Latest turbine rotor Tenders | Government turbine rotor Tenders

CTN :37787292

15 Nov, 2024 10.74 Lacs

Uttara Kannada - Karnataka

Tender For bid to ras custom bid for services - undertaking defect rectification on tbu 3 4 and 5 onboard ins vikramaditya - 1) measure and record in log book the radial and axial position of turbo compressor and steam turbine rotors., 2) measure the radial clearance between ring and blades of gas turbine. check the values of change of clearances, comparing them with the normal permissible ones specified in tbu logbook/ehs and record the reading. reference also to be taken from the last readings taken in nr- 21, 3) repairs deformed labyrinths/baffle strips and restore the clearances as per rtds., 4) removal of scorings marks on journals of compressor rotor and restore the clearances as per rtds-

Central Government/Public Sector

CTN :38005126

18 Nov, 2024 45.72 Lacs

Mundra - Gujarat

Tender For corrigendum : provn of 02 in nos bore wells alongwith associated items at icgs mundra - material and labour for drilling of 02 nos pilot/trial bore by direct rotary rig method including all t&p through any kind of starta (soil, kankar, boulder or soft or hard rock) down up to 150 m depth below ground level by using suitable drill bit according to levering of casing pipe including the cost of mud pit, channels, etc and disposal of soil obtained to a distance not exc. 1 km away complete all as specified. note:- (i) the drilling shall be continued up to specified depth and in case sticky clay occurs in between the drilling must be stopped and hydrologist of gws & sb shall be contacted & eggr-in-charge shall be informed.(ii)cost of this consultant shall be borne by contractor (iii) taking the samples from the bore well cutting for every 3 meter interval and every change in strata if less than 3meter. (iv) preparation of litho logs based on these samples.(v) drill time log to be prepared and prescribed., (vi) aquifer performance tests at constant discharge with draw down and recovery reading.(vii) after completion of pilot bore, the contractor shall have to arrange for electro eater logging test of each bore.(viii) contractor have also produced bore well water test report for drinking water parameters before levering of motor and pump.(note:- if water quality not found fit for domestic purpose use then all other connected items of trial bore will not be executed.) , supply assembling, jointing, lowering and fixing in the bore hole pvc casing pipe of nominal dia 315 mm (medium well) ,10 kg/cm2 working pressure, confirming to is 4985-2000 including providing pea gravel of 8 mm to 4.6mm size for packing around the casing/slotted pipe in bore well all as specified and directed. make: astral/ashirwad/ajay/sfmc, all as per item no 2.00 above but slotted pipe. , supply, assembling, jointing, lowering lead free pvc column pipes of nominal dia 65 mm, od 75 mm (min), non toxic, pressure 16 kg/cm2 with and including top and bottom adaptor (ss) and accessories like epdm ring and double ss stud all as spd and directed by engineer-in-charge. make: astral/ashirwad/ajay/sfmc, development of tube well with compressed air by means of air compressor of suitable capacity not less than 300 cfm and over pumping using suitable capacity pump to make available water free from turbidity complete all as specified and directed by engineer-in-charge., m & l for conducting yield test for the bore well by continuously pumping for 24 hours by using a submersible pump set to determine safe pumping yield and produced water test report of samples which is collect every hour complete as directed by the engineer-in-charge. [ all arrangements for yield test shall be made by contractor and cost for the same borne by contractor ], supply and fix ms reducer, bail plug, top cover made of 3mm thick ms plate for bore well in two half sections having a hole of 75 mm bore in centre to accommodate pvc pipe and submersible cable suitable for fixing to the pvc casing pipe top, electric logging and simple strata box including provision of 2 sets of ms clamps made of 50x6mm ms flat including nuts, bolts, etc. including one coat of epoxy primer and two coats of epoxy paint wherever necessary complete all as specified and directed by engineer-in-charge., supply, install, test and commissioning of submersible pump stainless steel body electric driven with submersible motor, water lubricate, 3 phase, 10.0hp (appx) 415 volts, 50 hz with suitable submersible electric motor suitable for discharge of 2 liters per second against total head of 125m in the bore complete all as specified and directed by the engineer-in-charge. [ note : column pipe, submersible cable and control gear will be measured and paid separately]. [make: kirloskar / crompton / ksb], supply, install, test and commissioning of submersible pump stainless steel body electric driven with submersible motor, wa

State Government

CTN :38142319

02 Dec, 2024 14.80 Lacs

Korba - Chhattisgarh

Tender For transportation of hp module (hp turbine rotor & casing in assembled condition) and ip rotor & inner casing from htps, korba west to bhel bhopal works.

