Tender For supply of vita ambria ingots shade a1 , vita ambria ingots shade a2 , vita ambria ingots shade a3 , vita ambria ingots shade a3 point 5 , vita ambria ingots shade b1 , vita ambria ingots shade b2 , vita lumex 50g veneering material shade b2 , vita lumex power wash shade a3 point 5 , vita lumex power wash shade b1 , investment material for pressable ceramic system powder 25 pkt with liquid 1 ltr , vita akznet plus glaze powder 5gm , vita glaze liquid 20ml , vita opaque powder shade a2 , vita opaque powder shade a3 point 5 , flexible denture material cartridge box of 15 cartridges , blue inlay wax , die lubricant bott of 70ml , nicr alloy for casting , sintered diamond bur flame shaped , sintered diamond bur bullet shaped , porcelain instruments kit , denture polishing cake , denture polishing buff medium size 4 inch , calcium hydroxide powder for dental use bott of 15 gm , hyrax screw , niti open coil spring with eyelet pkt of 10 each 9mm 12 mm and 15 mm sizes , blue bite block light cure radiopaque composite , ortho bondable lingual buttons pkt of 10 , class ii malocclusion corrector , orthodontic modules transparent with some colorful modules , orthodontic ligature wire , orthodontic elastic chain continuous02 and long 02 , arch wire stainless steel size 0point16x22 for upper , arch wire stainless steel size 0point16x22 for lower , arch wire niti size 0point16x22 for upper , arch wire niti size 0point16x22 for lower , arch wire niti size 0point16 for upper , arch wire niti size 0point16 for lower , arch wire niti size 0point14 for upper , arch wire niti size 0point14 for lower , maarpe miniscrew assisted rapid palatal expansion , tads temporary anchorage devices , crimp able hooks for arch wires , elastic thread , self ligating brackets , jack screw , interproximal stripping strips double sided pack of 12 pcs , composite interproximal polishing strips box of 100pcs , thermoplastic impression trays set of 12 , glass fibre post 3d size0 box of 10 pcs , advanced sectional matrix system kit with 2 refill packs each , ridge split kit , narrow ridge expansion kit , metal casting ring size 3 , self adhesive resin cement , denture metal flask for acrylisation no 9 , hinge articulator , clamp for double flask , finishing and polishing kit for zirconia and lithium disilicate , light cured composite opaque , enamel composite kit for extended aesthetics , gingiva composite kit for extended aesthetics , sheets for vaccum pressure moulding system set of 10 sheets , pattern resin 1 to 1 package , partial extraction therapy bur set kit socket shield therapy kit set of 10 burs , direct aesthetic composite kit with patented sprg technology , self cured universal adhesive , root canal irrigation needle 30g , bio c repair putty , edta liquid , optrastick refill 48 , dual force anatomic active wedge set of 5 , mta angelus , cotton roll for dental use pack of 1000 pcs , soldering flux dental , soldering wire dental , gingival retraction cord bott of 100 inches //bid details 2 / 58
Tender For painting of high performance thermo plastic co-polymeric anticorrosivecoating system (system-iii) for long painting free life (15 years & above) as per rdso specification m&c/pcn/121/2011, at br. no. rub 245 (1x15.26m) smql line, shunting line & platform girders at dsa station on dsa-smql-sre section in the jurisdiction of xen/bl/tkj.
