Get complete information related to latest Wire Lead Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Wire Lead Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Wire Lead Tenders.
Tender For procurement and installation of different instruments for instrumentation of earth dam and spillway in deo irrigation project for the year 2025. - supply of fiberglass reinforced plastic (frp) make universal enterprises an improved venturi plate conformed to is: 9108 for accurate measurement of water flowing through channels comprising of masonry construction provided with pre-fabricated glass fiber lining on both sides, a side chamber provided in one side masonry wall of the said flume on the upstream side, a pipe provided at the bottom of the chamber connecting the said chamber with the water flowing through the notch, a float means provided in the said chamber, enabling recording the rising or falling level of water in the said chamber such as a scale provided in the said chamber, moulded engraved gauge marking in lit/sec and also in centimeter including moulded and engraved discharge table, capacity marking, flow direction, m.s pipe stiffeners, hold fasts, sand treatment on the backside of plate but excluding gst as per the instruction of engineer-in-charge etc. complete, inside spillway foundation gallery - 15 lit./sec. v-notch, seepage drain - 90 lit./sec. v-notch, calibration marks:- supply of polymers composites improved calibration marks make universal enterprises with contact molding process, both side finish, m.s. strip embedded inside, engraved and molded marking for bands and figures covered with radium and covered with two coats of polyurethane for surface protection with marking in reduced levels, sill, fsl, frl, mwl but excluding gst as per the instruction of engineer-in-charge etc. complete, supply vw up-lift pressure meter provision for connected to das make : aimil ltd. uplift pressure meters are used for measuring and recording of uplift pressures acting in foundations of concrete/masonry dams. vibrating wire type uplift pressure meter : range: 0.2 mpa to 5.0 mpa./7ksc accuracy: 0.5 -1 % fs. temp limit: - 10 to 70 deg c. coil resistance: 140 - 160 ohm thermistor: ysi-44005 or equivalent. material: stainless steel cable: 1m, 4-core borehole for uplift pressure meter at foundation gallery (inside spillway) should be straight from foundation level and clear. proposed location : inside spillway foundation gallery in overflow section: 7 no. non overflow section: 2 no. purpose: uplift water pressure measurement. (but excluding gst), supply automatic seepage measuring system make : aimil ltd / sysgeo italy or equivalent vibrating wire water leakage measuring systems are used for measuring water leakage and flow in dam galleries by installing v notch weir coupled with vibrating wire sensor for remote monitoring of water leakage. sensor type: sensor : vibrating wire precision water level sensor range: 300mm resolution: 0.025%fs material : stainless steel excitation : sweep or pluck assembly: v.w. type sensors enclosed in an environmental proof fibre glass box. splicing kit & adhesive required accessories. proposed location : inside spillway foundation gallery: 1 no. toe drain: 1 no. (drainage outlet) purpose: seepage water measurement in liter per second (but excluding gst), supply data logger or data acquisition system aimil make dt85g with cem20 or ace s korea analog channels 16 analog input channels each channel is independent and supports: one isolated 3-wire or 4-wire input, or two isolated 2-wire inputs, or three common referenced 2-wire inputs. expansion requires optional cem20 sampling integrates over 50/60hz line period for accuracy and noise rejection maximum sample speed: 40hz effective resolution: 18 bits linearity: 0.01% common mode rejection: >90db line series mode rejection: >35db vibrating wire frequency range: 500 to 5khz coil resistance: 50 to 200 stimulation method: single pulse pluc digital channels 8 bi-directional channels input type: 8 logic level (max 20/30v) output type: 4 with open drain fet(max: 30v, 100ma) 4 with logic output alarms power supply , sim card will be in your scope. propo
