Latest water cum foam monitor Tenders | Government water cum foam monitor Tenders

State Government

CTN :45279412

08 Jun, 2026 25.91 Lacs

Umaria - Madhya Pradesh

Tender For procurement of water cum foam monitor mounted on trolley at sgtps, mppgcl birsinghpur

Central Government/Public Sector

CTN :45264914

30 May, 2026 NA

Bhopal - Madhya Pradesh

Tender For supply of 2.2 kw ac crane drive , 5.5 kw ac crane drive , 11.0 kw ac crane drive , 22.0 kw ac crane drive , 37.0 kw ac crane drive , 55.0 kw ac crane drive , 75.0 kw ac crane drive 3 phase, digital ac crane drive 2.2 kw, ac drive should be suitable for heavy duty operation of 2.2 kw. offered ac drive should be suitable for crane-hoist operation. if, separate software required for crane application, it must be clubbed with supply of material. ac input voltage: 380 to 480v ac 10%, 3 phase, 3 wire, 50 hz; mode of control: bi-directional fully controlled 3-phase ac; speed regulation: 1% of base speed; braking: suitable dynamic braking resistance and chopper unit (external or in-built); acceleration time: 0.1 to 1000s or better; deacceleration time: 0.1 to 1000s or better; overload: 150%-1min, 200%-3.0s; ambient temperature: 0 to 50 c (derating shall not occur below 50 c. in the event that derating occurs below 50 c, the supplier shall provide a higher-rated drive to match the requirement); rated current at 50 c: min. current should be 5.5 amps at 50 c; high starting torque at low speed: 200% starting torque at 0.3 hz; two analog inputs: two nos. analog inputs having signal voltages of 0 to 10 vdc or 4 to 20 ma (configurable); two analog outputs: two nos. analog outputs having signal voltages of 0 to +/-10 vdc or 4 to 20 ma (configurable); six digital inputs: pnp/npn; one relay output: with short-circuit and overload protection; two digital outputs: with short- circuit and overload protection; brake release signals: outputs braking signals based on inverter operating conditions to prevent cargo bed rollback and overrunning; load adaptive control: when the actual load level is lower than the configured load level, the system can be operated at a ratio-multiplied speed (in terms of the configured frequency), resulting in significantly better efficiency; load ) /bid number : gem/2026/b/7563714 * /dated: 20-05-2026 & & / bid document 1 / 29 frequency), resulting in significantly better efficiency; load limiter: maintains the safety and rescuability of suspended loads by stopping when excessive torque is detected and by allowing operation only in the direction opposite to that in which the excessive load was detected; cooling capacity degradation alarm: detects and displays cooling capacity drop due to cooling fin clogging caused by dust and cooling fan airflow reduction; igbt life expectancy forecasting: estimates the power cycle life expectancy of the main circuit s igbt semiconductor device temperature due to frequent acceleration and deceleration stoppages, and displays the estimate before the design life is reached; protection: it must have all standard protections like stall protection, instantaneous power failure, single phasing, over voltage, under voltage, over current, inverter overload, thermal overload etc; display console: it must have alpha numeric display console for programming of drive, fault display and operating condition; dynamic qr code: it must have dynamic qr code for trouble shooting; tuning facility: it must have auto tuning facility. this must enable perfect matching of motor coupled to load with regards to optimum acceleration time, deceleration time, speed regulation etc; drive programming software: suitable drive programming software along with necessary connecting cable and adapter for connection with laptop and drive should be provided to get online with the offered drive (laptop not in scope); automatic voltage regulation: it must have automatic voltage regulation function to maintain high starting torque even at reduced voltage; regenerative option: it must be capable of regenerative operation; communication protocol: modbus (rtu/serial) or ethernet (tcp/ip); make of drives: fuji- electric/yasakawa/schneider/abb only; suitable dynamic breaking resistance unit of 60% wattage rating of drive, however the value of resistance is to be decided by manufacturer as per their technical manual for crane-ho

