Latest structural steel work Tenders | Government structural steel work Tenders

CTN :40389042

30 Jun, 2025 NA

Kolkata - West Bengal

Tender For bid to ras corrigendum : construction of artificial rock climbing wall cum slithering platform in garrison battalion ground - earth work in excavation by mechanical means hydraulic excavator oblique manual means in foundation trenches or drains not exceeding 1 dot 5 m in width or 10 sqm on plan , providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering , providing and laying in position specified grade of reinforced cement concrete , brick work with burnt clay fps non modular bricks of class designation 7 dot 5 in foundation and plinth in ratio cement mortar 1 ratio 4 bracket 1 cement ratio 4 coarse sand , 12mm thick cement plaster 1ratio4 , filling available excavated earth excluding rock in trenches plinth sides of foundations , supplying and filling in plinth with jamuna sand under floors including watering ramming consolidating and dressing complete , steel reinforcement for rcc work including straightening cutting bending placing in position and binding all complete upto plinth level thermo mechanically treated bars , supplying of m s bolts round holding down of anchor boltds with nuts and washer plates complete , structural steel work , providing and fixing ms chequered plate 5mm thick , providing and fixing 0dot8mm thick colour coated sheet for shed , designing providing and fixing frp 3d panel with minimum 6 mm thickness at center and 10 mm at flanges , providing and fixing ss top belay bar , movable climbing holds , providing seat harness , static rope 10 mm , carabiner , providing bracket fdotodot8 bracket , providing mitton , gri gri , providing quick draw , 30mm manila rope bid number/ & ( * ) : gem/2025/b/6191380 dated/ + : 18-05-2025 bid document/ 3 3 1 / 19

CTN :40862067

09 Jul, 2025 NA

Bhind - Madhya Pradesh

Tender For under case number 11/25x3/5, small construction work, maintenance, repair, patchwork and material supply work in ward number 09 under the body area.-, , cement concrete grade m-10 (nominal mix with 40 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, foundations, footings, bases of columns, etc. for mass concrete centering and shuttering including strutting, propping stretchin g etc. complete for and removal of form work by sheet plate or ply wood shuttering for:, cement concrete grade m-20 (nominal mix) with 20 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, providing and laying cement concrete grade m-20 (nominal mix 1:1.5:3) with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate/screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, i/c cutting of joints @ 4 to 5 m interval & filling it with hot applied bitum inous sealant (without dowel bars). (max. thickness 20cm)", , thermo-mechanically treated bars. (fe 500 d or more)-"reinforcement for r.c.c. work including straightening, cutting, bending, placi ng in position and binding upto floor level including cost of binding wire, wastage and over laps upto 12mm horizontal/inclined pos ition of reinforcement bars in slab and beams, plinth, chajjas, lintels, upto 4.5m vertical length of reinforcement in wall columns (over laps shall be provided as per requirement of is: 13920; is 456 & sp: 34) etc. complete.", construction of granular sub-base by providing coarse graded material (cbr>30), spreading in uniform layers with motor grader on pr epared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400.", structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, , two or more coats on new work.-"distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.", 300 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., 450 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints, 600 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., ,

CTN :40862068

09 Jul, 2025 NA

Bhind - Madhya Pradesh

Tender For under case number 04/25x3/5, small construction work, maintenance, repair, patchwork and material supply work in ward number 02 within the body area.-, , cement concrete grade m-10 (nominal mix with 40 mm maximum siz of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work u to plinth level., , foundations, footings, bases of columns, etc. for mass concrete."-"centering and shuttering including strutting, propping stretchin g etc. complete for and removal of form work by sheet plate or ply wood shuttering for:", , cement concrete grade m-20 (nominal mix with 20 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level., , providing and laying cement concrete grade m-20 (nominal mix 1:1.5:3) with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate/screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, i/c cutting of joints @ 4 to 5 m interval & filling it with hot applied bitum inous sealant (without dowel bars). (max. thickness 20cm)", , thermo-mechanically treated bars. (fe 500 d or more)-"reinforcement for r.c.c. work including straightening, cutting, bending, placi ng in position and binding upto floor level including cost of binding wire, wastage and over laps upto 12mm horizontal/inclined position of reinforcement bars in slab and beams, plinth, chajjas, lintels, upto 4.5m vertical length of reinforcement in wall columns (over laps shall be provided as per requirement of is: 13920; is 456 & sp: 34) etc. complete.", , construction of granular sub-base by providing coarse graded material (cbr>30), spreading in uniform layers with motor grader on pr epared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400.", , structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete", , two or new work.-"distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.", , 300 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing o f joints.", , 450 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing o f joints.", , 600 mm dia-"providing. laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing o f joints.",

