Description :
Tenders for Fabrication And Erection -replacement Of The 2" X 2" Square Bar Rails Installed On The Cane Unloader. Removal Of The Old Juice Gutter From 'a' Mill, Fabrication And Installation Of A New One, And Conducting A Successful Trial Run. Removal Of The Old M.s. Juice Tray From 'a' Mill, And Fabrication And Installation Of A New One Using M.s. Plates. Fabrication And Installation Of A New Gear Guard In The 'a' Mill House. Welding Of Worn-out Teeth On The Mill Pinion As Required, Followed By Grinding To A Smooth Finish. Repair Of Damaged/worn Parts Of The Tail Bar Coupling By Welding As Required, Followed By Grinding. Repair Of Damaged/worn Parts Of The Tail Bar By Welding As Required, Followed By Grinding. Comprehensive Repair Of The D.s.m. Screen: Cutting Out And Removing Corroded Sections, Fabricating And Fitting New Replacements, Repairing All Internal Piping, And Conducting A Successful Trial Run. Thorough Cleaning Of The Cane Carrier Slats, Along With Their Attached Links, Pins, Rollers, And Bushes; Followed By Greasing And Refitting Said Components Into The Slats In Their Proper Positions. Thorough Cleaning Of The Slats, Links, Pins, Bushes, And Rollers Of The Primary/secondary Cane Carrier Chains; Followed By Greasing, Assembling The Chain Components, And Preparing The Chain As Per Instructions. Fabrication And Installation Of Juice Rings For The Rollers. Fabrication And Installation Of Mill Bearing Guards Using 3 Mm Plates. Fabrication And Installation Of M.s. Scrapers For The Under-feed Rollers. Cutting Of Chevron Grooves Into Old Mill Rollers As Required. Cutting Of Chevron Grooves Into New Mill Rollers As Required. Creating 'dots' On The Top And Feed Rollers Of The Mill Using Arc-welding Electrodes, As Per Instructions. [repair/replacement Of] M.s. Components For The Worn-out Teeth Of The Under-feed Rollers. Cutting Out Patches From A Plate And Installing Them As New Teeth. Performing Arc Welding On The Grooves Of Rollers Used In The Mills Using Electrodes, As Per Instructions. Fabricating Side Juice Guards For Mill Rollers From 3 Mm Plates, As Per Instructions. Fabricating An Under-feed Roller For The Mill In Accordance With The Provided Drawings. Dismantling A Damaged Or Defective Juice Tank In The Mill House; Fabricating And Installing A New Tank In Its Place, And Conducting A Trial Run. Replacing Or Repairing The Damaged Sections Of A Defective Juice Tank In The Mill House. Dismantling And Replacing The Bottom Plate Of A Damaged Or Defective Juice Tank In The Mill House. Cane Carrier / Bagasse Carrier / Bagasse Elevator / Cross Bagasse Carrier / R.b. C. Removal Of The Cane Carrier Side Plate And Installation Of A New Plate. A. Welding Or Forging The Enlarged Pin Holes In The Links Of The Cane Carrier, Bagasse Carrier, Etc., To Match The Specific Pin Size. A. Removal Of Broken Runners From The Cane Carrier, Inter-carrier, Bagasse Elevator, Return Bagasse Carrier, Or Cross Bagasse Carrier, And Installation Of New Runners In Their Place. A. Removal Of Old, Damaged Cane Carrier Slats And Installation Of New Slats. A. The Task Of Drilling Holes In New Slats For The Cane Carrier And Inter-carrier. A. Straightening And Repairing Cane Carrier Slats As Required. A. Repairing Damaged And Weakened Hoods Of The Cane Chopper, Cutter, And Fibrizer In Accordance With Instructions. A. Removal Of Old, Damaged Cane Carrier Slats; Straightening The Damaged Slats; Cutting Out The Damaged Sections; And Repairing Them By Welding In New Or Salvaged Slat Pieces Cut To Size, Thereby Restoring The Slats To Their Proper Dimensions. A. Welding The Enlarged Holes In The Inter-carrier Links And Re-drilling Them To The Correct Size To Match The Rivets. A. Filling The Enlarged Holes In Old Inter-carrier Slats By Welding, And Subsequently Re-drilling Them To Create New Holes In Accordance With The Engineering Drawings. A. Removal Of The Damaged Band From The Inter-carrier Clutch Shaft, Fabricating And Installing A New One, And Conducting A Satisfactory
