Tender For supply of details description of specification for 100 watt led flood light - led rating in warm)/system wattage/rated power, led luminaire conformity to 15:10322/part 5/section 5/2012 latest and 15: 16107, (part 2/sec 1):2012, photo biological safety of leds used shall be as per 15:16108/2012 (exempt grou, types of led luminave as per the 15: 161070part-2/sec-11/2012, types of led modules as per the 25: 16103(part 2)/2012, led rating/system wattage/rated power, luminaire system efficacy bumen/watt), ingress protection (ip rating) as per 1 10322 (part 1): 1982 latest, mounting brackets fincluded, warranty for free replacement (in year), input operating voltage range and frequency, automatic higher cut off voltage above 300 volt, rated voltage, ac power factor at hill load, driver efficiency lin sage), total harmonics distortion (in lage), the total circut power shall not be more than 110 percent of the valve declared, by the manufacturer, led chip efficacy, colour temperature (+500), working life for led (minimum 50,000 buming hours as per lm-80 report), coltur rendering index(cri), optic lenise materal (uv stabilued) (write na or without optic lense supply), heat sink should be die-cast aluminum along with sufficient heat sink fins to desipate heat effectively, capacitor shall be ratail for a temperature of 105 deg. ceblus or better, junction temperature, operating temperature range, operating humidity range, short circuit protection, overload protection, over voltage geutection, reverse polarity, high voltage test (1.5 kv for ane minute between napply terminats and body of the, unit), insulation resistance between earth and current carrying part, the luminaire shad be protected against surges and transients (internal), the luminaire shall be protected against surges and transients of >/1kv, (external, the luminaires casing/housing (single piece housing) shall be pressure de catted, aluminum alloy with higher thermal.conductivity, the lummaire body must be corrosion resistant epoxy powder couted, all fasteners must be of stainless steel, the entire housing (both led section and driver section) shall be dust and water proof having ip 66 protection as per 15:10322 (part 11:1987 latest, luminaries light transparency should be of toughened glass, toughened transparent glass cover thickness, toughened glass shall not get discolored shall not suffer degration due to heat and agning within warranty period, number of electronic control gest (power sanoles), driver components shall be industrial grade or above, pci shall be fre grade minimum 0.8 to 1.0 mm thick or mom, the luminaires works on single phase three wires system (phase, neutral and, earth, suitable connector shall be provided for led connection between driver output, and led, length of st marked three cors wire (shall be provided along with supply of, materiall, ught source, manufactures name and and brand on the aluminium die cast body, manufacturer's name, model number, serial number, date of manufactiare (month-year), and int number as identification mark inside each unit and the outside of each packaging box, the operation characteristics voltage and power be marked inside of each led, system must have emi/emc compliance as applicable (test reports shall be furnish on demand by buyer/consignee)
Tender For design, engineering, procurement of material, manufacture, fabrication, shop testing, packaging, loading, supply to site, shifting of materials from store to the erection site ,erection, site testing, commissioning, regular operation and maintenance of complete water chemical dosing system on boot basis for the blast furnace water recirculation systems , required for up_gradation of blast furnace no. 3 at sail, durgapur steel plant.
Tender For bid to ras corrigendum : supply of led batten (q2) , cast copper alloy screw down bib taps and stop valves for water services as per is 781 (q3) , cable trunking and ducting system for electrical installations (wiring duct) (q3) , piano type non modular domestic electrical sockets - is 1293 (q3) , non - modular piano type domestic electrical switches as per is 3854 (q3) , wire nails (q4) , wood screws (q3) , tower bolts (ferrous metals) as per is 204 (q3) , curtain pipe, sider and mounting bracket (q4) , m - seal as per is 9197 (q3) , steel pipes for water and sewage as per is 3589 (q3) , piano type non modular domestic fan regulator as per is 11037 (q3) , pvc flat cable, aluminium conductor with pvc insulation and sheath as per is 694 (q3) , gland packaging (q3) , elecric bells and accessories as per is 2268 (q3) , pvc insulated unsheathed cable with flexible conductor as per is 694 (q2) , metal alloy casting water tap with aerator (v2) (q3) , taflon tape as per is 14635 (q3) , solvent 100 ml make as per sample. , sheet glass self assembly corner shelf make shakti jaynam prayag. , angle holder insulated backlit body with brass metel parts make kinjal bajaj havelles. , brass spindle for concealed stop cock 15 mm with plunger make shakti jaynam prayag. , flush handle make as per sample. , kitchen rack of sizes 650 x 950 x mm with suitable hanging hook make shakti jaynam prayag. , short bend pipe make as per sample. , ms bolt 40 mm long 3 mm dia make as per sample. , ms nut and bolt 75 mm long 6 mm dia make as per sample. , ms nut and bolt 50 mm long 3 mm dia make as per sample. ) /bid number : gem/2025/b/6635826 * /dated: 04-09-2025 & & / bid document 1 / 39
Tender For supply of spinal needle, no. 25g, specification: a) technical specifications: quincke bevel spinal needle. transparent hub, to allow easy visualization of cerebrospinal fluid (csf). the hub should be big grooved , colourless , transparent with csf identification system (prism and magnifying lens inside the hub) for improved visualization of csf flashback needle core hub with lock to keep the surface of needle bevel joint well oriented fitted stylet to minimize tissue coring external diameter expressed in gauge and mm. for 25 g needle - 0.50 mm x 90 mm length colour code( orange) /external diameter: visible at the base of the spinal needle. components: needle, stylet and sheath. material: stainless steel needle and stylet without silicone. clear ridged polycarbonate hub. protective plastic sheath. size selected: 25g (0.50 x 90mm) black. disposable. sterile single pack initial sterilisation method: ethylene oxide gas standardisation eu mdr / ce 0318/ce 0050 compliant b) packaging and labelling: primary packaging: unit of use. one (1) spinal needle in an individual sterilised peel pack. labelling on the primary packaging: name and/or trademark of the manufacturer. manufacturer's product reference. type of product and main characteristics. if the packaging is not transparent, it must bear a diagram (preferably actual size) showing the essential parts of the product and indicating the position of the product in the packaging. the word
Tender For corrigendum : design, engineering, procurement of material, manufacture, fabrication, shop testing, packaging, loading, supply to site, shifting of materials from store to the erection site ,erection, site testing, commissioning, regular operation and maintenance of complete water chemical dosing system on boot basis for the blast furnace water recirculation systems , required for up_gradation of blast furnace no. 3 at sail, durgapur steel plant.