Latest steel shaft Tenders | Government steel shaft Tenders

State Government

CTN :43467490

16 Jan, 2026 NA

Delhi - Delhi

Tender For corrigendum : s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

Central Government/Public Sector

CTN :43519572

29 Jan, 2026 NA

Sonbhadra - Uttar Pradesh

Tender For supply of solid steel shaft

Central Government/Public Sector

CTN :43290429

19 Jan, 2026 86.44 Lacs

Dipka - Chhattisgarh

Tender For corrigendum : supply of procurement of spares for flowmore make pump - pump shaft part no fm5911 moc astm a 276 ss410 , key for pump half coupling part no fm5912 moc en9 , oil seal de for bearing cover outer de part no fm5913 moc nitrile rubber , counter sunk screw for st cover to suc cover part no fm59110 moc ht steel is 1367 gr 10point8 , external threaded dowel pin for st cover to suc cover part no fm59111 moc ht steel is 1367 gr 10point8 , stuffing box cover part no fm59112 moc 2point5percentage ni ci is 210 fg 260 , pipe plug for stuffing box cover part no fm59113 moc mi , wearing ring for stuffing box cover part no fm59114 moc astm a 743 ss ca 15 , o ring for st box cover to suc casing suc casing to cover plate part no fm59119 moc nitile rubber , cover plate part no fm59120 moc 2point5percentage ni ci is 210 fg 260 , counter sunk screw for cover plate to suc cover part no fm59121 moc ht steel is 1367 gr 10point8 , external threaded dowel pin for st cover to suc cover part no fm59122 moc ss316 , counter sunk screw for partition plate to suc cover part no fm59123 moc ht steel is 1367 gr 10point8 , partition plate part no fm59124 moc 2point5percentage ni ci is 210 fg 260 , external threaded dowel pin for partition plate to diffuser part no fm59125 moc ss316 , diffuser part no fm59127 moc 2point5percentage ni ci is 210 fg 260 , external threaded dowel pin stage to delivery diffuser part no fm59130 moc ss316 , large seating bush for del cover part no fm59136 moc bronze is 318 ltb 5 , counter sunk screw ls bush to del casing part no fm59137 moc ht steel is 1367 gr 10point8 , balance valve part no fm59138 moc bronze is 318 ltb 2 , sleeve nut two no rh 2 no lh thread part no fm59145 moc steel , shaft sleeve nde at balance valve cover part no fm59146 moc astm a 276 ss410 h , key for suction impellor balance valve part no fm59152 moc en9 , key shaft for stage impellor both end round part no fm59153 moc en9 , neck bush diffuser part no fm59154 moc bronze is 318 ltb 5 , wearing ring for st stage partition plate part no fm59155 moc astm a743 ss ca15 , shaft sleeve imp to imp part no fm59156 moc astm a 276 ss410 h , case spacer bushing for cover plate part no fm59157 moc bronze is 318 ltb 5 , water seal ring part no fm59159 moc bronze is 318 ltb 2 , split gland part no fm59161 moc 2point5percentage ni ci is 210 fg 260 , dowel pin for gland part no fm59162 moc en9 , o ring for shaft sleeve part no fm59163 moc nitrile rubber , shaft sleeve de part no fm59164 moc astm a 276 ss410 h , pipe plug for air seal dran filling part no fm59172 moc mi , impeller single suction for second stage part no fm59129 moc astm a 743 ss ca 6nm

