Tender For corrigendum : ridf xxviii - lift irrigation projects in various padashekharams of wayanad district- procurement of submersible pumpsets, fittings, accessories, and related electrical works - procurement, installation, erection, testing, and commissioning of pumpsets and allied works at punchavayal, manikkuni, kolembetta, valiyavattam, and padiyeri pumphouses. - procurement, installation, erection, testing, and commissioning of pumpsets and allied works at punchavayal, manikkuni, kolembetta, valiyavattam, and padiyeri pumphouses., supply, installation, erection, testing, commissioning and fitting charges for all accessories of horizontally mounted submerged centrifugal non clog pump set of compact unitary mono-block submerged single/multi stage,volute type casing with suitable radial type impellers on common shaft for pump and motor ,anti friction bearing with life time greasing, protection features with sensors to monitor temperature,mechanical seal leakage ,etc.(the pump should be confirming to his/is standards).the moc of pump,casing-cast iron,impeller -ss cf8m,shaft-ss-316,suction strainer -ss and other as per is standard.the motor should be suitable for 3 phase,415v /-10%,50hz /5%,ac supply submersible motor having class f /h insulation, air filled and ip-68protection confirming to is 325 or latest standards suitable for day night operation.the pump discharge capacity of 230 cubic metre /hour against duty point head of 42 mtrs, working head range 18 - 47m, discharge range 136 - 57 lps ,speed 1450rpm(n) or nearer ,with 10meters of copper power cable and control cable, railing arrangement. the pump should be painted with three coats of suitable anti corrosive paint over priming coat. the electrical works for the pumpset should be completed as per kseb rules and regulations and the contractor is responsible for arranging premissions and certificates from the electrical inspectorate. the suction side of the pumpset should be provided with an additional iron grill for preventing foreign particles inside the inlet side of the pump casing., supply and erection of 60hp auto transformer starter (ats) with suitable incommer and contactors including 24 kvar capacitor with required indications ,metering and protections for single phasing ,overload, pump monitoring unit to protect from ingress, high temperature level etc enclosed in a closed panel board, supply and laying additional termination cable of 1.1kv 3.5 core 95sqmm aluminium conductor xlpe insulated ;steel armoured ug cable as per relevant is 7098 with support for cable, supply, installation, erection, testing, commissioning and fitting charges for all accessories of horizontzlly mounted submerged centrifugal non clog pump set of compact unitary mono-block submerged single/multi stage,volute type casing with suitable radial type impellers on common shaft for pump and motor ,anti friction bearing with life time greasing, protection features with sensors to monitor temperature,mechanical seal leakage ,etc.(the pump should be confirming to his/is standards).the moc of pump,casing-cast iron,impeller -ss cf8m,shaft-ss-316,suction strainer -ss and other as per is standard.the motor should be suitable for 3 phase,415v /-10%,50hz /5%,ac supply submersible motor having class f /h insulation, air filled and ip-68protection confirming to is 325 or latest standards suitable for day nightoperation.the pump discharge capacity of 188 cubic metre /hour against duty point head of 35 mtrs,working head range 16 - 42m, discharge range 102 - 42 lps ,speed 1450 rpm(n) or nearer ,with 10meters of copper power cable and control cable,railing arrangement. the pump should be painted with three coats of suitable anti corrosive paint over priming coat. the electrical works for the pumpset should be completed as per kseb rules and regulations and the contractor is responsible for arranging premissions and certificates from the electrical inspectorate. the suction side of the pumpset should be provided wi