Central Government / Public Sector

CTN :38162720

19 Nov, 2024 NA

Panipat - Haryana

Tender For providing of custom bid for services - rprc242417 refurbishment and hsb of turbine rotor of oldwgc of rfccu unit at panipat refinery

CTN :36133144

26 Nov, 2024 NA

Leh - Jammu And Kashmir

Tender For corrigendum : supply of wss water supply scheme ppr pipe pn 20 sdr6 3 layer with outer dia 50mm , ppr pipe pn 20 sdr6 3 layer with outer dia 40mm , ppr pipe pn 20 sdr6 3 layer with outer dia 32mm , 50mm gate valve , 40mm dia gate valve , reflex bypass valve , 50mm dia socket , 50mm tee , 50mm dia elbow 90 degree , 50mm dia union , 40mm dia socket , 40mm dia elbow 90 degree , 40mm dia union , 40mm tee , 50mm tank nipple , 40mm tank nipple , 50 by 40mm reducer socket , puf water tank 2000 ltrs , 5 hp motor pump centrifugal pump -

CTN :38110589

20 Nov, 2024 NA

Adra - West Bengal

Tender For supply , testing, and commissioning of 10 hp 8 stage submersible pump with motor suitable for 150mm bore ,outlet dia -2.5inch, total head - 135 mtr, discharge at 70 mtr 380 lpm with one number he avy duty reducer socket 3"x2.5" ..make- kirloskar [ warranty period: 30 months after the date of deliver y ]

CTN :37707500

13 Nov, 2024 75.61 Lacs

Ganganagar - Rajasthan

Tender For corrigendum : tn-mm-2004 supply of hs and ls couplings and their spares for tube mill bbd 4772 at sstps suratgarh - supply items, hs coupling type lgf-685 v, nstd make rathi for ball tube mill bbd 4772 along with grid spring, horizontal cover with nut bolts and washer in fb and kw motor side 160mm;reducer side 140 mm(coupling between main motor and main reducer), nut bolts and washer for hs coupling between main motor and main reducer type lgf-685 v, nstd make rathi for ball tube mill bbd 4772 along with grid springs (one set consist of complete set of fasteners for one complete assembly), ls flexible geared coupling with fasteners as per drawing for ball tube mill bbd 4772(lgf-115) nstd, set of fasteners(bolt, nut & washers) for ls flexible geared coupling lfg-115) nstd as per drawing for ball tube mill bbd-4772(one set consist of complete set of fasteners for one complete assembly)

CTN :37723747

15 Nov, 2024 NA

Delhi - Delhi

Tender For corrigendum : procurement of 26 lines of lltr spares - emi filter 3ph 4w-200 amps , cable assembly p22 j22 p2 j2 , cable assembly p21 j21 p1 j1 , cable assembly p26 j26 p55 j55 , cable assembly p27 j27 p53 j53 , w14 ethernet cable , w27 cable , vent ducts , temperature and humidity sensor sxx probe , power cable from radar energy system to radar 50m , sfp transceiver 1611nm , display , fuse 6.3a , fuse 0.4a , fuse 2 a , fuse 1.6a , contact , motor reducer assy , isda2 module int sigma delta , raising assy optical fiber ip rating 67 , fuse 80v-30a , fuse 80v-20a , transceiver sfp 1490nm , transceiver sfp 1570nm , transceiver sfp 1610nm , transceiver sfp 1530nm -