CTN :40862072

09 Jul, 2025 NA

Bhind - Madhya Pradesh

Tender For under case number 11/25x3/5, small construction work, maintenance, repair, patchwork and material supply work in ward number 09 under the body area.-, , cement concrete grade m-10 (nominal mix with 40 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, foundations, footings, bases of columns, etc. for mass concrete centering and shuttering including strutting, propping stretchin g etc. complete for and removal of form work by sheet plate or ply wood shuttering for:, cement concrete grade m-20 (nominal mix) with 20 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, providing and laying cement concrete grade m-20 (nominal mix 1:1.5:3) with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate/screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, i/c cutting of joints @ 4 to 5 m interval & filling it with hot applied bitum inous sealant (without dowel bars). (max. thickness 20cm)", , thermo-mechanically treated bars. (fe 500 d or more)-"reinforcement for r.c.c. work including straightening, cutting, bending, placi ng in position and binding upto floor level including cost of binding wire, wastage and over laps upto 12mm horizontal/inclined pos ition of reinforcement bars in slab and beams, plinth, chajjas, lintels, upto 4.5m vertical length of reinforcement in wall columns (over laps shall be provided as per requirement of is: 13920; is 456 & sp: 34) etc. complete.", construction of granular sub-base by providing coarse graded material (cbr>30), spreading in uniform layers with motor grader on pr epared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400.", structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, , two or more coats on new work.-"distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.", 300 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., 450 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints, 600 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., ,

CTN :40862073

09 Jul, 2025 NA

Bhind - Madhya Pradesh

Tender For under case number 08/25x3/5, small construction work, maintenance, repair, patchwork and material supply work in ward number 06 within the body area.-, , cement concrete grade m-10 (nominal mix with 40 mm maximum siz of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work u to plinth level., , foundations, footings, bases of columns, etc. for mass concrete."-"centering and shuttering including strutting, propping stretchin g etc. complete for and removal of form work by sheet plate or ply wood shuttering for:", , cement concrete grade m-20 (nominal mix with 20 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level., , providing and laying cement concrete grade m-20 (nominal mix 1:1.5:3) with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate/screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, i/c cutting of joints @ 4 to 5 m interval & filling it with hot applied bitum inous sealant (without dowel bars). (max. thickness 20cm)", , thermo-mechanically treated bars. (fe 500 d or more)-"reinforcement for r.c.c. work including straightening, cutting, bending, placi ng in position and binding upto floor level including cost of binding wire, wastage and over laps upto 12mm horizontal/inclined position of reinforcement bars in slab and beams, plinth, chajjas, lintels, upto 4.5m vertical length of reinforcement in wall columns (over laps shall be provided as per requirement of is: 13920; is 456 & sp: 34) etc. complete.", , construction of granular sub-base by providing coarse graded material (cbr>30), spreading in uniform layers with motor grader on pr epared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400.", , structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete", , two or new work.-"distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.", , 300 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing o f joints.", , 450 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing o f joints.", , 600 mm dia-"providing. laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing o f joints.",

CTN :40862074

09 Jul, 2025 NA

Bhind - Madhya Pradesh

Tender For under case number 11/25x3/5, small construction work, maintenance, repair, patchwork and material supply work in ward number 09 under the body area.-, , cement concrete grade m-10 (nominal mix with 40 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, foundations, footings, bases of columns, etc. for mass concrete centering and shuttering including strutting, propping stretchin g etc. complete for and removal of form work by sheet plate or ply wood shuttering for:, cement concrete grade m-20 (nominal mix) with 20 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, providing and laying cement concrete grade m-20 (nominal mix 1:1.5:3) with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate/screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, i/c cutting of joints @ 4 to 5 m interval & filling it with hot applied bitum inous sealant (without dowel bars). (max. thickness 20cm)", , thermo-mechanically treated bars. (fe 500 d or more)-"reinforcement for r.c.c. work including straightening, cutting, bending, placi ng in position and binding upto floor level including cost of binding wire, wastage and over laps upto 12mm horizontal/inclined pos ition of reinforcement bars in slab and beams, plinth, chajjas, lintels, upto 4.5m vertical length of reinforcement in wall columns (over laps shall be provided as per requirement of is: 13920; is 456 & sp: 34) etc. complete.", construction of granular sub-base by providing coarse graded material (cbr>30), spreading in uniform layers with motor grader on pr epared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400.", structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, , two or more coats on new work.-"distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.", 300 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., 450 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints, 600 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., ,

CTN :40862076

09 Jul, 2025 NA

Bhind - Madhya Pradesh

Tender For under case number 11/25x3/5, small construction work, maintenance, repair, patchwork and material supply work in ward number 09 under the body area.-, , cement concrete grade m-10 (nominal mix with 40 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, foundations, footings, bases of columns, etc. for mass concrete centering and shuttering including strutting, propping stretchin g etc. complete for and removal of form work by sheet plate or ply wood shuttering for:, cement concrete grade m-20 (nominal mix) with 20 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, providing and laying cement concrete grade m-20 (nominal mix 1:1.5:3) with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate/screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, i/c cutting of joints @ 4 to 5 m interval & filling it with hot applied bitum inous sealant (without dowel bars). (max. thickness 20cm)", , thermo-mechanically treated bars. (fe 500 d or more)-"reinforcement for r.c.c. work including straightening, cutting, bending, placi ng in position and binding upto floor level including cost of binding wire, wastage and over laps upto 12mm horizontal/inclined pos ition of reinforcement bars in slab and beams, plinth, chajjas, lintels, upto 4.5m vertical length of reinforcement in wall columns (over laps shall be provided as per requirement of is: 13920; is 456 & sp: 34) etc. complete.", construction of granular sub-base by providing coarse graded material (cbr>30), spreading in uniform layers with motor grader on pr epared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400.", structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, , two or more coats on new work.-"distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.", 300 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., 450 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints, 600 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., ,

