Description :
Tenders for Supply Of Equipment For Electronics And Communication Engineering Department - Supply Of Equipment For Electronics And Cmmunication Engineering Department, 8051 Micro Controller Kit :specification : Operating Voltage: +5 V Dc. Flash Memory: 4 Kb (at89c51) / 8 Kb (at89s52). Ram: 128 Bytes Internal Ram. 16 2 Alphanumeric Lcd Display. Push Buttons / Tactile Switches. Dip Switches For Digital Input. Inbuilt Adc Interface: Ldr, Potentiometer. Inbuilt Dac Interface. Inbuilt Stepper Motor Driver With Stepper Motor. Inbuilt Dc Motor Driver With Dc Motor. 1 4 Led Array, 1 4 Keypad, 1 Relay. 1 Buzzer, 16 2 Lcd Display, 1 Pwm Driver. 1 Hardware Interrupt Key, Inbuilt Rtc. Inbuilt Eeprom And Uart Module. 4 7-segment Display. Supports Both Assembly And C Language Programming. Pc Interfaceable., Temperaturemeasurementkitspecification : Sensors:rtd (pt-100), Thermocouple (fe-k/j-type), And/orthermistor (ntc). Display: 3 Digit Led/lcd Digital Display(typically 200 Mv Fsd). Temperature Source: Portable Water Kettle Orheater Block. Signal Conditioning: On-board Circuitry Foramplification, Linearization, And Cold Junctioncompensation. Test Points: Multiple 2 Mm / 4 Mm Banana Socketsfor Monitoring Input/output Signals. Power Supply: 230 V Ac, 50 Hz, Single-phase. Accessories: Glass Thermometer, 10 K Ntcthermistor Probe, K-type Thermocouple Probe,patch Cords And User Manual., Ask Modulationanddemodulation Kit:specification : Message Signal1:8-bit Variable Data,amplitude 5v. Message Signal 2:debounced Data, Amplitude Low (0) And High (5 V). Message Signal 3:fixed Data 25 Khz, 12.5 Khz, 6.25 Khz, 3.12 Khz,amplitude 5 V. Carrier Signal: Sine Wave, Frequency 200 Khz,amplitude 5 V. Modulator Type: Switching Modulator Using Analogswitch / Transistor Switching Ic. Demodulator: Envelope Detector And Lpf. Comparator: Lm311 Based. Supply Voltage (board): +12 V, +5 V Dc. Supply Current: 100 Ma Minimum. Input Voltage: 230 V Ac, 50 Hz. Interface Connectors: 2 Mm Banana Socket., Dth Trainer Kit:specification :power Supply: 200 V To 240 V Ac, 50 Hz.dish Antenna: 1.5 Ft Aluminium Steerable Dish Antenna.lnb (low Noise Block Down Converter): Input Frequency: Ku-band. Output Frequency: 950 Mhz To 1450 Mhz. Conversion Gain: 65 Db. Noise Temperature: 35 K (max).set-top Box Receiver In Trainer Form: If Frequency: 70 Mhz. Video Bandwidth: 50 Hz To 5 Mhz. Video Output Level: 1 Vpp At 75 Load. Video Polarity: Normal/inverted, Switch Selectable. Audio Subcarrier Frequency:tunable From 5.0 Mhz To 8.0 Mhz. Remote Control Provided. Hdmi Cable: 10 M.controls: Channel Selection. Volume Control.fault Simulation: Five Built-in Simulated Faults For Troubleshootingexperiments. If Signal Disconnected. Video Output Fault. Audio Mute Fault. Tuner Misalignment. Rf Output Interruption.pcb Size: 15" 12" With Multicolour Section-wise Blockdiagram.standard Accessories: 1.5 Ft Dish Antenna. Lnb. Trainer Pcb. Dish Connecting Wire. Audio-video Cable. User Manual. Acrylic Cover. Hardware Materials For Assembly Of Dish Antenna.additional Features: Dth Subscription Connection Withdoordarshanfree Channels. Free-to-air Channel Demonstration., Fpga Trainer Kit:specification : Must Use Industry-standard Mid-range Fpgadevice Usb-jtag Programmable, Compatible Withvivado Ise (webpack). Power Supply: 5 V Dc Through Usb Or Externaladapter. On-board Peripherals: Leds, Switches, Pushbuttons, 7-segment Display,clock Source, Gpio /pmod Expansion Ports, Uart, Vga / Hdmi, Usbuartbridge, Usb Cable. User Manual.