Tender For corrigendum : procurement of e and h make spares for c and i at ntpc mouda - main board kit,50104751,endress+hauser, xmtr,lvl: sonic,4-20ma,fmu44-atb2a42a, ult lvl tx unit,fmu90r11cb111aa3a,e+h, us sensor,fdu91-rg3aa,e+h, xmtr,lvl: radar,50m,24vdc,fmr60baabaeah+, display unit,52026443,endress+hauser, electronics,71344231,endress+hauser, kit meas. amplifier,71029345,e&h, connection card,50094016,e+h, power supply card,71323009,e+h, display module,xpd0031-aa0f00,e&h, i/o module,slot1,xpd0037-aaa100,e&h, i/o module,xpd0038-aa1a00,e&h, isem promass 300,xpd0028-aa0iaaa00+,e&h, switch,pres,(-1)-(+40)bar,ptp31b74n7,e&h, swch,prs: 0-100kg/cm2,24vdc,dpdt, switch,pres,0.5-10bar,ptc31b,e&h, switch,temp,rtd,(-50)-(+200)deg.c,e+h
Tender For procurement of spares for cst drive of conveyor - pump seal, part no.- 61160680 , filter element 10 mcrn, part no.- 61163139y , filter element 25 mcrn, part no.- 61163139v , breather element, gearcase, part no.- 61161010a , screen y strainer, part no.- 61166616a , gasket for 1.25 inch y- strainer, part no.- 61166616b , busket 40 mesh, 3 inch port, part no.- 61166613b , inline relief valve, part no.- 61164004ar , pressure gauge btm mounting, part no.- 70785401ae , pressure gauge, part no.- 70785401aj , relief valve assembly, part no.- 61164032 , cplg, half, part no.- 61313065a , cplg, half, part no.- 61313065b , ring, snap, dia 3 mm, part no.- 61313065c , pin, wrbr, stl20, part no.- 61313065d , filter assembly 10 micron, part no.- 61163139x , sub assembly 25 micron filter, part no.- 61163145b , viking pump coupling, part no.- 61313032b , subassy, hydra lic manifold, part no.- 61408410ad , hose y strainer to viking pump, part no.- 41977243a , hose viking pump to sys filter, part no.- 41977241b , hose manifold to clutch, part no.- 41977241c , hose relief valve to viking pump, part no.- 41977241d , hose assembly, heat exc skid, part no.- 61319794a , hose assembly heat exc skid, part no.- 61319794b , ass flex hose, part no.- 70861337 , oil temperature rtd transmitter, part no.- 42006203 , pwm amplifier, part no.- 61400204na , pressure control valve, part no.- 61400207b , coil 24v dc, part no.- 61400207c , three wire speed sensor, part no.- 61164444 , pressure transducer, part no.- 42004620f , flowmeter, part no.- 42004629k , flow meter, part no.- 42004629h , power supply, 24vdc, part no.- 61310617g , panel view plus, part no.- 61315420a , cpu module compact logix, part no.- 70783545aa , power supply plc, part no.- 70783545ca , analog input mod, part no.- 70783545ga , mdl, analog combination, part no.- 70783545gb , counter high speed, 4ch mod, part no.- 70783545ha , discrete input fast speed mod, part no.- 70783545db , discrete output isolated acdc mod, part no.- 70783545ea
Tender For supply of iot trainer or development kit,trainer kit for raspberry pi,arduino starter kit,arduino mega 2569 controller with cable,node mcu or esp32 dev wroomer controller 40 pin,esp32 cam development board wifi with bluetooth with ov2640 camera module,j1020 edge al device with jetson nano module, aluminium case, pre-installed jetpack system,beagal board al controller,double channel relay module,5v, 8 channel relay module,static relay module, 4-channel,servo motor,ir sensor,sharp ir,hall-effect rotary encoder,encoder sensor module,microwave doppler radar motion detector sensor,gas sensor lpg,accelerometer sensor,soil moisture sensor,npk sensor,buzzer module 5 v,rgb led module,ultrasonic sensor,serial rtc,dth11 sensor,rfid card reader module with 2 tags,hd night vision web ip camera with serial out,vr camera,laser detector sensor module,laser pointer,pir motion sensor module,power sensor,pulse sensor, heart rate detector,humidity and pressure sensor,analog ph sensor kit with circuit and probe,turbidity sensor with module