Tender For corrigendum : supply electrical consumable items for emd-3 bop & lighting section. - crc-226 contact cleaner in 415 ml/300 gram spray bottle., self adhesive pvc electric insulation tape rolls with isi mark size 1.80 cm width x 7.5 mtr length x 0.125 mm thickness, of red colour, test leads (probes) for digital multimeter, ht pvc insulation tape size 0.18 mm x25 mm x 65 mtr length, led torch, pvc twin wire 2.5mm sqr., flexible wire 2-core, 2.5 sqmm, copper flexible wire 3 cx2.5 sqmm ,1.1 kv, flat cable 3 corex4 sqmm with copper conductor for submersible motor, 1.1kv,multi stranded anealed tinned copper,epr insulated,extruded pcp sheath flexible cable size 4cx4 sqmm, wolf make air blower, vernier caliper "mitutoyo" make,size- 0- 300 mm, screw driver (tester) taparia product no:818.special with neon bulb,generally confirming to is 5579-1985 grade - ii, yellow handle,, tester type screw driver (special with neon bulb) generally confirm to is-5579-1985, grade: ii, handle- yellow colour, taparia product code-813, overall length 130 mm, combination plier, insulated with thick c.a. sleeve with joint cutter, generally confirming to is 3650-1981, product no. 1621-8., double ended fix spanner sets contant-6x7,8x9,10x11,12x13,14x15,16x17,18x19,20x22,21x23,24x27,25x28,30x32mm(12 nos),product no:14 (b) dep12, double ended ring spanners sets, ,contents- 6x7 , 8x 9, 10x11, 12x13, 14x15. 16x17 , 18x19, 20x22 , 21x23, 24x27, 25x28, 30x32 mm., socket set 1/4 " square drive(sockets-4,4.5,5,5.5,6,7,8,10,11,12,13,141/4,t20,t25,t30,t40,accessories-a733,a743,a753,a773,a703,a715), allen key set mm size (09 piece) 1.5,2,2.5,3,4,5,6,8,10 mm, bolt cutter, taperia make, length- 300mm, product no-bc-12, hydraulic hand operated crimping tool capacity : 50 to 1000 sq mm with changable hexagonal dies sets ,suitable for cu / al cable, crimping tools, capacity: 6 mm2 to 50 mm2., digital clamp on meter lcd display with backlight, 3-3/4 digit., din rail mounting channels, mcb 3 phase,4 pole, 63 amp 440 v ac 50 hz 10 ka
Tender For corrigendum : supply of spares for laundry machine - electronic thermostat w,wire lm353m compatible to machine model- hm270 and hm490, make- ipso , seal assembly grommet for temperature sensor compatible to machine model- hm270, hm490 and hf234, make- ipso , speed detector xs4p12pa340 compatible to machine model- hm270, hm490 and hf234, make- ipso , main print board ps40 230v compatible to machine model- hm270 and hm490, make- ipso , keyboard ps40 220v compatible to machine model- hm270 and hm490, make- ipso , water level switch pressure-1 compatible to machine modelhm270, hm490 and hf234, make- ipso , kit drain valve w,bracket mdb 300 no compatible to machine modelhm270, hm490 and hf234, make- ipso , tilt switch compatible to machine model- hm270 and hm490, makeipso , water inlet valve compatible to machine modelhm270 and hm490, make- ipso , electrical door lock pkg ele-div-0077 compatible to machine model- hm270 and hm490, make- ipso , computer board micro 20,frequency 230v compatible to machine model- hf234, make- ipso , eprom 27c256 pkg compatible to machine model- hf234, make- ipso , glass fuse 5x20mm f0, 5a,250v compatible to machine model- hf234, make- ipso , emergency button xb4-bs542 red with lock compatible to machine modelhf234, make- ipso , contact for emergency stop compatible to machine model- hf234, make- ipso , thermostat cygnus detector lm35 hf,ww304 compatible to machine modelhf234, make- ipso , tilt switch obl compatible to machine model- hf234, make- ipso , two way inlet valve muller30 plus 50l us-thd 220v compatible to machine modelhf234, make- ipso , solenoid inlet valve muller 220v compatible to machine model- hf234, make- ipso , two way inlet valve muller met 30 plus 50l 220v compatible to machine model- hf234, make- ipso , diaphragm for muller valve 30 plus 50 compatible to machine model- hf234, make- ipso , rotation sensor compatible to machine modeldr55, make- ipso , thermistor compatible to machine model- dr55, make- ipso , cabinet high limit thermostat compatible to machine model- dr55, make- ipso , thermostat lim 340f violet compatible to machine modeldr55, make- ipso , thermostat lim 350f blue compatible to machine model- dr55, make- ipso , air flow switch actuator compatible to machine model- dr55, make- ipso , contactor block for ess compatible to machine modeldr55, make- ipso , door switch snap spst no cherry compatible to machine model- dr55, make- ipso , lint door switch compatible to machine model- dr55, make- ipso , electronic control dx4 compatible to machine model- dr55, make- ipso , temperature sensor for electronic control dx4 compatible to machine model- dr55, make- ipso , drain pipe qui -nca - 0380 for ipso hm490 washing machine , relay board for chemical additon svs
