Tender For withdrawing of old pumpmotorset (no. 2) and reinstallation of new one including some allied works for bore well submersiblepumpmotorset at 19a chetla hut road, kolkata
Tender For supply of gland pecking for wb , element gasket for wb , warm gear 30 teeth for wb , warm shaft wb , spur gear 12 teeth for wb , rack pinion for wb , warm stl 03 for wb , warm lh stl 02 for wb , spur gear shaft for wb , secondary shaft for wb , primary shaft for wb , primary gear for wb , worm gear for wb , worm gear l.h. for wb , spur gear for wb , key for wb , oil seal for wb - 1e for wb , motor gasket for wb , cover gasket for wb , gasket for wb , oil seal for wb , element gear for wb , chain connector of traveling chain carriage assy , oil gun removal part j for oil gun type , spary plate.90j28 for oil gun type , copper clad asbest gasket , set of gear and pinion assembly for gc feeder inlet gate * /bid number : gem/2026/b/7644559 + /dated: 30-06-2026 ' ' / bid document 1 / 29
Tender For repairing with replacement of worn out components, burn out winding of 2nos, 10hp capacity submersiblepumpmotorsets at raw water pumping station under grww.
Tender For providing of custom bid for services - mod and inst work in sinter dispatch series; modification and installation works in sinter dispatch series of sp-ii 1.modification of drive platform for conveyors c-74, c-75 and c-76 dismantling of the existing drive system platform and associated structures of conveyors c-74 and c-75 in the sinter dispatch series of sp-ii. decoupling and removal of the existing gearbox and motor drive assemblies of c-74 and c-75. dismantling of the existing drive stools and platform base structures. fabrication of new drive stools and drive platform for installation of motor and gearbox as per drawing. erection and installation of the newly fabricated stool and drive platform, followed by mounting and alignment of the new motor and gearbox assemblies. for conveyor c-76, the scope includes: decoupling and removal of the existing motor. dismantling of the existing motor stool. fabrication of a new motor stool as per drawing. installation and alignment of the new stool and motor, followed by proper coupling. 2.fabrication and installation of plough feeder for conveyor c-72 fabrication and installation of a new plough feeder on conveyor c-72 for diversion of sinter material to the sinter ground storage yard. the plough feeder shall be fabricated and installed as per drawing and site instructions, including all necessary structural supports, fittings, and alignment. the above-mentioned works will be considered and measured as one (01) activity unit. labour,service & like charges % : 100.00 supply comp % : 0.00
Tender For auction sale of depot non ferrous scrap - lot no.p.nfa-1.bin no- 2/a ,7/a & ground floor at near bin -37.exmp.06.2026-27.03 description- scrap aluminium with iron attachment, and other aluminium casting, field coil, lamp caps, aluminium boring etc. our offer: a) scrap aluminium with or without iron attachment. such as- scrap aluminium cylinder for tap changer, aluminium number plate, aluminium feeder wire, steady arm, anti wind clamp, wiper motor, bus bar connector (aluminium), part of filter element of emu motor coaches, compressor & air dryer spares, horn, gauge cover, piston sub assembly, and other aluminium misc.as in the lot which are kept in bin no-2/a & ground floor of near bin 37. qty= 1929 kgs. b) scrap aluminium rear & front cover with or without rubber and grease attachment. in bin no- 7/a . qty- 2462 kgs. loading will be done by purchaser's own arrangment.
Tender For repair and renovation (civil and electrical) of 06 nos. d-ii qtrs. at ag doranda ranchi. (sh lifting and lowering of submersiblepumpmotorset change of flat submersible cable and column pipe)
Tender For maintenance of electrical and mechanical installation in non residential building at pag office doranda ranchi during 2026-27. (sh repairing of submersiblepumpmotorset and other miscellaneous work)