Tender For supply of ferritic steelsheet 3x1250x2100mm., as per drawing: rdso spec. no. c-k201, grade x2crni12 (409m) table 1&2, heat treatment condition 2b as per table-5., packing instruction: stainlesssteelsheets, coils and plates:- (a) stainlesssteel (austenitic & ferritic steel) coils. the coil shall be protected in reasonably good condition to withstand normal handling hazard during transit with the following provision as the barest minimum: i) coil should be wrapped with a layer of water proof paper through out whole length. ii) coil should be wrapped with a layer of biodegradeable sheet. iii) outer & inner of coil should be wrapped with gi sheet. iv) side of the coil should be covered with card board sheet. v) after this whole coil should be wrapped with biodegradeable plastic sheet of suitable thickness. vi) the inner edge of the coil should be protected by gi ring followed by another iron ring. vii) outer edge of the coil should be wrapped with gi ring. viii) coil should be securely strapped with minium 5 steel bands through the eyes of the coil and minium 3 steel bands on the circumference of the eye. ix) whole coil should be mounted on wooden blocks for easy lifting/stacking. x) the sheets in coil form for thickness 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 1000-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of coil5.0 - 10 tonnes. (b) stainlesssteel (austenitic & ferritic steel plates/sheets) i) the sheets/plates shall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate shall be seprated with a layer of water proof paper, after this the whole bundle should be wrapped with double layer of water proof paper and a biodegradeable plastic sheet of suitable thickness. a metal protection in edges should also be provided. ii) all bundles shall have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop for every additional meter. the bundles shall also be provided with skid (wooden packing under neath) to facilitate handling. mechanical damange & corrosion during transit ifany shall be at the cost of supplier. [ warranty period: 30 months after the date of delivery ]
Tender For supply of length 30 cm , k wire 2.5mm length 30 cm , k wire 2.0 mm length 30 cm , kirschner wire 250 mm long by 2.0 mm dia, both ends trocar point , miniplate 2.0 x 6 hole titanium with gap , miniplate 2.0 x 6 hole titanium without gap , thermoplast ext nasal splint , threaded kirschner wire stainlesssteel 1.5mm dia , tissue expander crescent 340 ml , tissue expander crescent 250 ml , tissue expander oval 100 ml , tissue expander oval 250 ml , tissue expander oval 340 ml , tissue expander oval 500 ml , tissue expander oval 80 ml , tissue expander rectangular 340 ml , titan mini plate 4 hole with gap , titan mini screw 2 by 7 mm curiform head , titanium screws 11 mm , universal mini external stabilization system set complete, jess, for ctev large , universal mini external stabilization system set complete, jess, for ctev medium , universal mini external stabilization system set complete, jess, for ctev small , wire kirschner 15cm long by 1.5 mm dia both ends trocar point , wire kirschner 25cm long by 1.0 mm dia both ends trocar point , abdominal binder without perinial support assorted size , bandage-abdominal binder with perineal support - large , bandage- abdominal binder with perineal support - medium , finger extension splint tmt , flex finger splint , malleable splints upper limb disposable , mallet finger splint , splint nasal, 0.5 mm thick - aluminium , stax mallet finger splint , thumb spica splint assorted size , wrist hand resting splint cone , wrist hand resting splint finger , fibrin glue 1ml , multiple clip applier for open surgery with 20 preloaded small size titanium clips automatic loading with jaw angle of 30 degrees , bone wax box of 12 , clip applicator compatible with lt100 for open surgeries , clip applicator compatible with lt200 for open surgeries , clip applicator compatible with lt 300 for open surgeries , disposable fue hair trans motorized punches semi sharp size 1 mm , disposable fue hair trans motorized punches semi sharp size-1.2mm , disposable fue hair trans motorized punches semi sharp size-1mm , hair clipper , knotless biocomposite suture anchors 2.9 mm. , leur lock plastic syringe of 50ml capacity , lina single skin hook, small sharp lina medical , marking pen , multipe clip applier for open surgery with 20 preloaded small size titanium clips automatic loading with jaw angle of 30 degrees , ortho roll cast padding cotton size 10 cm x3 mtr , ortho roll cast padding cotton size 15 cm x3 mtr , ot pack large gamma irradiation sterilized , microvascular anastomotic coupler size 2.0 mm , microvascular anastomotic coupler size 2.5 mm , microvascular anastomotic coupler size 3.0 mm , kirschner wire 1.4mm with trocar tip, length 150mm , kirschner wire 1.8mm with trocar tip, length 150mm 0.5 percent chlorhexidine acetate tulle gauze dressing, 0.5 percent chlorhexidine acetate tulle gauze dressing , bovine collagen and glycosaminoglycan, canister gel with tubing to fit , diperoxochloric acid topical soln, distractors 6mm by 6mm, distractors 6mm by 8mm., dressing extra thin wound care, dressing collagen wound , dressing extra thin wound care, , fenastrated unique native collagen-elastin matrix,, fenstrated native collagen-elastin dermal, nanocrystalline silver dressing , silicon spray , silicon gel plus peptide plus ceramide , single knitted fiber glass pre padded splint, skin graft blades for humbys knife , sterile post op dressing pack large, sterile skin marking pen, transparent adhesive silicon based gel sheet , //bid details 2 / 73
Tender For supply of slip free finish stainlesssteelsheet size: 1.25 mm x 1250 mm x 3405 mm. material and specification aisi 304. to the following requirements :no. of chequers per 100mm x 100mm area = 16 to 20. length of each chequered projection= 24 +/-0.5mm. width of each chequered projection = 5+/-0.5mm. height of each chequered projection = 1.3+/-0.1 mm. the length with a tolerance of +10mm -0mm. the width with a tolerance of +5mm /- 0mm. as per drawing no. icf/mrvc/c/bt-4-1-001 make/brand : jsl/jindal stainless limited. [ warranty period: 30 months after the date of delivery ]
Tender For supply of slip free stainlesssteelsheet size 1.25 mm x 1250 mm x 3435 mm to specn. no. aisi-304 as per following requirements. (1) nos. of chequers per 100 mm x 100 mm area = 16 to 20(2) length of each chequered projection = 24 +/- 0.5 mm (3) width of each chequered projection = 5 +/- 0.5 mm (4) height of each chequered projection = 1.3 +/- 0.1 mm. (5) the length with a tolerance of + 10 mm - 0 mm. (6) the width with a tolerance of + 5 mm - 0 mm. [ warranty period: 30 months after the date of delivery ]
Tender For supply of stainlesssteelsheets with specification as per irsm - 44/97 size 4 mm x 1200 mm x 6000 mm. note:plus or minus 5 % quantity variation shall be acceptable on the ordered quantity. [ warranty period: 30 months after the date of delivery ]
Tender For supply of slip free finish stainlesssteelsheet of size: 1.25mm x 1250mm x 3435mm to grade x5crni18 10 to rdso specn. c-k201 with amd-1 and corrigendum-1 or latest to following requirements.no of chequers per 100mm x 100mm area = 16 to 20 length of each chequered projection = 24 +/- 0.5mmwidth of each chequered projection = 5 +/- 0.5mmheight of each chequered projection = 1.3 +/-0.1mm.the length with a tolerance of +10mm -0mm.the width with a tolerance of +5 mm -0mm. [ warranty period: 30 months after the date of delivery ]