Tender For corrigendum : supply of 415v, utilization category ac23a, 630a local isolator cabinet in sheet steel enclosure complete with 630a, 3 pole load break switch. 2. shall be with side operated handle, padlocking facility, prebreak micro switch having 1no+1nc contact. 3. micro switch contacts shall be wired to 4 sq mm tb for external termination. 4. provision of padlock system having sufficient space to lock the isolator at off position by minimum two agencies at a time. 5. complete with both power & control circuit wiring with all insulators, bus bars and control terminal blocks. 6. detachable bottom gland plate for entry of cables from bottom. 7. front door shall be hinged and inter-locked with the isolator in 'on' position. the front door should have a minimum 3 mm thickness perspex/triplex window for observation of position of contacts. 8. isolator should confirm to iec 60364 standard. 9. the dimensional drawing of the local isolator cabinet or product catalogue showing mounting arrangement of the components should be enclosed along with the offer. 10. isolator cabinet should be provided with rain canopy. 11. any isolator parts should not be made of aluminium/aluminium alloy. 12. isolator cabinet shall be metal enclosed suitable for wall fixing using 4 welded fixations, dust and vermin proof and shall be provided with degree of protection as ip-55. 13. provision for three distinct parallel busbar per phase for termination of three nos of 240 sqmm aluminum cables for incoming and two distinct busbar per phase for termination of 120 sqmm copper cable. 14. all hardware used in isolator cabinet shall be corrosion resistant. 15. minimum clearance between the live parts and detachable bottom cable gland plate shall be 400mm. 16. cabinet should be painted with alkaline resistant epoxy paint. 17. isolator cabinet shall have provision for earthing at two separate and distinct points. 18. each isolator cabinet should be supplied with panel keys., push button station specification: 1. pbs made of 2mm sheet steel enclosure with rain canopy, protection: ip-65. 2. 01 no. of green colour start pb with 1no+1nc contacts, 01 no. of red colour stop pb with 1no+1nc contacts, 01 no.of increase pb with 1no+1nc contacts <(>&<)> 01 no.of decrease pb with 1no+1nc contacts. one emergency stop push button with 1no+1nc contacts (push to lock type) shall be provided. size of each push button is of 22.5mm diameter. inscription plate for all push buttons. 3. pb shall be wired with 2.5 sq.mm. copper wire to 40 nos. serially numbered terminal blocks (tb) of elmex make having tb-5-6, 7-8, 11-12, 13-14 <(>&<)> 17-18 shorting link. 4. two nos. of cut out of size 72x72 mm for ammeter and rpm meter shall be provided. 5. 'on','off' <(>&<)> 'trip' indication led lamps in red, green <(>&<)> amber colour respectively with inscription plate to be provided. 6. all push buttons, elements, led lamps <(>&<)> cutout for ammeter <(>&<)> rpm meter shall be on the hinged door of the pb station. 7. pb station shall be weather proof, neoprene rubber gasket suitable for outdoor application. 8. 2nos. of earthing studs to be provided. 9. left side hinged door shall be provided with flexible braided copper earthing. 10. pbs shall have 04 nos. of corrosion free bracket suitable to fix on vertical surface. 11. detachable gland plate to be provided. 12. the push button shall be painted with one coat of red oxide primer <(>&<)> two coats of zinc chromate primer and finally finished with stoving enamel grey paint. 13. the push button station shall be generally in line of enclosed drawing (fig-2). 14. party to submit the drawing along with the offer for technical scrutiny.
Tender For corrigendum : supply of integration tool kit for aircraft power system - positive grip straight head screw driver set , asme b 18 point 3 standard l style hex key set , alloy steel rust proof soft metal cutting plier , chemical resistant-forged jaws- flat nose plier , chemical resistant- forged jaws- round nose plier , chemical resistant-forged jaws- long nose needle plier , wire stripper-12 to 20 gauge , wire stripper normal , ss 316l grade fine pitch components tweezers- straight , ss 316l grade fine pitch components tweezers- bent , retractable utility knife with blade , non-contact voltage tester , electrical insulation tape -red-black and blue , rohs compliant rma solder wire , solder flux -wax type , 99 point 9 percent pure isopropyl electronic grade-el grade , astm d5363 standard dimethyl acrylate high strength adhesive , premium masking solvent and paint resistant tape , integrated 94pc quarter inch and half inch socket set , cable zip ties 150mm long- pack of 100 , cable zip tie 250mm long- pack of 100 , ambidextrous scissor- length 240mm bid number/ & ( * ) : gem/2025/b/6023510 dated/ + : 27-03-2025 bid document/ 3 3 1 / 23