Tender For corrigendum : procurement of e and h make spares for c and i at ntpc mouda - main board kit,50104751,endress+hauser, xmtr,lvl: sonic,4-20ma,fmu44-atb2a42a, ult lvl tx unit,fmu90r11cb111aa3a,e+h, us sensor,fdu91-rg3aa,e+h, xmtr,lvl: radar,50m,24vdc,fmr60baabaeah+, display unit,52026443,endress+hauser, electronics,71344231,endress+hauser, kit meas. amplifier,71029345,e&h, connection card,50094016,e+h, power supply card,71323009,e+h, display module,xpd0031-aa0f00,e&h, i/o module,slot1,xpd0037-aaa100,e&h, i/o module,xpd0038-aa1a00,e&h, isem promass 300,xpd0028-aa0iaaa00+,e&h, switch,pres,(-1)-(+40)bar,ptp31b74n7,e&h, swch,prs: 0-100kg/cm2,24vdc,dpdt, switch,pres,0.5-10bar,ptc31b,e&h, switch,temp,rtd,(-50)-(+200)deg.c,e+h
Tender For procurement of spares for cst drive of conveyor - pump seal, part no.- 61160680 , filter element 10 mcrn, part no.- 61163139y , filter element 25 mcrn, part no.- 61163139v , breather element, gearcase, part no.- 61161010a , screen y strainer, part no.- 61166616a , gasket for 1.25 inch y- strainer, part no.- 61166616b , busket 40 mesh, 3 inch port, part no.- 61166613b , inline relief valve, part no.- 61164004ar , pressure gauge btm mounting, part no.- 70785401ae , pressure gauge, part no.- 70785401aj , relief valve assembly, part no.- 61164032 , cplg, half, part no.- 61313065a , cplg, half, part no.- 61313065b , ring, snap, dia 3 mm, part no.- 61313065c , pin, wrbr, stl20, part no.- 61313065d , filter assembly 10 micron, part no.- 61163139x , sub assembly 25 micron filter, part no.- 61163145b , viking pump coupling, part no.- 61313032b , subassy, hydra lic manifold, part no.- 61408410ad , hose y strainer to viking pump, part no.- 41977243a , hose viking pump to sys filter, part no.- 41977241b , hose manifold to clutch, part no.- 41977241c , hose relief valve to viking pump, part no.- 41977241d , hose assembly, heat exc skid, part no.- 61319794a , hose assembly heat exc skid, part no.- 61319794b , ass flex hose, part no.- 70861337 , oil temperature rtd transmitter, part no.- 42006203 , pwm amplifier, part no.- 61400204na , pressure control valve, part no.- 61400207b , coil 24v dc, part no.- 61400207c , three wire speed sensor, part no.- 61164444 , pressure transducer, part no.- 42004620f , flowmeter, part no.- 42004629k , flow meter, part no.- 42004629h , power supply, 24vdc, part no.- 61310617g , panel view plus, part no.- 61315420a , cpu module compact logix, part no.- 70783545aa , power supply plc, part no.- 70783545ca , analog input mod, part no.- 70783545ga , mdl, analog combination, part no.- 70783545gb , counter high speed, 4ch mod, part no.- 70783545ha , discrete input fast speed mod, part no.- 70783545db , discrete output isolated acdc mod, part no.- 70783545ea
Tender For supply of motorola make spares ugmcs system c c -programming port dust cover for xirp8668i , volume knobe for xir m8668i , 10 foot, 20 amp cables to power battery for xir m8668i , fist microphone for motorola base station xir m8668 , programming cable for walkie talkie xir p8668i , programming cable for base station xir m 8668i , programming cable for repeater slr 5300
Tender For a)retrofit/up gradation of existing schneider make plc and scada/hmi systems installed at rtps-unit 8 dpmrhs.b)the bidder/agency shall be required to supply the materials as per the technical specifications and quantity mentioned under the head of technical specifications.c)the bidder/agency shall be required to install and commission the supplied materials in the existing plc control cubicle itself by retaining existing ipr(interposing relays),mcbs and tbs.d)the bidder/agency shall be required study the existing software/logics incorporated in the plc/scada system, further to carryout re-engineering works, software/logics development based on customer/site requirement and also for the assessment of additional accessories required to complete the retrofit/upgradation works in complete manner.e)it is the single point responsibility of the bidder/agency to carry out the works in the stipulated time period.f)providing required power supply will be under the scope of kpcl itself.g)t&p and any other consumable materials required for the work will be under the scope of agency/contractor only.h)before quoting the bid, it is compulsion to visit the site for the assessment and studying the site/customer requirement.i)storage of materials while executing works is single point responsibility of contractor/agency scope itself.j)the agency shall be required to handover as built drawings and software backup cds (os,application and system software) along with o&m manuals 04 sets.k)materials supply shall be completed in all respect within the stipulated period as per the contract. materials shall be delivered to rtps site through ee(stores)o&m. unloading of materials at rtps site location and shifting of the same to work location is under the contractor/agency scope only.l)handling, shifting, unpacking and erection and commissioning of the entire system shall be under the scope of bidder itself.m)all required consumables, hardware and licenced software, accessories and any other materials which are not included in the scope and required for successful installation and commissioning of the retrofit/up gradation of existing dpmrhs plc system of rtps unit-8 to latest version will be under the contractor/agency itself.n)all the materials required for the installation and commissioning of up gradation of existing dpmrhs plc system of rtps unit-8 to latest version shall be made as detailed under the technical specifications and shall be installed and commissioned as per the scope of work.o)warranty-all the materials and other equipment covered under supply portion shall cover a warranty for a period of 12 months from the date of commissioning or 18 months from the date of supply.warranty-all the materials and other equipment covered under supply portion shall cover a warranty for a period of 12 months from the date of commissioning or 18 months from the date of supply. any faulty items/spares observed during this period shall be replaced at free of cost.