Latest anti corrosive painting Tenders | Government anti corrosive painting Tenders

CTN :45140253

20 May, 2026 NA

Sonitpur - Assam

Tender For supply of terminal snow white , led bulk head fitting with led lamp 10 watts , pvc flexible wire copper conductor multi stranded 0 point 0016 oblique 76 , pvc flexible conduit pipe 15 mm dia , pvc round oblique square block , fire extinguisher of one kilogram capacity dry power type along with its accessories , change over switch 32 amp 4 pole , earthing plate 600 x 600 x 6 mm galvanised steel suitable for gi strip fittings , ci earth pit cover of size 300 x 300 x 6 mm with angle iron of size 20x20mm , funnel fitted with 20 mm diameter gi pipe 1 point 5 m long pipe , gi wire 4 mm diameter for earthing , charcoal , salt normal , air termination single pointed aluminium rod 12 mm dia and 300 mm long , testing point terminal block make of gun metal and phosphorus bronze size 75 x 75 x 25 mm drilled , aluminium strips 25 x 3 point 0 mm , galvanized iron strip 32 x 6 mm , insulating pvc block 75x75x30 mm with insulating clamp nut and bolt , individual standalone plastic body smoke alarm with adequate provision for fixing on wall oblique ceiling oblique roof , individual standalone plastic body heat alarm with adequate provision for fixing on wall oblique ceiling oblique roof , fire ball extinguisher of 2 kg wt with suitable provision for wall mounting , double sleeping bunk alongwith rexene sleeved mattress , steel bed side locker of size 1000mmx1520mmx450mm , study chair of size length 56 cm comma height 82 cm and width 56 cm , study table of size 4 x 2 wooden top round tube structure with three drawers , looking mirror of selected quality frameless of size 600x450x5mm , water dispenser of 230 v 500 watts without refrigerator with normal cold and heating capacity of 5 ltrs , portable indoor type high quality kero heater metal body with capacity 4 ltr , plastic dustbin of capacity 40 ltr , supply comma installation comma testing and commissioning of 5 kva cpcb iv plus compliant genset , supply comma installation comma testing and commissioning of amf panel to controling auto operating of 5 kva genr set , coarse sand free from vegetation , coarse aggregate 20mm graded , coarse aggregate 40mm graded , hard core 40 to 63 mm graded , stone for rr masonary less than 6 inch , pre painted galvatume aluminium zinc coating gi based corrugated steel sheet 0 point 50 mm thick , ms pipe med grade 50mm dia , painting brush 4 inch , anti corrosive red oxide zinc chromate primer , synthetic paint enamelled og confirming , thinner , self driving scrw for ppgi sheet 100 nos per pkt , iron welding rod 3 point 15mm thick 100 nos per pkt , pvc tape 19mm wide 5m long , on load change over switch within sheet steel enclosure 32 amps 4 pole tpn , cable pvc insulated electric cables heavy duty 1100 volts grade multi stranded copper conductor of size 1 point 5 sqmm single core , cable pvc insulated electric cables heavy duty 1100 volts grade multi stranded copper conductor of size 2 point 5 sqmm single core , cable xlpe insualted screened pvc bedded comma galvanised steel strip or wire armored electric power cable heavy duty 1100 volts , switch piano 5 amp 230 volts flush type one way , switch socket combination multipurpose 2 in 1 comma 15a comma 230v , led tuble light fittings 15w 230v box type 4 feets with crca body , screw full thread 6x19 mm , pvc switch board of size 7 inch x 4 inch for socket and switches , ceiling rose three terminal , pvc round oblique squire block , distribution box 4 way double door spn 240 volts copper bus bar and neutral link earthing stud , service cable pvc insulated aluminium conductor 1100 volt grade heavy duty , earthing plate 600x600x6mm galvanised steel suitable for gi strip fittings drilled with two nos holes for 6 //bid details 2 / 70 mm dia near one side , ci earthing pit cover of size 300x300x6mm with angle iron isa 20x20x3mm thick ms frame , funnel fitted with 20mm dia gi pipe 1 point 5m long , salt normal , fuel filter element primary , fuel filter element secondary , fuel flexible pipe , hose pipe , engle oil , o

