Latest steel reservoir Tenders | Government steel reservoir Tenders

CTN :40521529

09 Jun, 2025 NA

Kolkata - West Bengal

Tender For supply of hand pump , unloading manifold , pump coupling , service kit , wire rope assembly , set of hydraulic hoses , service kit for luffing cylinder , service kit for telescopic cylinder1 , service kit for telescopic cylinder2 , oil temperature sensor , ptfe tape roll teflon , dowty washer , slew limit switch , hoist limit switch , pipe clamp , o ring for hydraulic reservoir , misc hydraulic fittings and connector , joysticks , ab plc micro logix paramtr and calibratn , dcv controller program andcommunication , 415vac220vac 750va transformer , 2 pole ac mcb , selector switch , push button stop , green indication 24v dc , red indication led 230v ac , yellow inducation red 230v ac , blue indication led 230v ac , 3 pol 65a contactor , red indication 24v dc , 1 pole mcb ac , 200w, panel space heater , oil tank level switch , cable reel

CTN :40253011

31 May, 2025 NA

North 24 Paragana - West Bengal

Tender For bid to ras tender for supply of safety filter(jd mk-i plate-03) , bushing (plate-j-15) , lub fitting (ispl plate-i02) , cap screw m12 x 100 , turn indicating lamp lh(ispl plate-h03) , turn indicating lamp rh (ispl plate-h03) , washer(i01) , washer , rod (plate-i07) , flange nut(plate i-08) , stud(plate-j01) , t bolt type vacuum indicator(ispl plate-b03) , snap ring , wrench 10 (tat jd 315se mk-1 p-313 sl no-27) , tubuler spnr 12.5x21 , rod(plate -j01) , wear plate (ctlg plate-i10) , cap screw , adaptor( plate-j07) , hose clamp , rod , spanner 19x22(tool list) , hose clamp t bolt type , washer , accelerator rod , hex nut , rod(plate-j01) , rod , spnr 10x12 (tata jd 315se p-303 sl no-11) , fitting , knob , spanner 24x27mm (ojde) , rubber bellow (upper cooling water line to thermos , o ring(plate-k03) , valve(r2) , rod (plate-i08) , pin assy , adapter (ispl plate-j02) , wrench socket 2 , wire harness park break , union fitting (ispl plate-f05) , support(plate-j01) , adapter(plate-f03) , knob , push rod(r2) , spanner 24x27 mm (ojde) , rod , switch park brake(ms sl-286) , horn , flange nut , clamp (p-15) , tee fitting(p-179) , fitting (plate-j15) , wrench adjustable 305mm , jet assy , bell crank(plate-i08) , cap screw , arm service lock(plate i-06) , spacer(plate-j01) , grip with horn switch knob ctlg plate-j12) , o ring , hyd hose (ispl plate-f03) , spacer (plate-b06) , oil line (p-179) , hose assy , oil line(plate -f01) , spanner open end 18x 19 , hammer 1-1 by 2 , pin (ispl plate-i12) , spanner open end 16x 17 , pin , elbow fitting , elect temp gauge(ctlg plate-h05) , door retainer latch unit (tata jd 315v) , water reservoir , bushing , cabin harness , cutter for exhaust valve seat(smt-32) , knob(plate-j12) , switch pressure-(130psi) (price list tata jd 315v , stay rod lh & rh , hose , dial indicator , hose tank to fuel tank , pin(plate-j15) , pin (ispl plate-k03) , hyd hose (ms sl-314) , gear shaft lever switch assy , hydraulic hose , muffler extention(ispl plate-b04) , hydrolic hose (ispl plate-f01) , shaft seal , base , running disc , pedal lh (plate-j-15) , pedal rh (plate-j-15) , gauge speedometer (ispl plate-h03) , magnetic stand , hose (ispl plate-j04) , lever , knob , interior light (os sl no-407) , bar extension 2 , u ring , lever(plate-07) , tie rod end (ctlg plate-j01) , hose (ispl plate-b06) , digital hour meter (p-344) , wiper motor(ctlg plate-h02) , seal kit (p-347) , knob , tapper roller bearing (p-63) , screw joint coupling 9 by 26 inch (smt-28) , cassette ring (zf ser no 260) , tube , grab sleeve , assy hour meter(r1) , driver , assy tool box , measuring cover , indicator for transmeter , i clutch disk (ispl-old) , insert , handle set for water pump(smt-30) , piston rod s by a(315se mk-1 p-277) , atomiser assy includes 17 , 18 , 19 and 20 (ms sl-67) , steering cylinder (tata jd 315se plate j31) , cutter for 30o(smt-33) , instrument cluster , glass-4 , piston rod s a (315se mk-1 p-293) , wheel stud puller , glass-1 (tata jd 315v) , glass-6 (tata jd 315v) , glass 5(os sl no-347) , bell crank (plate-j-01) , straightedge , high pressure pump super(smt sl-10) , door glass rh & lh , fender l h (tata jd 315v) , fender (r h) (tata jd 315v) , seat(plate-g03) , entrance door(os sl no-335) , track rod , induction coil assy (ispl plate e4 , e6-7) , rear swivel door lh(os sl no-337) , rear swivel door rh(os sl no-338) , bucket tilt ldr cylinder , switch reverse control (ispl plate-c03) , single point ripper(ref-k03) , frame(i14) , wheel rim (hd) , backhoe bucket (0.09 cum)(tata jd mk-1 plate k04) , backhoe bucket(0.18 cum)-ispl plate-k05 , ditch cleaning bucket0.35 cum) , boom lock solenoid(ctlg plate-h02) , crain attachment hb crain , sliding frame(p-177) , converter (alt no from price list-15815) , converter , sliding frame with piston bushing 7 seal , gear box assy(zf p-64)