CTN :40862077

09 Jul, 2025 NA

Bhind - Madhya Pradesh

Tender For under case number 11/25x3/5, small construction work, maintenance, repair, patchwork and material supply work in ward number 09 under the body area.-, , cement concrete grade m-10 (nominal mix with 40 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, foundations, footings, bases of columns, etc. for mass concrete centering and shuttering including strutting, propping stretchin g etc. complete for and removal of form work by sheet plate or ply wood shuttering for:, cement concrete grade m-20 (nominal mix) with 20 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, providing and laying cement concrete grade m-20 (nominal mix 1:1.5:3) with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate/screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, i/c cutting of joints @ 4 to 5 m interval & filling it with hot applied bitum inous sealant (without dowel bars). (max. thickness 20cm)", , thermo-mechanically treated bars. (fe 500 d or more)-"reinforcement for r.c.c. work including straightening, cutting, bending, placi ng in position and binding upto floor level including cost of binding wire, wastage and over laps upto 12mm horizontal/inclined pos ition of reinforcement bars in slab and beams, plinth, chajjas, lintels, upto 4.5m vertical length of reinforcement in wall columns (over laps shall be provided as per requirement of is: 13920; is 456 & sp: 34) etc. complete.", construction of granular sub-base by providing coarse graded material (cbr>30), spreading in uniform layers with motor grader on pr epared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400.", structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, , two or more coats on new work.-"distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.", 300 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., 450 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints, 600 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., ,

CTN :40862078

09 Jul, 2025 NA

Bhind - Madhya Pradesh

Tender For under case number 11/25x3/5, small construction work, maintenance, repair, patchwork and material supply work in ward number 09 under the body area.-, , cement concrete grade m-10 (nominal mix with 40 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, foundations, footings, bases of columns, etc. for mass concrete centering and shuttering including strutting, propping stretchin g etc. complete for and removal of form work by sheet plate or ply wood shuttering for:, cement concrete grade m-20 (nominal mix) with 20 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, providing and laying cement concrete grade m-20 (nominal mix 1:1.5:3) with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate/screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, i/c cutting of joints @ 4 to 5 m interval & filling it with hot applied bitum inous sealant (without dowel bars). (max. thickness 20cm)", , thermo-mechanically treated bars. (fe 500 d or more)-"reinforcement for r.c.c. work including straightening, cutting, bending, placi ng in position and binding upto floor level including cost of binding wire, wastage and over laps upto 12mm horizontal/inclined pos ition of reinforcement bars in slab and beams, plinth, chajjas, lintels, upto 4.5m vertical length of reinforcement in wall columns (over laps shall be provided as per requirement of is: 13920; is 456 & sp: 34) etc. complete.", construction of granular sub-base by providing coarse graded material (cbr>30), spreading in uniform layers with motor grader on pr epared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400.", structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, , two or more coats on new work.-"distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.", 300 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., 450 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints, 600 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., ,

CTN :40862079

09 Jul, 2025 NA

Bhind - Madhya Pradesh

Tender For under case number 11/25x3/5, small construction work, maintenance, repair, patchwork and material supply work in ward number 09 under the body area.-, , cement concrete grade m-10 (nominal mix with 40 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, foundations, footings, bases of columns, etc. for mass concrete centering and shuttering including strutting, propping stretchin g etc. complete for and removal of form work by sheet plate or ply wood shuttering for:, cement concrete grade m-20 (nominal mix) with 20 mm maximum size of stone aggregate-providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level, providing and laying cement concrete grade m-20 (nominal mix 1:1.5:3) with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate/screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, i/c cutting of joints @ 4 to 5 m interval & filling it with hot applied bitum inous sealant (without dowel bars). (max. thickness 20cm)", , thermo-mechanically treated bars. (fe 500 d or more)-"reinforcement for r.c.c. work including straightening, cutting, bending, placi ng in position and binding upto floor level including cost of binding wire, wastage and over laps upto 12mm horizontal/inclined pos ition of reinforcement bars in slab and beams, plinth, chajjas, lintels, upto 4.5m vertical length of reinforcement in wall columns (over laps shall be provided as per requirement of is: 13920; is 456 & sp: 34) etc. complete.", construction of granular sub-base by providing coarse graded material (cbr>30), spreading in uniform layers with motor grader on pr epared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400.", structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, , two or more coats on new work.-"distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.", 300 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., 450 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints, 600 mm dia-"providing, laying and jointing non-pressure (np4) rcc socket & spigot pipes with rubber gasket joint including testing of joints., ,

Structural Steel Work Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors