pipe fitting , dress table ladies room , single mattress , pillow with cover , chair sofa , bed , bed sheet , blanket , foor mat , carom board size 48 each , chess board size 24 each , water jug , disposable garbage bag , extension socket with cable , induction stove , spiral ring , photo frame , portfolia , film fitting , gamla with plant and sand ) /bid number: gem/2025/b/6840767 * /dated: 18-12-2025 & & / bid document1 / 41
Tender For supply of cleat assembly suitable for 60 kva transformer having external frame dimension 100 mm x 100 mm x 51 mm (hxwxd) sealed with epdm rubber for lhb a.c. coaches including fitment in a.c. coaches, power car & pantry car as per rdso specification no: rdso/2008/el/spec/0067. rev-3 and per annexure attached with. material must be procured from clw approved sources or its authorised dealers. [ warranty period: 30 months after the date of delivery ]
Tender For supply of glass cleaning liquid spray , hygiene freshener pad for urinals , advanced ceramic and sanitary surface descaling solution , soft paper sheet dispenser for hygiene use , disposable rodent control adhesive mat , mop head mop replacement head refill , automatic wall mounted air freshener fragrance sprayer perfume dispenser , odour control fragrance refill unit , gel type room fragrance unit , multi purpose cleaner for glass surfaces , antibacterial hand cleaning solution , broad use surface hygiene solution , twin side toilet brush , paper based absorbent napkins , floor liquid for kitchen , customised coated wooden working platform board , floor squeegee plastic and foam long handle , premium acrylic directional door label ten by three inch with adhesive backing , personal hand safety wear rubber material , biodegradable material waste bag large size , biodegradable material waste bag small size , pots with plants customised , spin mop with steel wringer plastic bucket , multi tier wooden shoe organizer dark finish , multi purpose messenger utility bag , portable clothes drying support frame , double walled vacuum insulated flask , textile pressing support stand ) /bid number : gem/2026/b/7061866 * /dated: 09-01-2026 & & / bid document 1 / 24