CTN :40469557

13 Jun, 2025 NA

North 24 Paragana - West Bengal

Tender For purchase of spares - supply of washer(fig-130) , spring washer m12 (r.h)(ctlg fig-40) , bolt , 1 by 2 inch sq dr bi hex socket 27mm , switch panel 4wd 4wd actuator , ring snap throttle shaft , clamp , o ring (ctlg fig-2210) , o ring , piston , screen & cap filter , stud , gauge fuel (fig-12) , o ring , cable assy , hose , link ball , collar (fig-46) , cable , ring comp , shim assy , element , check valve , elbow , piston seal , flap rust 1300x24 , shim , bushing , shim , lamp , oil seal (fig-63) , cable (komatsu motor grader page 21-36) , guide , filter lub oil assy , cable assy , seal , belt water pump , service kit , hose(fig-70) , hose , bearing , shoe assy (chapter parking brake) , cushion assy , blade lift cylinder seal kit(fig-90) , tube compressure air inlet , cover assy (fig-19) , bearing , cyl kit (service kit) , valve shut down , service kit master cyl repair kit(ms sl no-697) , steering cyl kit , seal kit (fig no-96) , cable assy , techo service meter , seal kit (fig no-98) , cable assy , switch solenoid(44tc) , cable assy , seal kit (fig no -97) , seal kit(fig-99) , cable(fig-05) , unloader valve with tyre inflator , repair kit for scarifier cyl , guide , cable , cable , wheel cyl service kit , slave servo(ctlg fig-60f) , valve assy service kit , brake piping (2 by 4) air over hydraulic , cutting edge(fig-130) , propeller shaft assy , cylinder assy(komatsu motor grader page 24-23) , condensing unit & auto drain valve , wheel cyl assy (oem) , pilot check valve assy (fig no-108) , reservoir 10 litre(fig-60g) , steering cylinder(mg605r2 fig no 89) , steering cyl assy(fig-89) , kit , master cyl assy (fig-56) , hyd control valve (rh)(ispl fig-103) , hyd control valve (lh)(ispl fig-104) , leaning cyl assy (fig-86) , joint assy , propeller shaft , starter motor , blade shift cyl assy (fig-83) , shoe assy , valve assy

Central Government / Public Sector

CTN :40510269

09 Jun, 2025 NA

Rayagada - Odisha

Tender For supply of accessories for hydraulic rescue device (hrd) make: lukas (1) reservoir assembly - t ank p 630 sg part no. 175070350s [ warranty period: 12 months after the date of delivery ]