CTN :42685019

14 Jan, 2026 NA

Fatehgarh Sahib - Punjab

Tender For bid to ras supply of bench grinding machine , digital pyrometer , spark test apparatus , metallurgical cut off machine , standard prepared readymade samples specimen with photographs , venturimeter and orificemeter apparatus , bernoulli s theorem apparatus , darcy law apparatus , pressure measuring bench , digital spring testing machine , model of refrigerationcycle , model of window air conditioner , refrigeration cycle testing rig , digital anemometer , model of open type refrigerant compressor , thermocouple , infrared thermometer , blow off cock steam stop valve feed check valve economizer , model of air compressor , model of lancashire boiler , model of nestler boiler , demonstration actual cut section model of two stroke single cylinder petrol engine , actual cut section model of four stroke single cylinder diesel engine , model of solex carburettor , model of amal carburettor , model of ignition system of an automobile , model of water cooling system of an automobile , model of lubrication system of i c engine , mpfi four stroke four cylinder petrol engine test rig with eddy current dynamometer , model of mpfi system , model of crdi system , digital vernier callipar , digital micrometer , height gauge , go no go thread plug gauge 1 , go no go thread plug gauge 2 , go-no go snap gauge 3 , go-no go ring gauge 4 , go-no go ring gauge 5 , cylinder rollers and spherical balls , slip gauges set , surface roughness tester , vernier bevel protractor , surface plate , magnetic v block , dial indicator with stand , angle deckor with set of angle gauges , cylindrical bore gauge , screw thread micrometer , sine bar , feeler gauge , wire gauge , radius gauge , comparator stand , angle plate , mechanical comparator , clinometer , gear tooth vernier , metallic try square , meteric thread pitch gauge , electronic weighing machine , digital tachometer , single plate clutch , multi plate clutch unit , centrifugal cluth unit , cut section of synchromesh gear box , propeller shaft , cut-section of differential assembly , model of mechanical brake , model of hydraulic brake system , ackerman steering gear mechanism , davison steering gear mechanism , model of rack and pinion steering gear , model of ac pump , model of su pump , lead acid battery , battery charger , automobile electric system , brake master cylinder , sliding mesh gear box , cut section model of 4 cylinder 4 stroke petrol engine , ac induction motor with vfd for motorizing already existing models in lab , models of different wooden joints , models of screw threads , models nuts and bolts , models of locking devices , models of keys and cotter joints , models of riveted joints , models of bearing assembled drawing , model of drilling jig , model of machine vice , model of piston , model of connecting rod , model of crank shaft and flywheel assembly , models of different types of gears

CTN :43343828

17 Jan, 2026 80.0 Thousand

Sagar - Madhya Pradesh

Tender For corrigendum : tender for supply of reduction valve , relay aev 5201 24v , gasket cyl head , assy radiator , 17w hi power wiper motor , assy propeller shaft front - from aux. g , slave cyl clutch , temp transducer , crown wheel and tail pinion-41-71 orliko , assy release cable comp. -centre flap- , assy inner handle lh , pump water , armature assy

CTN :42588392

27 Jan, 2026 NA

Uttara Kannada - Karnataka

Tender For corrigendum : tender for supply of rectifier , indicating lamp , power contractor one no each type , power hrc fuse link one set each type used , control fuse link , push button , auxilary contactor rated 6a with 4n0.contact having coil vol , limit switch , brake lining , input gear coupling slewing , eletric motor 25hp 1440 rpm , 3f , 50cs , 380v , packing , key , electromagnetic brake assembly , packing , breather , oil level indicator , drain plug , clutch , key , split pin , oil seal , handle , ball , pinion shaft , grease nipple , packing , oil seal , key , external circlip , split pin , brake shoe , brakelining , oil seal , internal circlip , packing , bush , brake segment , brake lining , deadman brake assembly , pinion shaft , key , gear wheel , key , main shaft , oilseal , rope clamp , allen bolt + sp. washer , electric motor 5hp 380v 1440 rpm 3 f 50c/s , packing , key , electro-magnteic brake assembly. , breather , oil filler with adoptor , oil level indicator , drain plug with adoptor , packing , key , worm shaft , main shaft , packing , packing , seal cover , packing , oil seal , pinion , key , gear wheel , grease nipple , drive shaft , packing , pinion , key , slewing bearing geared , tightening botl with sp.washer , tightening botl with sp.washer , grease nipple , split pin , rivet , rivet , pinion helical , pinion , drive shaft , securing plate , terminals

