Tender For tender for supply of disk connecting membrane , valve shut-off straightway flange brass py 25 dy 32 , valve shut-off straightway flange bronze py 10 dy 50 , valve disk for 521-01-186 tm shut-off dy 100 , disk , valve disk , valve disk , disk , valve gate flange bronze py 6 dy 125 , joint nipple and edge union steel dy 20 , joint nipple and union bronze py 100 dy 20 , joint nipple and union bronze py 100 dy 32 , union intermediate bronze dy 6 , union branch steel dy 20 , union branch body dia 3mm py 40 , addl. union edge joint butt dy 18/6 py 200 , addl. union edge joint butt dy 10 py 200 , addl. union edge joint butt dy 32 py 200 , union edge adapter joint butt dy 20/10 py 200 , intermediate union butt dy 32 py 200 , intermediate union butt dy 6 py 200 , addl. union adapter edge butt dy 10/6 py 200 , valve , sealing diaphragm between electromagnet cavity and governor , flange dia 40 , protector , durite coupling , pusher/tapet hydraulic , dirt remover part 69 , plate stop , turbo compressor motor locking plate , contact fixed , contact movable , air distributor dia 150 , conical pipe adaptor dy 20/9 py 400 , screw coupling dy 9 py 400 , band for durite coupling dia 81-90 , durite coupling dia 120-210 , protector 15-1 , protector , membrane , nozzle prewetting bronze , contact k e-45 , bag cover for water seperator ct-500-2 ko4 , button strip 15x5x32t , shim non magnetic , shim non magnetic , packing gland , extender , clamp/yoke/clip , sealing , sealing seal , spring , power take off shaft sealing cup spring , spring locking for doors , spring , spring , spring , spring , spring , spring , spring , spring c sh p-3-iii-2x17x42x7 , spring c sh p-3-ii-4x38x163.3x12 , spring , spring c sh p-2-ii-2.5x24x60x6.5 , spring , spring 1-15-0
Tender For tender for supply of canopy 8x8 , fuel filter fj 4a4 , clutch booster repair kit , repair kit for air pressure governor , coil assy ignition , mounting engine front , switch assy change over , cable assy speedometer , top deck assy grey , sensor water temperature , seal front oil 32x47x6 , head lamp assy , horn assy high , mirror assy inner rear view , gasket cyl head cover , belt water pump
Tender For corrigendum : tender for supply of 25bz2c005 spares of convertor diesel alternature emergency diesel generator and emergency genset d d -diodes for rev diodes disc , automatic voltage regulator , discrete protection relay unit , indicating lamp bulbs set of 4 nos , diodes for rev diode disc , air cleaner , piston ring set , ball sheel with bush , packing for fuel filter , gear wheel for de comp auto , sliding disc , governor lever , rocker assy inlet , gasket for fuel pump , shims for fuel pump o 30mm , disc for ball hub , cylinder head nut , packing for bearing flange gasket , cover for crank shaft , cylinder head gasket 0 05 mm , cylinder head gasket , cylinder head gasket 0 80 mm , fly wheel nut , valve cup collet , piston std , automatic voltage regulator solid state electronic , manual voltage adjuster potentiometer set of 1 no , lamp bulbs indicating set of 6 nos , dip stick , roller bearing nu 307 , diodes for rev diode disc set of 7 nos , diodes for rev diode disc set of 7 , revolving diode set disc complete with diodes , fuel tank cap , oil seal flywheel end , air filter inlet cap , banjo bolt 8mm , key for fly wheel , cotter pin 2x22 din 94 for hand lever , gudgeon pin , o ring 5x7x1 for pin of de comp , o ring for oil filter cap , o ring for bottom cover lever , injector assembly , v ring , o ring for decompressor , fuel pipe 26 tank to filter , key for hand lever , banjo bolt 12mm , protection cap , valve guide , cam flower spindle
Tender For the detail of works includes:a. the tenderer shall carryout the following works during annual maintenance contract period along with the servicing of the diesel generator set.1. general checkup & preventive maintenance and to fill up preventive checkup schedule as follows:a) check lube oil level and conditioning of lube oil, top up/refill if required.b) the oil filters shall be replaced whenever oil is changed.c) the air filters shall be cleaned periodically with compressed air, check batteries and top up the distilled water if required.d) check functioning of changing alternator.e) engine safety viz. high water temperature gauge, oil temperature gauge and high speed gauge shall be checked for their functions and repaired/replaced if required.f) coolant level and conditioning of coolant shall be checked and refilled if required.g) check fan and alternator drive belts and tightened if required.h) the governor shall be checked and tuned for proper functioning.i) check for leaks if any and shall be rectified.j) check reports shall be submitted every month/every breakdown calls.2. checking and servicing of engine for smooth running, its unusual sound and color of smoke and exhaust and set it right in case of deviations.3. checking and repairing and leakage of fuel, lubricating oil and coolant.4. cleaning and changing of air filters as per requirement.5. setting of valves tappets whenever required.6. checking and repairing of accessories drive, turbo charger and crankshaft endplay whenever required.7. checking of alignment of engine & alternator as per requirement.8. checking of throttle control and its setting.9. checking of instrument panel including replacement as and when required.10. checking of rotating diodes assembly in brushless alternator including replacement as and when required.11. checking of wiring system and repairing/replacement as and when required.12. repair and maintenance of relays including contractors in control panel.13. checking of battery terminal and de-sulphating.14. diagnosis of faults in engine and alternator and its rectification.15. breakdown calls to be attended on priority within 6 hrs.16. providing spare avrs, self-starter and accessories, free of charge, if the repair/overhaul/replacement is expected to be taken in more than two days.17. checking/repair/adjustment/replacement/servicing shall be carried under annual maintenance contract except cost of component/parts to be replaced due to wear & tear.18. the firm should undertake to arrange genuine spares of the diesel engine, alternator and amf panel as and when required within two working days.19. the tenderer’s service engineer shall visit the site for attending the generator sets not less than twelve times during the contract period (minimum once in a month) and shall inspect the generator set thoroughly. each visit shall take place during 1st week of each month.20. the tenderer’s service engineer shall visit once in two month for checking of electrical side viz. alternator, amf control panel, if any.21. the engine shall be run on no load or at available load, and should be checked for any leakage and abnormal noise. if any such abnormality noticed shall be diagnosed and remedial action shall be taken.22. standard check list:a) replace minor parts (i.e hoses and filters etc) sub-assemblies as and when required.b) service engineers during the visit will report on the performance or any other abnormality and inform parts requirement. he shall also submit the report on work done and recommendations as well as spare parts required.c) attend emergency call on priority (usually same day). however, if the engineer is required or any particular date and time, it would be the responsibility of the customer to intimate the contractor in advance.d) major overhauling/ top overhauling / pt pump & injector calibration /replacement of major parts/ rewinding of alternator or repairs or breakdown of the diesel generator set are to be charge
Tender For supply of pressure governor p2 for knorr bremse make air brake panel of wag-7 locos kb part no.-i84649/04643. specn: kb part no.-i84649/04643 [ warranty period: 30 months after the date of delivery ]
Tender For corrigendum : supply of pressure governor p2 for knorr bremse make air brake panel of wag-7 locos kb part no.-i84649/04643. specn: kb part no.-i84649/04643 [ warranty period: 30 months after the date of delivery ]