Central Government/Public Sector

CTN :40448914

13 Jun, 2025 NA

Sirsa - Haryana

Tender For repair and overhauling service - ground equipment;ground equipment; no; buyer premises-scope of work for servicing of ground equipment- regular servicing and preventing maintenance of ground equipment is essential to ensure the safety, efficiency, and reliablility of ground operations. gsse plays a critical role in supporting aircraft turnaround, maintenance, and logistics function. over time, continous use of equipment such as ladders, hydraulic rigs, trolleys, towing arms, and refilling systems can lead to mechanical wear, fluid degradadation, and unnoticed structural fatigue. faulty or poorly maintained gse poses a direct risk to personnel, aircraft, and ground assets. servicing ensures that all mechanical, hydraulic and structural components function safely and as intended. scope of work: 1. ladder frame to be inspected and weld joints for cracks for deformation and it is to be repaired. 2. anti-slip steps, handrails and safety locks to be inspected and to be rectified/changed. 3. caster wheels are to be checked for wear, lock function and lubrication and all the faulty parts are to be repaired/changed as per condition of the(f) equipment. 4. brake function and tow hitch mechanism is to be checked and to be repaired/changed as per condition of the equipment. 5. rust to be removed where required. 6. hoses and fittings are to be inspected for leaks and damages and thoses are to be repaired. 7. filters are to be changed if required. 8. cylinders are to be checked for cracks and are to be repaired. 9. structural integrity of frame and platform is to be checked and repaired as per requirement. 10. wheels are to be checked for alignment or any other bearing issues anfd same is to be repaired. 11. parking brake is to be checked along with the towbar assembly and is to be repaired as per requirement. 12. load securing hooks or rails are to be checked and to be made operational. 13. reservoir is to be checked for contamination and fuel level 14. hand/foot operations is to be checked and made serviceable. 15. dispensing hose nozzles and fittings are to be checked and are to be made serviceable. 16. straightness and structural integrity of bar is to be checked and same is to be rectified if required. 17. all the moving parts are to be lubricated with correct grade of lubes/greases. 18. conduct ndt if required for stress crack detection. 19. cleaning of equipment is to be done before and after servicing. 20. service status and next due date is to be tagged. 21. summary report is to be given to the user after repair of all the repairing work done. 22. adhere to oem servicing guidelines and intervals. 23. use of oem grade consumables and spare parts.

Central Government / Public Sector

CTN :40475539

19 Jun, 2025 NA

Secunderabad - Telangana

Tender For supply, installation & commissioning of hydraulic job clamping wise for fixing of avm pads to 60kva lhb ac transformers on table (with work table, power pack, panel box & clamping wise with cylinder) with accessories consisting the following items and drawing en closed. 1) work table of size:1900x800x750 with top ms sheet of 8mm thickness 2) clamping wise with cylinder (heavy duty). 3) hydraulic p ower pack of electrical pump operated for hydraulic operation with foot pedal switch with 3hp motor, 5lpm pump, m28 coupling, bell hou se, manifold block, valve 240v, relief valve, suction strainer, breather, oil level indicator, pressure gauge, 70lts reservoir, oil grade syste m-68, electrical control panel with electrical safety for men working and equipment. [ warranty period: 30 months after the date of deliver y ]

State Government

CTN :40404619

02 Jun, 2025 38.19 Lacs

Banaskantha - Gujarat

Tender For providing consultancy service for preparation of hydraulic structure design, estimate and dtp of main canal (15 no.of structures) ch.33402 mt to 46024 mt of dantivada reservoir project.

CTN :40434514

12 Jun, 2025 NA

Gorakhpur - Haryana

Tender For supply of stainless steel reservoir 200 ltrs to drg no icf/std-3-5-065, col-1, alt-c [ warran ty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :40329469

22 May, 2025 NA

Tiruchirappalli - Tamil Nadu

Tender For supply of stainless steel reservoir 20 ltrs to drg no icf/sk3-0-5-008, alt 'b' col.i [ warranty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :40255191

21 May, 2025 NA

Hubli - Karnataka

Tender For supply of stainless steel reservoir 200 ltrs to drg no icf/std-3-5-065, col-1, alt-c or latest [ warranty period: 30 months after the date of delivery ]

Steel Reservoir Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government / Public Sector

Central Government/Public Sector

Central Government / Public Sector

State Government

Central Government/Public Sector

Central Government/Public Sector