CTN :42860760

31 Jan, 2026 NA

Uttara Kannada - Karnataka

Tender For corrigendum : tender for supply of diesel engine spares c c -o-ring di 30x4 21 a7 , gasket monel , annealed gasket , gasket , piston 2 parts assembly , gasket , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , outlet gasket , gasket , tighening tool , inlet push rod , anode , non return valve , filter element , rack sensor fr-xxbnn151349 , speed sensor , fr-xxbnn151349 , speed sensor fr-xxbnn151349 , measurement device , bolt extract socket , red signal light , fr-xxbnn151349 , spring injector , o-ring r10 , gasket a 21x26 cu b1 , thermometer , loctite 243 nut lock , bearing shell ch7-pl5-80 , bearing shell , o-ring , gasket 4 holes 120x120x1 , 2 , end section , gasket , stbd diesel multipurpose duct c-901 , portdiesel multipurpose duct c-901 , handling of cylinder head , o-ring r3 , pin , broach assembly gasket , spring , clip dn 113 , o-ring front bearing of compressor pinion shaft , o-ring rear bearing of compressor pinion shaft , compressor front bearing labyrinth gasket , turbo charger speed sensor st115 , air filter , motor compressor cover o-ring timing gear side , thermometer , temperature sensor , temperature transmitter , temperature transmitter , port diesel pyrometric duct c-902 , adaptator t123-2 , inlet-exhaust vlave half shell , temprature sensor fr-98703000034 , thermostatic valve 74-83 c , nut lock with slot hm 10 stainless a2-80 , gasket , fuel make up pump , gasket , gasket , expansion bellows , air distributer , transmitter , tempreture sensor , pressure transmitter , transmitter , pressure transmitter , o-ring 6 , 4 x 1 , 9 r5a vit 80 sh , pressure transmitter , pressure transmitter , pressure transmitter , temperature transmitter , temperature transmitter , temperature sensor , fitting&dismantling of injection pp plunger-barrel ass t193 , annealed gasket a 22 x 32 cu b1 , 250/45 bar pressure reducer c615 , piston imf hp air pressure reducers 250-90 bar , piston imf hp air pressure reducers 45-20 bar , o-ring an 11 60c7 , o-ring an64 , extraction of liner and piston/con-rod assembly t139a , gasket , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , oil separator , fr-xxbnn151349 , star filter element , fr-xxbnn151349 , nc solenoid valve , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , injection pipe , fr-xxbnn151349 , combustion chamber cock fr-xxbnn151341 , refill can , reference fr-xxbnn151347 , iso 5-2 pneumatic , distributor fr-xxbnn151349