CTN :37587934

18 Nov, 2024 NA

Delhi - Delhi

Tender For supply of spares of zsu 23mm schilka weapon system - spares of 23 mm schilka weapon system, imb-rus-slka-0458packing ring, imb-rus-slka-0468chain (for manual retraction mechanism fig-6-5/5), imb-rus-slka-0477locking washer (elevation mechanism fig-3-35/18), rus-slka-04-15-2a10main shaft, rus-slka-04-26-2a10spring (training reducer fig 3-26/32), rus-slka-05-26-2a10adjusting ring (worm reducer fig 3-33/6), rus-slka-09-15-2a10bushing (hydraulic motor attachment fig-2-30/40), rus-slka-09-20-2a10sliding block (hydraulic motor attachment fig 3-30/36), rus-slka-09-2014-2a10 or 09-19/2a10shifting fork (hydraulic motor attachment file 08/10/309), rus-slka-10-1a-2a7recoil buffer body (left hand recoil buffer assembly), rus-slka-10-3-2a14spring (recoil buffer fig 2-22/3), rus-slka-10-8-2a14lock pin (recoil buffer fig 2-22/7), rus-slka-13-57-2a10spring (manual retraction mechanism fig 6-5/32), rus-slka-14-207-2a10eccentric bushing (fig 3-39/2), rus-slka-1-9/2a7munion nut, rus-slka-202ball bearing (elevation mechanism fig 3-36), rus-slka-2-31-2a7barrel lock (fig 2-10/5), rus-slka-2-44-2a14rebound piece pin (receiver assembly fig 2-6/7), rus-slka-2c-35atwin pressure indicator (pneumatic retracting system fig 6-1), rus-slka-4-2-2a14firing pin (breech block assembly fig 2-14/1), rus-slka-7-55-2a7transmitter lever spring (fig-2-19/11), rus-slka-7-88-2a7disengaging lever spring (electric trigger mechanism fig 2-19/21), rus-slka-assy-20-121-2a10minlet hoses assembly (fig 5-1/4), rus-slka-assy-20-220inlet hose assembly (fig 5-2/14), rus-slka-assy-20-27-2a10outlet hose assembly (fig 5-2/13), rus-slka-assy-20-526-2a10outlet hose assembly (fig 5-2/13), rus-slka-assy-2-2a7receiver assembly right hand (fig 2-4/10), slk-assy-2a-2a7receiver assembly left hand, rus-slka-assy-38-45appliance for holding parts, rus-slka-assy-7-2a7electric trigger mechanism assembly (fig 2-19), rus-slka-assy-7-6-2a7transmitter push rod assembly (fig 2-19/23), rus-slka-assy-7-8-2a7marmoured hose assembly (electric trigger mechanism fig 2-19/51), rus-slka-edp-300high pressure transmitter (pneumatic retracting system fig 6-1), rus-slka-edu-150low pressure transmitter (pneumatic retracting system (fig 6-1), rus-slka-sb-32ammunition belt loading and unloading machine, slka-7-51m-2a7trigger block (fig 2-19/12), slk-assy-13-16/2a10manual retraction handle assembly, slk-assy-19-75solenoid operated air valve cable, slk-sb-2-2u7cleaning rod brush, slk-2-49-2a14feed lever pin, slk-2-42-2a14auto safety base pin, slk-6-2a14safety pin, slk-2-4-2a14auto safety pin, slk-assy-1-2a7barrel assy, slk-assy-1-2a7mbarrel assy, rus-slka-assy-11-2a7mcable no 77 assembly, rus-slka-1-18-2a7nipple washer, rus-slka-20-2052-2a10gasket, rus-slka-22-9-p-303drift dia 4x40, rus-slka-assy-2-2107cleaning rod brush, rus-slka-sb-38-15device for holding parts, rus-slka-1-20-2a7flash eliminator, rus-slka-8-7-2a14mrear cartridge stop pin, lv2/slk-38-50-2a10gun & link hook, z3-slk/ bd7. 823. 002drift pin 1.5mm gen purpose, rus/slka-assy-7-2a7electric trigger mechnism assy (cable fixed in mechanism), nkerd with cable for right gun (b ver), rus/slka-assy-7-2a7m & slk-sb-11electric trigger mechanism assy & cable no 77, nkerd with cable for right gun (m ver), m2-slk sb 3 2107drift for cart chember, m2-rus-slka-97-zu2scourer, lv2/slk-5-6wedge, m2-rus-slka-sb-4-zu2hammer gun, m2-rus-slka-5drift dia 2, lv2/slk-6-2a7-10drift dia 3, z3-slk/vl-200electric loading machine, m2-rus-slka-assy-23-2a10loading turf for lh gun (rh tray), m2-rus-slka-assy-24-2a10loading turf for lh gun (rh tray), rus/slka assy-23-2a10right hand tray, rus/slka assy-24-2a10left hand tray, m2-rus-slka-assy-31-2a-amlink deflector, rus-slka-sb6-2yu2cleaning rod assy, m2/rus/slk-1-82a14muzzle cover locking pin, z3-slk-km-600dvcontractor km-600dv, lv7/slk-kpp-2relay box, lv2-slk-tem-15elctric gauge with pickup, lv2/slk gost 949-57air cylinder 10.1501, lv2-slk-575-10-22-001ahydropneumatic accululator assy, lv2-slk-575-10-22-032afuel pipe line, lv2

CTN :37621922

21 Nov, 2024 NA

Delhi - Delhi

Tender For procurement of spares for an-32 aircraft - bearing, ball bearing, ball bearing, terminal block, resistor unit, frequency synthesizer, relay, panel, contactor (v), ramp sil bridges, processor tray wit fan 28v, upper casing, bracket, column speaker, nozzle, damper assy, ball bearing, lower casing, bronze diaphragh dia 46, diaphragm, rudder control unit, flow restrictor, safety harness, extractor parachute system mount, shroud, armature, reducer (v), cable linkkage, one piece seat (stb frame 09 to 10), antenna (glide slope), filter-desiccator, remote control, safety harness restraint mechanism, eyebrow window glass panel (rh), ramp extension, oxygen mask with mask face piece, port main lg door, spray manifold, sill lock cylinder, crew cabin lock, elevator rh, actuator for ga163t/16 valve manual control, display unit, elevator trim tab control and gust locks control mechanism, lh ai-20d engine control linkage in engine nacelle, control rod, p/s fail warning un, angular velocity trans, elevator (lh), inboard flap main section (lh), electric motor, end fitting, elevator, left, windshield wiper components, bottom emergency exit door, slat segment 2, rh, slat segment, lh, rip cords retraction mechanized system, emergency braking handle (lh), bottom emergency exit hatch

Turbine Rotor Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

State Government

Central Government / Public Sector