Tender For supply of main pinion sun gear 24 teeth en 24 , sun gear , 1st reduction pinion and gear set of helical gear box en 24 , 2nd reduction pinion and gear set of helical gear box en 24 , worm wheel for radicon gear box u-1200 , wormshaft for 1200 30 is to 1 gear box , clutch race ci , internal gear 80 t cast steel , main shaft for 50 hp en8 , brake band with liner rh or lh , tightening bar 10103d , complete clutch brake assy fitted with f , circlip for coupling shaft end part no 8737
Tender For tender for supply of esp spare d d - faa 9x45h 2x96150 2 set ring esp , faa 9x45h 2x96150 2 inner arm esp , faa 9x45h 2x96150 2 sleeve tube i esp , outer arm hammer ce , complete shaft assy for cerm , pinwheel i ee , pinwheel ii ee , outer arm hammer ee , split brg hsg assy ee , coupling ee rapping , emitting electrodes helical wire type , complete shaft for gdrm , faa 9x45h 2x96150 2 brg assy for esp
Tender For corrigendum : supply of main engine spares c c - cotter pin , plate clamping , cylinder head , cylinder cover , valve protecting cap , strip sealing , seal , gasket , gasket long seal , seal gasket , rocker arm fulcrum , outer valve cone , thrust spring , gasket , locking ring , fuel pump , pump cylinder 23 dia , ring sealing , roller , coupling sleeve , gasket , seal ring , disc , ring seal round , filter pin , ring snap , washer for injector , gasket , hexagon bolt , cock rss , screw plug , seal ring , pump assy lub oil , ring butting 14 , bearing ball deep groove , slide ring seal coal , pump cooling water , pendulam ball bearing pos 43 , fitting key pos 50 , key , gauge charging air pressure 0 to 1 kg , fuel pressure gauge , lub oil pressure gauge , ermeto bulk head screw , square gasket , cock r55 f6xr3 8cu , locking ring , ring locking , magnetic shaft , overload relay 3point8a 6point00a , bearing shell two part complete
Tender For corrigendum : supply of various size & types of rtds for 3x210 mw unit 3,4 & 5 at gandhinagar tps. - duplex rtd pt-100 as per gtps drg no ext-inst-00434 for unit no 3 and 4 id fd pa fan and motor and coal mill motor de nde bearing temperature measurement system., solid sintered tungustan carbide thermowell, length 325 mm, process conn. m 33 x 2 (m), inst conn. 1/2 inch bsp (f) for coal mill out let temperature as per drg. no.gtps/ext- imd-ii -00713, rtd duplex 3 wire pt-100 for coal mill outlet temp, od 6 mm,ss 316 sheath material insulation compact filled mgo insertion length 450 mm end connection 1/2 inch bsp head die cast aluminium ip 65.ext, pipe 150 mm., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 6 mm, sheath length: 60 mm., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 10 mm, sheath length: 300 mm straight., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 12 mm, sheath length: 100 mm straight, cable length: 15 meters., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 8 mm, sheath length: 25 mm., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 12 mm, sheath length: 250 mm straight, cable length: 20 meters., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 12 mm, sheath length: 250 mm straight, cable length: 10 meters., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 12 mm, sheath length: 350 mm straight, cable length: 10 meters., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 08 mm, sheath length: 250 mm straight, cable length: 10 meters., headless rtd(pt-100type) for f.d.fan of gtps unit no 5-d.e. /n.d.e. bearing temperature measurement,sheath dia. 8 mm, sheath length: 180 mm, process connection (male): dia:17.5mm thread:1.0 mm pitch 15 mm with adjustable sewage lock type., headless rtd (pt-100 type) for turbine,boiler and balance of plant services temp measurement,sheath dia. 5 mm, sheath length: 300 mm, process conn: -18 od x thread 1.0 mm pitch length 12mm with adj.sewage lock type, headless rtd (pt-100 type)for c/m o/l shaft low radial brg, warm shaft radial brg, o/l shaft brg temperature measurement, sheath dia.5.5 mm, sheath length: 432 mm,process connection:1/2 inch bsp (m) thread 14g with adj. sewage lock type, headless rtd for ce pump journal brg, cw pump thrust / general brg temp measurement, sheath dia.4.5mm,process onnection:1/2 inch bsp (m) with adjustable sewage lock type,sheath length:200 mm,, rtd pt-100 with thermowel element : is:2848,duplex /ungrounded t/w construction straight , material : solid tungusten carbide process conne: screwed m 33 x 2, ss316 t/w insertion lenth ( l1) 325 mm t/w od :22 mm, rtd (pt-100 type) for coal mill of gtps unit no 5-upper radial bearing temperature measurement, and dimension and material of construction as per drg. no: gtps / ext / c and i / 00775., head with plug and socket type temperature element pt-100 rtd for bearing temperature of high speed shaft coupling side, insertion length 170 mm., head with plug and socket type temperature element pt-100 rtd for lower bearing temperature of low speed shaft, range: 0-100 dec c, insertion length 290 mm., head with plug and socket type temperature element pt-100 rtd for lower bearing temperature of medium speed shaft, range: 0-100 dec c, insertion length 365 mm., head with plug and socket type temperature element pt-100 rtd for upper bearing temperature of medium speed shaft, range: 0-100 dec c, insertion length 700 mm., head with plug and socket type temperature element pt-100 rtd for upper bearing temperature of low speed shaft, range: 0-100 dec c, insertion length