CTN :43502924

19 Jan, 2026 NA

Sundergarh - Odisha

Tender For tender for supply of auma make electric actuator spares d d - auma torque switch drive ass for sa6 , torque sw drive assy sa12 sa15 , t s d assembly for sa 25 auma actuator , torque switch drive assy sa30 tandem , torque sw drive assy sa50 sa60 , tor sw drive assy pn45 sa100 , auma worm shaft assembly sa6 single , auma worm shaft assembly sa6 double , auma worm shaft assembly sa12 double , worm shaft assembly sa15 single , worm shaft assy sa25 sa30 , worm shaft assembly sa30 double , worm shaft assly part no 21 for sa50 , worm shaft assembly sa50 double , worm shaft assembly sa100 double , hollow drive shaft assy sa3 sa6 , hollow drive shaft assy sa12 sa15 , hollow shaft sa12 15 s hds 007 auma , hollow drive shaft assly p n24 sa25 , hollow drive shaft assembly , hollow drive shaft p n 24 for sa50 , hollow drive shaft assy sa50 60 double , hollow drive shaft assy sa100 , auma compression spring sa6 dia 46x30 , auma compression spring sa12 dia 55x40 , compression spring sa25 dia 82x50 , comression spring sa100 , auma clutch ring sa6 z 29 , auma clutch ring sa12 z 39 , clutch ring sa25 z 45 , clutch ring part no 26 for sa100 auma , auma o ring kit for sa3 sa6 actuator , auma o ring kit for sa12 sa15 actuator , o ring kit for sa25 sa60 actuator , set of o rings kit auma make type sa100 , auma oil seal kit for sa3 sa6 actuator , auma oil seal kit for sa12 sa15 actuator , oil seal kit for sa25 sa60 actuator , oil seal set for sa100 type auma act pa , circlip sa3 sa6 , auma circlip kit for sa12 sa15 actuator , circlip kit for sa25 sa60 actuator , circlip part no 23 sa100 , auma clutch fork assembly sa6 , clutch fork assly part no 8 for sa25 , clutch fork assly for sa100 part no , auma retainer ring sa6 dia 1 7x215 , retainer ring sa25 dia 2 25x340 , retainer ring sa100 dia 3x480 , declutch lever pt no 5 auma sa actuator , declutch lever sa100 with stopper , declutch tripping arm sa6 47x25x6 , auma return spring sa6 wire dia 2 25 , sub assly shaft&pinion wsd 15 45x20 , compression spring sa6 dia 6 2x16 , four train assembly 480 turns , auma limit switch 2no 2nc ag crimping , auma torque switch 2no 2nc ag crimping , auma limit switch 2no 2nc ferrulcrimp , auma torque switch 2no 2nc ferrulcrimp , ls 2no 2nc 0 75sqmm 1000mm std ferrul , ts 2no 2nc 0 75sqmm 1000mm std ferrul , sub asly ewg 2 wire sa & sar type ag , sub assy ewg for fixed ratio , auma actuator motor md0v 071 00 ai 06 , auma actuator motor md0v 071 01 ai 08 , motor 2 5kw 2800rpm sa25e125 , motor for sa25e180 auma actuator , motor md0v 132 15 000 2 415d5 , auma cont mod asy 1 xmp 1tfr epac opto , auma power mod asy 1 xmp 1tfr epac opto , auma control module complete for v1 a , auma power module complete primary 415v , control module complete v1 a s15 , control module assy wdp epac c , power module for ssr epac 415v 400v , auma control module for epac c opto , auma power module for epac c st opto , pb cover sub asly forled epac 2pole , pb cover sub asly epac c lcd epac 2p , pb cover sub asly for led epac 3p s19 , wheel sa6 z 24 d 47 5x10 90 180rpm , wheel sa6 z 29 d 55 7x10 63 125rpm , wheel sa6 z 33 d 62 06x10 45rpm , wheel sa6 z 38 d 70 6x10 32rpm , wheel sa25 z 27 d 75x18 90 180rpm , wheel sa25 z 32 d 87 5x18 63 125rpm , wheel sa25 z 42 dia 110 7 x 18 32 rpm , wheel sa25 z 37 d 97 5x18 22 45rpm , wheel sa100 z 32 d 112 9x22 63 125rpm , ac motor 7 5kw 2800 rpm for sa100a90 act

CTN :43234689

28 Feb, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For corrigendum : tender for supply of pinion shaft with pinion for l.o.pump , compensator complete , bearing port stbd axial no-3 , bearing port stbd radial no-7 , non return valve pn40 nd32 , shaft seal ring , dummy bearings , friction clutch , compression spring , compression spring , shaft seal ring 240-270x15 , taper roller bearing no.8578-8520 , wheel shaft , micrometer , pump lub oil motor driven , non return valve no65 , non return valve nd80 orrice , pressure regulating valve , temprature regulating valve , thermometer l200mm for brg no-1 , non return valve nd65 , stop valve nd 32 , gauge pressure 0-10bar , gauge pressure 0-10bar , pressure regulating valve p-6 bar , pressure regulator p-25bar , check choke valve , stbd thrust bearing no.6a , shaft seal ring , wheel gear 2nd reduction , spherical roller bearing 22210c , tapper roller bearing 31313 , bearing cylinderical roller nu313 , wheel gear 2nd reduction , set of spindle right handed helix , bearing roller , shaft sleeve , slide shaft seal , bearing cylindrical roller , tooth coupling , cylindrical roller bearing nj 408 , intermediate shaft , intermediate gear wheel , cylindrical rollerr bearing nj 308 ecp

