Description :
Tenders for Supply Of Equipment For Mechanical Engineering Department - Supply Of Equipment For Mechanical Engineering Department, Lathe Machine :specification :bed: 2v & 2 Flat, Induction Hardened And Ground Minimum Bed Length: 1375 Mm Bed Width: 240 Mm Capacity: Height Of Centre: 165 Mm Swing Over Bed: 320 Mm Swing Over Gap: 510 Mm Swing Over Cross Slide: 180 Mm Distance Between Centres: 650 Mm Slides: Cross Slide Travel: 200 Mm Compound Slide Travel: 115 Mm Spindle: Spindle Bore: 40 Mm Spindle Nose: Thread Type, 62 Mm Spindle Taper: Mt-3 Tail Stock: Quill Diameter: 38.1 Mm Taper: Mt-3 Travel: 120 Mm Speed: No. Of Speeds: Minimum 8 Range: (40 800 )rpm Threading: Metric: (1 6 )mm (min 13 Steps) English: (2 24 )tpi (min 19 Steps) Lead Screw: (1 4) Tpi Electrical: Motor: 1.5 Hp, 230v/415v, 50 Hz Drive: V-belt Structure: Bed: Close-grained Cast Iron (fg 260) Gears: Hardened Steel Base: Rigid Cast Iron Stand , Open Cup Apparatus :specification :standard Compliance: Astm D92 / Is 1448 (part 69) Test Method: Open Cup Flash And Fire Point Determination Test Cup: Brass, Precision Machined With Heat Resistant Handle Heater: Electric Heater (1000 W 10% Nickel Chromium) With Variable Control Heating Rate: 5 6 C Per Minute (as Per Standard) Temperature Range: -6 To 400 C Thermometer: Astm 11c Or Equivalent Flame Applicator: Gas Test Flame With Fine Control Valvebody: Stainless Steel Housing Display: Analog / Digital Temperature Indicator Power Supply: 230v Ac, 50 Hz Safety: Overheat Protection Heat Insulation , Closed Cup Apparatus :specification :standard Compliance: Astm D93 / Is 1448 (part 21) Test Cup:brass Cup Diameter: 50.7 50.8 Mm Capacity: Minimum 70 Ml Stirring System Heater: Electric Heater 650 W 10% Heating Rate: 1 12 C/min Adjustable Ignition: Pilot Flame With Automatic Shutter Mechanism Temperature Measurement: Thermometer Or Digital Sensor(ip-28c Or Astm) Display: Digital Temperature Display Power Supply: 230v Ac, 50 Hz Safety:over-temperature Cut-off Flame Safety Control , Tail Stock Assembly :specification :medium-duty Tailstock Assembly For Dismantling & Assembly Quill Stroke: Minimum 75 Mm Taper: Mt-3 (preferred Standard) Feed: Hand Wheel Operated Features: Set-over Screws For Taper Turning Spindle Locking Arrangement Body: Cast Iron (fg 260) Spindle: Hardened Steel, Slip Gauge :specification :set Size: M87 (87 Pieces) Or Equivalent Range: 1.001 Mm To 100 Mm Step Sizes: 0.001 Mm 0.005 Mm 0.01 Mm Material: High-grade Alloy Steel / Tungsten Carbide (preferred) Hardness: Hrc 63 65 Accuracy: Grade: Grade 1 Or Grade 2 Flatne Flatness / Parallelism: 0.5 M Stored In Protective Wooden Boxes To Prevent Wear; Calibration Grades Include Charts For Exact Sizes , Dc Motor:specification :type: Dc Shunt Motor (dismantling Model) Power: Minimum 0.5 Hp Voltage: 220 V Dc Speed: 1500 Rpm Poles: 4 Pole Construction: Laminated Stator Salient Poles Accessible Armature Features: Cut Section / Open Type Suitable For Dismantling And Reassembly, Hydraulic Cylinder :specification :bore Diameter: 50 Mm Stroke Length: 250 Mm Working Pressure: 160 Bar Cylinder Tube: Honed Steel Piston Rod: Hard Chrome Plated Seals: Standard Industrial Seals End Caps: Steel Calibration Grades Include Charts For Exact Sizes Supply: Mounted On Training Base Suitable For Dismantling And Inspection , Hydraulic Operated Directional Control Valves (dcv):specification :type: Manual Spool Type Dc Valve Configuration: 4/2 Way Size: Ng06 (cetop 3) Rated Pressure: 210 Bar Flow Capacity: 20 40 Lpm Body: Hardened Steel / Cast Steel Spool: Ground And Hardened Ports: Clearly Marked (p, A, B, T) Supply: Mounted On Training Plate Suitable For Dismantling And Study , Bearing With Shaft Assembly :specification :bore Diameter: 50 Mm Stroke Length: 250 Mm Working Pressure: 160 Bar Cylinder Tube: Honed Steel Piston Rod: Hard Chrome Plated Seals: Standard Industrial Seals End Caps: Steelsupply:mounted On Training Base Suitable For Dismantling And Inspection , Coupling Unit Using Driving And Dr