CTN :44652315

21 May, 2026 NA

Ernakulam - Kerala

Tender For corrigendum : tender for supply of o ring an 77 50d7 , flex master con for dia 88.9-epdm , loctite 307 , supply card ae 24/15 , paper insert , nitrile cord d7 1123l , joint , o ring ms29513/356 60c7 , injector body , glass bulb 28vdc 40 ma set of 10 , o ring ms29513/355 60c7 , illuminated red push button 2no , shim , piston , gasket for exh , frequency divider , loctite 549 , shim , metallic gasket , spool valve air operated 2 pilots location 13 , shim for gov control , rubber compensating sleeve , o ring an69 60c7 , flexible manifold sealing joint , joint type c with limiter , connecting straub metal grip d42.4 epdm , switch 3 pos. 1tc auto 2tc , corrugated joint , flexible hose for sea water pump suction , elastic - mounts , o ring an61 60c7 , exhaust manifold lag , pressure switch 0.35 to 5 bar , tightening collar , gasket/joint , spool valve air operated 2 pilots location 15 , o ring an21 nse 6.5 60c7 , loctite 270 , set bolt-m12x35-10.9 , bush , piston ring compression ring , frequency divider-turbo speed , b.s.ring c20 , 60c7 , fuel filter incl 2filtering elem7915427000 , snap ring , bearing temp alarm card aip card , pressure transmitter , self locking nut , stud , set of gasket for hyd motor and diversion sect. , spring , o ring for gf600 filt.no.2090p , expanding plug , frequency preamplifier t/c speed , stand tube for glacier filter gf600 11 , joint , joint , temperature sensor , o ring 5x589 viton 20312 , oval gasket bbc supply , cable for connecting rod sensor , o ring , o-ring ann74 nse6.5 60c7 , fresh water pressure gauge 0-6 , flash card 64k , cap nut , collar split , bearings individual alarm card , o ring , air disributor disc , rubber compensating sleeve dn150 pn16 lf130 , gasket for injector , tie rod , clamping collar , distributor iso electro pneumatic/electric , air distributor body , supply card ae 24/24 , v belt a54 , exhaust temperature sensor , water inlet flange , box spanner , electro distributor with spring return , banjo bolt , supply card 24 vdc / 15vdc , threaded bush - fuel feed pump , distributor iso electro pneumatic/spring , o ring an22 60c7 , snep nut binx nut hm10 , tappet , links , disc spring washer , or pneumatic module , copper washer 8x22x1.5

CTN :45113431

22 May, 2026 NA

Kokrajhar - Assam

Tender For corrigendum : supply of double hydrant posts , jet nozzle , water jet monitor , water cum foam monitor , fire hydrant hoses , fire hose box , universal nozzle , fog nozzle , water curtain nozzle , spray nozzle , branch pipe - 63mm dia , sand bucket

CTN :45162908

22 May, 2026 NA

Kamrup - Assam

Tender For supply of 4 inch water cum foam monitor , gate valve , fire hose , fire nozzle , 4 inch flange , 4 inch gasket , studs , butterfly valve 4 inch

CTN :45063622

23 May, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For supply of 25vkoc005 c c - joint , main bolts , inner star , gfl bolts , gfl washer , clamping collar , clamp , valve for water pump , bush , fresh water cooler relience make , spare part kit for fw/sw heat exchanger , starting air conn.inlet , engine inlet pressure connection , governor speed setting air inlet connection , rack position limiter , fuel rack indicator , pressure transmitter p5r-4bar-4-20-1/2-pe , pitch indicator 0-20ma , pl96 , relay 4no-nc 24v dc , solenoid valve (nomo-24 vdc) , cd3 cable (5mm) , safeties reset push button , emerg. stop push button , scanner thermocouple pcb , display pcb , press.sw. (item no.17 of engraved ckt) , pressure regulator , pneu p.b. pneu return red , pneu. switch , s w engine driven pump assembly , stud m12 40 30n j12 nse1 181 , oring an7 31b6 , o ring 151i d 3d nse6.531 21a7 , filtering unit , viton oil seal 15x30x10 , fuel filter element , protect cyl head tie rod , injector body extractor , inj.pump and pump head extractor , flexible hoses , high pressure hand pump , bearing unit , bush sealing , bolt-connecting rod , o ring , thrust -stopper , top spring collar (bar) , bottom spring collar , dunb bushes 25-25 du , shaft , seal bearing housing , coupling pin , sealing joint , bs ring , type c30 , nse 6.51 , 20 , paper insert , o ring , needle roller bearing , rucompensation probe for exh. pyrometric duct , hydraulic jack for cylinder head , tool valve guide extractor , tool cylinder head test pressure , flex hose for hydraulic tool , high pressure hand pump , tee connection , safety valve , water pump impeller , scraper ring , round gasket , flexible hose for air , spare gauge glass 583 , sealing bush , piston ring , safety ring for abb vtr251-2p t/c , gfl washer , pressure switch(p 16 bars) , pressure switch(p 19 bars) , normal stop electro distributor , circuit selector , tt-314 sensor for main engine fresh water temperature , 25 pin sub d female connector , pressure gauge forbes marsh 100ss , ss316 0-4 bar glyf fil , pressure gauge forbes marsh ss316 0-40 bar glyf fil , pressure switch for s/by pp (range 0-4 bar) , pneumatic distributor pneu/pneu , sph card (sph) , lub oil pressure safety , pressure switch-1 to 10 bar , bearings individual alarm card (aip) , convertor module t454 t456 lub oil temp , svae - over speed cards , engine speed indicator 0-1250 rpm 96x96 , cock with filter , distributor iso 541 pneumatic spring , distributor iso 541 pneumatic/spring , iso1 distributor pneu.control/pneu.return , switch 3 pos. (1tc , auto , 2tc) , engine control unit (ecu) , gasket , fuel pipe m14xm14b , parallel , 750l , 9.0 i.d. , sae 100 r6 , booster servo motors with connectors , meta flex gasket , meta flex gasket , meta flex gasket , fuse 0.5a , link cable pc/tsx plc length -3mtr , oil pressure security card (sphem) , speed raise lower actuator 2no contacts , touch screen color display unit , 3 position switch , fuel pipe(return) m12x1.5 male plugxm14 x1.5 banjo(700mm) , universal crimping tool , oil mist detector , time delay relay (off delay) , pyrometric duct bank a

CTN :45063614

23 May, 2026 NA

Bankura - West Bengal

Tender For supply of 25vkoc001 c c - injector connection assly , injector holding flange assly. , pyrometric duct , expansion below , electronic governor-actuator , flex master con for dia 88.9-epdm , compensation sensor for exh.pyrometric duct , disc spring , piston ring , air valve , set of spare gasket & o rings , o ring dia 3 x dia 290 , o ring dia 3 x dia 260 , special seal , set of spares for abb vtc254 turbocharger , spare part kit for fw/sw heat exchanger , pt 100 converter with two threshold , ferquency preamplifier-engine speed , supply board , flash 64k card , communication module , pcmcia card , 16 analog input card , rtd input filed module , filed communication module , fuse 4a gg 10 38 , thermistor protection relay(aux415v ac) , injecting piping assly , set of seal for glacier filter , plug no4 , 25 cts , pyrometric duct bank b , expansion bellow , floating bush(te) , oil seal (190x160x15) , d/row sph rlr brg (100x165x52) , d/row sph rlr brg (120x180x46) , cap screw , portable temperature simulator 0-600 deg celcius , disc spring , release spring , gt2 coalescer filter panel , seal tape roll , barring gear assly - gali , type - gd , loctite 480 , crankcase pressure measurement assly , o ring , drilled cap plug - dn 12 , connecting straub metal grip d42 4 epdm , adjusting screw , injector tappet , gasket , injection pipe , o ring , p2-p4 by pass valve-gachot-dn125 , seal ring chord , expansion bellow , metallic gasket , cartridge , v band clamping , lub oil filling connection , rubber compensator , rubber compensator g0125 x 130 x 016 hks-g nbr gr deb , rubber compensator g0100 x 130 x 016 hks-g nbr gr deb , clamping collar , expansion bellows , metallic joint , o ring an 30 , 21a7 , gasket for lub oilcooler (nopv) , channel plate gasket , engine inlet thermostic valve , o ring , disc spring washer dia.56xdia.28.5x3 , disc spring washer dia.40xdia.21.5x2 , temperature sensor , silencer pads (fx4000) , lid seal for fx4000 , hex bolt , hex bolt , time delay relay(on delay) , elelctrical connnection laptop-engine controller , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , flex hose , repair kit for gali starter , set of seal for gali starter , solenoid valve-24v , main bearing assly , gasket , gasket , o ring , gasket , seal , impeller , 2 lips oil seal , bearing , mechanical seal eagle , o ring , bearing , cap plug , injector sleeve , o rind- ms 29513/238 , v 75 e , o ring - kalrez , inlet valve guide , gasket exhaust manifod , valve seat metallic ring , inlet valve , exhaust valve , rocker arm bush , metallic joint , rocker cover screw , piston ring - top - chrome , ceramique , piston ring - compression-g3-chrome , piston , gasket , set of gasket for hyd. motor , connecting axiflex metal gripd168.3 , epdm , gasket , service tool kit for oil mist detector , exhaust temperature sensor , o ring - ms29513/230 , 60c7 , o ring an26 , 60c7 , nozzle assly -9 x 0.52 x 148 , helicoflex joint hn100 , d17.4 1.8mm , sea water pump , joint type c with limiter , metallic joint , tc speed sensor , gasket rc , o ring d54 , 50x3 v70d , o ring an29 , 21a7 , gasket , hose , metallic joint , set of spares for air valve and actuator , set of spares for p2/p4 bypass valve , actuator service kit , fresh water temp sensor (rtd) , coupling assly cw , connecting cable (unitel way) , analog input field module type 170aaio3000+slave 170fnt11001 , lamp , hooter (electronic) , power switch , fuse 10x38 2a gg , pt 100 converter with two threshold , solenoid valve-safety stop , power fuse , 32a , rsp bearing safety card , icm safety stop card (4 channel) , frequency preamplifier (engine speed) , human machine interface , main bearing temp probe , connecting rod bearing temp probe , washer bsf , ring for casing , bushing

CTN :43695606

09 Apr, 2026 NA

Kokrajhar - Assam

Tender For bid to ras corrigendum : supply of 4. 5kg co2 fire extinguisher , 9kg dcp fire extinguisher , 75kg dcp fire extinguisher , dcp powder in kgs , 200gm co2 cartridge , 2kg co2 catridge , water gel blanket , scba , fire proximity suit , folding stretcher with blanket , manual resuscitator , low temp protective clothing for lpg emergency , emergency trolley , hand operated siren , safety shoes , safety net , safety helmet , low temp hand gloves , red and green flag sets , wind sock , safety goggles , safety mask , safety belt , ear muff , double hydrant posts , jet nozzle , water jet monitor , water cum foam monitor , fire hydrant hoses , fire hose box , universal nozzle , fog nozzle , water curtain nozzle , spray nozzle , branch pipe - 63mm dia , sand bucket , supply of flp torch , supply of hand held metal detector , multizone door frame metal detector , sup under veh. search mirror

CTN :44452309

06 Apr, 2026 NA

Kodinar - Gujarat

Tender For corrigendum : supply of high expansion foam generator unit , portable water cum foam monitor , stored pressure type 06kg map 90% portable fire extinguishers