CTN :45139981

29 May, 2026 NA

Jammu - Jammu And Kashmir

Tender For supply of ldpe film , srt 6 ft , srt 10 ft or 16 ft , ismb 20 ft , bricks , laip , cement bag , acrylic sheet , acrylic sheet 6 ft x 4 ft x 4mm , agg 20 mm , almera , alu door , alu window , antigrating 4 , bib cock water tap , gi binding wire , brass bib tcock , btc door , bulk head fitting , casing capping , ceiling panal 2 ft x 2 ft , ceiling rose , cement base primer , cgi sheet 10 ft , cgi sheet 12 ft , cgi sheet 8 ft , conical shed , cp cloth hanger 6 peg , curtain rod 1.5 mtr , curtain rod with stand , distemper , door closer , false ceiling , fire extinguisher 2 kg , flush tank 10 ltr , floor tile 2 x 2 , folding ladder , gabion basket , gi pipe 1.3inch 20ft long , glass putti , hdpe sand bag , i star srew , iwc sheet , jerrican 35 ltr , jet spray gun for toilet , l 12ft long , locker , mirror 4 x 2 , main door , mixer cock , mixter tap , ms steel door , nails 1.5 inch , office table , og paint , oil bond distemper , paint black , paint brown , painting brush 2inch , painting brush 3inch , painting brush 4inch , white paint , paint red oxide , pbs roll size of 20 mrt x 0.90mtr , plywood 8ft x4ft , profile sheet 10ft , puf pannel door , purline 3 ft x 2 ft 90ft long , pvc bib tab 15mm , pvc connection pipe 2inch , pvc connector , shop dish , single bunk bed , water tank 1000 ltr , water tank 200 ltr , square box , srt 8 ft , steel hex head self drilling screw 1inch long , steel hex head self drilling screw 2inch long , steel hex head self drilling screw 3inch long , stop cock , water tank 500 ltr , t 1.3inch , t 12 inch long , t 2 inch long , t 4 inch long , tape insulation , taping screw 2inch , tarepene oil , tile cutter , tiles 1ft x1 ft , towel hanger , union , wastage pipe , water proof plastic 15 ft x15 ft , welding rod , window glass ) /bid number : gem/2026/b/7515779 * /dated: 08-05-2026 & & / bid document 1 / 74

CTN :45137750

19 May, 2026 NA

Kamrup - Assam

Tender For supply of ms plate of size 12mm thick , ms frame work for roof trusses purlin rafter and ms plate etc all as directed make tata or sail or jsw ms angle of size 40x40x6 for cleat , ms nuts and bolts of length 100mm fully thread suitable for 10 mm dia nuts including two numbers of washers and 25mm of shank and two nos of washers 3 mm thick complete all as directed. , ms flat iron 40x5mm thick for wind tie make tata or sail or jsw , iron welding rod confirming to is 814 to 2002 isi marked 3.15 mm thick 100 nos pkt , water proofing compound confirming to is 2645 to 2003 make pidilite or dr fixit or fevicol , quick setting compound make pidilite or fevicol or quick fix , cement based paint snowcem make berger or asian or nerolac , oil bound distemper washable quality of proprietary brand of make nerolac or berger or asian , birla white wall care putty water resistant white cement make nerolac or berger or asian , ppgi roofing sheet 10 feet x 3 feet long and thickness 0.63 mm with grard film. as per technical specification and drawing attached , pre painted galvatume aluminium zinc coating gi based plain steel sheet 0.50 mm thick an colour having a tensile strength 550 mpa make uniix or jindal mectec or equivalent brand , synthetic paint enamelled og colour confirming to is 5 to 2004 make berger or asian or nerolac , painting brush 4 feet isi marked , nails various size , self taping steel screw half thread with rawl plug of 1 1 by 2 inch size isi marked 100 nos per pkt , anodised aluminium door 1000 mm x2100 double shutter with frame including all fittings and as directed make jindal or hindalco aluminium section weighing 0.55 kg per mtr , anodised aluminium window triple track 2 track glass and 1 track wire mesh with frame of size 1000mm x 1000mm including all fittings and as directed , anodised aluminium ventilator 1200x600 mm fixed type with glass 4mm thick thick including all fittings and as directed make jindal or hindalco aluminium section weighing 0.55 kg per mtr , ms anchor bolt, suitable for rcc work 12mm dia 300mm long with 2 washer and a nut minimum wt of each bolt and nut is 450 gm complete all as directed , ceramic tiles of size 600 mm x 600 mm for floor thickness between 9 to 10 mm thick make johnson or kajaria or orien 1st quality confroming to is 156 or 2006 , white cement confirming to is 8042 or 1989 make acc or birla white or ambuja , curtain arrangement drapery and rod made of 25 mm dia and 1600 mm long pre coated ms pipe with fancy type as per technical specification and drawing attached , cement opc 43 grade packed in hdpe bag each 50 kg wt make birla gold or ambuja or ultratech or acc or jk or dalmia or equivalent confirming to is 8112 to 2013 , coarse sand free from vegetation confirming to is 650 to 1991 reaffirmed 2008 , coarse aggregate 40mm graded confirming to is 383 to 2016 , stone boulder 9 feet to 12 feet confirming to is 1597 part i 1992 reaffirmed 2002 , pvc pipe 75mm dia 3 mtr long make prince or finolex or supreme or equivalent confirming to is 4985 to 2000 reaffirmed 2006 , construction material for drain and sump cement 43 grade opc packed in hdpe bag each 50 kg wt conform to is 8112 to 1989 make birla gold or ambuja or ultratech or acc or jk or dalmia or equivalent , coarse sand free from vegetation , coarse aggregate 40mm graded , hardcore 63 to 90 mm graded , brick sub class b , three phase 1.2 hp monoblock pump 430 volt complete with and incl 3 mtr length required size flexible suction pipe foot valve and connected accessories complete , distribution box 8 way spn 240 volts copper bus bar and neutral link earthing stud conforming to //bid details 2 / 95 is 13032 and is 8623 double door type make havells or legrand or l and t , mcb spn 240 volts 32 amps make havells or l and t or standard , mcb sp 6 to 32 amps make havells or l and t standard , pvc tape 19mm wide 5 m long make steelgrip or anchor or kinjal , cable pvc insulated electric cables heavy duty 1100 volts grade multi stranded coppe