CTN :43442253

14 Jan, 2026 NA

Ganganagar - Rajasthan

Tender For supply of spares of auma make actuators spares at stps, suratgarh against ssp-42 - actuator model sa-12 e 90, comm.no. 261000541, limit switch (2no+2nc) (part no-7.1), actuator model sa-12 e 90, comm.no. 261000541, torque switch (2no+2nc) (part no-7.2), actuator model sa-12 e 90, comm.no. 261000541, torque switch drive assly (part no-45), clutch ring part no. 26 for auma make actuator model no sa 15 a32, clutch fork assembly part no. 8 for auma make actuator model no sa 15 a32, worm shaft assembly, part no. 21 for auma make actuator model no sa 15 a32, stem nut-typea, part no. 4.12 for auma make actuator model no sa 15 a32 (drive socket ), torque switch (2no+2nc) for actuator model sa 12 e 32/90, torque switch drive assy for actuator model sa 12 e 32/e90, limit switch drive assy for actuator model sa 12 e 90 part no. 31, actuator model sa-12 e 90, comm.no. 261000541, limit switch drive assembly (part no-31), actuator model sa-25 , worm gear (wheel) (part no-2.6), actuator model sa-25 a 90 , limit switch counter gear (part no-44) (four train assembly 480 truns), actuator model sa-25 a 90 , torque switch drive assembly (part no-45), actuator model sa-25, limit switch (2no+2nc) (part no-7.1), actuator model sa-25 , worm shaft assembly (part no-21), thurst bearing with race for actuator model sa-25 e 125 (part no. 44.03 , 44.04), limit switch drive assy for actuator model sa-25 e 125, oil seal set for actuator model sa-25 e 125(o-ring kit for sa25, complete actuator sa25 a-32 comm. no. 11699247, actuator model sa-30, clutch fork assembly (p. no-8), actuator model sa-30, hollow drive shaft assy complete (p. no-24), actuator model sa-30, motor pinion(p. no-2.1), actuator model sa-30 limit switch drive assy (p.no-31), actuator model sa-30 oil seal set p.no-013 -014), actuator model sa-30, limit switch counter gear (p. no-44), actuator model sa-30, torque switch drive assly (p.no-45), actuator model sa-30, clutch ring (p.no-26), actuator model sa-30,stem nutdrive socket , actuator model sa-50 e 90 comm.no. 261000545, clutch fork assembly (part no-8), actuator model sa-50 e 90 comm.no. 261000545, torque switch drive assembly (part no-45), actuator model sa-50 e 90 comm.no. 261000545, clutch ring (part no-26), actuator model sa-50 e 90 comm.no. 261000545, limit switch counter gear (part no-44) (four train assembly 480 truns), actuator sa50-e90 no. 261000545, warm shaft assembly part no-21, actuator sa50-e90 no. 261000545, limit switch drive part no-31, actuator sa50-e- 90 , worm gear part no. -2.6, actuator model sa-50 e 90 comm.no. 261000545,hollow drive shaft assembly complete (part no-24), actuator model sa-60 e 45 comm.no. 7038607001-gb-05, clutch fork assly (p. no-8), actuator model sa-60 e 45 comm.no. 7038607001-gb-05, hollow drive shaft assy. complete (p. no-24), actuator model sa-60 e 45 comm.no. 7038607001-gb-05, limit switch (2no+2nc) (p. no-7.1), actuator model sa-60 e 45 comm.no. 7038607001-gb-05, torque switch (2no+2nc) (p. no-7.2), actuator model sa-60 e 45 comm.no. 7038607001-gb-05, limit switch counter gear (p. no-44) (four train assembly 480 truns), actuator model sa-60 e 45 comm.no. 7038607001-gb-05, torque switch drive assly (p.no-45), actuator model sa-60 e 45 comm.no. 7038607001-gb-05, seal ring (p.no-5.09), actuator model sa-60 e 45 comm.no. 7038607001-gb-05, clutch ring (p.no-26), actuator model sa-60 e 45 comm.no. 7038607001-gb-05, limit switch drive assly (p.no-31), actuator model sa-60 e 45 comm.no. 7038607001-gb-05, oil seal kit, actuator model sa-60 e 45 comm.no. 7038607001-gb-05, stem nut drive socket, actuator model sa-100, clutch fork assembly (part no-8), actuator model sa-100, worm gear (part no-2.6), actuator model sa-100, motor pinion (part no-2.1), actuator model sa-100, limit switch counter gear (part no-44)(four train assembly 480 truns), oil seal set actuator model sa-100 e 125, actuator model sa-100, hollow drive shaft assembly complete (part no-24), actuator model sa-100, worm shaft assembly (par

Steel Shaft Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government/Public Sector

Central Government/Public Sector