Tender For supply of 2003655 , 2003690 , 2003708 , 2003717 , 2003733 , 2003734 , 2003735 , 2003736 , 2003737 , 2003738 , 2003739 , 2003740 , 2112483 , 2112484 , 2114138 , 2114139 , 2114146 , 2114152 , 2114162 roll2003655 material : alloy cast steel hardness : 40-45 shore c drawing reference : 1-d22939, rev-c tensile strength : 85 to 100 kgf/mm stand no : billet mill 1 & 2 size : 850 x 1200 mm barrel hardness : 40-45 shc roll approximate unit weight : 7.35 tons uts : 85-100 kgf/sq.mm neck hardness :40-45 shc neck runout :0.04 mm roll coating : anti-corrosive ring hardness :600-700 hv3 test certificate required : yes ring drawing no : mec/1/22938/rev c ----------------------------------- special instructions: ----------------- ------------------ 1) ultrasonic,uts & %elongation tests shall be done and certified. 2) flat wobblers to be strictly concentric with roll neck journals. 3) rolls to be suitably packed and numbered for identity. 4) the microstructure should be free from continuous network of carbides along the grain boundaries. 5) t.c. to be given along with micro-structure photograph. a seperate copy to be sent to d.g.m(rs&rs) at the time of delivery. 6) the rolls shall be guaranteed against manufacturing defects such as blow holes, cavity, non-metallic inclusions, pipe segregation, cracks, hard spots, flakes etc which may adversely affect their service life. 7) should any roll fail prematurely or give sub-standard performance due to the above defects, the suppliers shall rectify the defects at their cost wherever possible to the entire satisfaction of vsp or make prorata compensation or make full replacement if the roll has been ) /bid number : gem/2026/b/7416074 * /dated: 16-04-2026 & & / bid document 1 / 40 rejected before use. 8) the rolls are also to be guaranteed for the roll life as mentioned or 5 years from the date of supply to vsp which ever is earlier.this guarantee clause superseeds, guarantee mentioned elsewhere in the po(a/t), in this regard. 9) hardness test of end ring shall be done and certified. 10) these rolls are used in roughing stands of hot rolling mill. roll set life: bh1=14.35, bh2=14.55 lakh tons, roll2003690 material : sg cast iron (accicular) hardness : 70-75 shore c drawing reference : 1/4012885, rev-e stand no : bar mill 19 & 21 size : 360 x 600 mm barrel hardness : 70- 75 shc roll approximate unit weight : 0.70 tons neck hardness :38-45 shc neck run out : 0.04 mm roll coating : anti-corrosivecoating drop in hardness : 1 shc per 10mm on barrel depth ---------------------------------- -------------- special instructions: -------------------------------------- ---------- 1) flat wobblers to be strictly concentric with roll neck journals. 2) rolls to be suitably packed and numbered for identity. 3) t.c. to be given along with micro-structure photograph. a seperate copy to be sent to d.g.m(rs&rs) at the time of delivery. 4) the rolls shall be guaranteed against manufacturing defects such as blow holes, cavity, non-metallic inclusions, pipe segregation, cracks, hard spots, flakes etc which may adversely affect their service life. 5) should any roll fail prematurely or give sub-standard performance due to the above defects, the suppliers shall rectify the defects at their cost wherever possible to the entire satisfaction of vsp or make prorata compensation or make full replacement if the roll has been rejected before use. 6) the rolls are also to be guaranteed for the roll life as mentioned or 5 years from the date of supply to vsp which ever is earlier.this guarantee clause superseeds, guarantee mentioned elsewhere in the a/t, in this regard. 7) these rolls are used in hot rolling mill. roll set life1: 19re16&18=2.00,19re20=1.62 l.tons roll set life2: 21re25=2.34, 21re36=0.7 lakh tons roll set life3: 21re28&re32=0.90, 21re32, re36=0.70 lakh tons roll set life4: 21rore16,18=2.16, 21re20=2.13 lakh tons, roll2003708 material : sg cast iron (accicular) hardness : 70-75 shore
Tender For supply of modified 10" pitch (254mm)chain for flight roller conveyor to wap drawingno.702064610880 with 14 sub drawings" as furnished in the above drawing. special conditions: 1 tenderer should be in the line of manufacturing industrial chain and shall have in house facilities to manufactur and test the manufactured chain however heat treat ment process can be out sourced. 2.raw material for chain manufacturing shall be procured through reputed sources m/s sail, tisco, isp&t, ismt, jindal, msl, kalyani or tata and the documents for having procured the raw material from the above sources to be furnished at the time of inspection. 3.material test certificate for all the components of the chain shall be furnished at the time of inspection. 4.the tenderer shall produce documentary evidence for having manufactured and successfuly supplied industrial conveyor chains to rwf or any other organiztion in the last 10 years. 5.the chain shall be coated with anti-corrosivecoating after assembly of chain before packing. 6.the chain shall be covered with thick polythene sheet and packed in wooden pallets. ]