CTN :45112925

18 May, 2026 NA

Shimla - Himachal Pradesh

Tender For tender for supply of disconnecting ht and lt supply taking down the defective transformer indoor outdoor type from four pole two pole structure or lifting from the outdoor type foundation or taking out from sub station bldg using a crane of suitable capacity and slings ropes etc as required and shifting the same to civil workshop for repairs complete all as directed for transformer capacity 400 kva , shifting back the repaired transformer indoor outdoor type from civil workshop to site reinstalling at original position and fixing properly on four pole two pole structure or outdoor type foundation or inside a sub station bldg using a crane of suitable capacity and slings ropes etc as required making ht lt side connections and testing for satisfactorily working complete all as directed for transformer of capacity 400 kva , draining out transformer oil from the transformer and storing the same in suitable containers to be arranged by contractor without any extra cost opening the top cover and lifting up the core assembly carefully to check the condition of transformer windings and core retanking the same after repairing checking of leakage from transformer body and repairing welding works required for making transformer body leak proof refilling the transformer oil dully dehydrated and filtered dehydration and filteration to be paid separately and making all connections with ht lt side bushings refixing the top cover and testing the transformer with a suitable capacity insulation tester complete all as directed for transformer of cap 400 kva , m and l for rewinding of burnt out defective ht copper coils with new super enamelled heavy duty copper winding wires of size matching to the existing one including varnishing drying in a suitable oven and all insulating material such as cotton sleeves tapes etc and connections with bushing terminals complete all as specified and directed , all as per item no 4 above but lt copper coils complete all as specified and directed , m and l for painting the transformer tank from inside with two coats of zinc chromite after preparing the tank walls bottom top cover inner side by properly cleaning the surfaces oil free complete all as directed for transformer capacity 400 kva , m and l for replacement of defective ht porcelain bushing of suitable size for transformer of cap 400 kva including washers of good quality complete all as specified and directed , m and l for replacement of defective lt porcelain bushing of suitable size for transformer of cap 400 kva including washers of good quality complete all as specified and directed , dehydration and filteration of transformer oil for indoor outdoor type transformers of any capacity at site using transformer oil filteration plant to improve di electric strength not less than 45 kv at 2 point 5 mm electrode gap complete all as directed note unit rate quoted shall be deemed to include the charges for hiring of oil filteration plant shifting to different locations at cantt area testing of samples of oil as per requirement and nothing extra will be paid on this account , s and f new transformer oil for replacement or topping up the level of oil having dielectric strength not less than 45 complete all as specified and directed

State Government

CTN :45114889

18 May, 2026 NA

Moradabad - Uttar Pradesh

Tender For providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - 132kv substation bilari and 132kv substation kundarki under etd i moradabad; transformer oil centrifuging , cb timing test and equipment painting work; service provider

Central Government/Public Sector

CTN :44925702

11 May, 2026 NA

Goa - Goa

Tender For corrigendum : supply of retrieval pump as per encl , nitrogen cylinder water capacity 50 ltrs approx , portable trolley for handling cylinder 100 kg approx , portable refrigerant leak detection kit as per encl , slider lever grease gun with all accessories as per encl , pistol grip grease gun with all accessories , set of files as per encl , set of forged pliers as per encl , circlip remover internal , circlip remover external , electric hand held manual engraving machine as per encl , automatic center punch as per encl , measuring tape steel 300 mm , sounding tape stainless steel as per encl , vice bench parallel 125 mm quick release type , vice bench parallel 150 mm , metal tool box as per encl , hot air blowers for improving insulation of panels , vaccum cleaner hand as per encl , industrial portable vaccum cleaner with 900 w motor , portable wet vaccum cleaner , portable spray painting gun machine , high pressure washer as per encl , multi range portable conductivity meter as per encl , portable ph meter with 0.1 ph resolution , clamp on ultrasonic flow meter pipe dia 50 200 mm , portable vibration meter as per encl , portable usb high speed dvd of reputed make , portable usb hard disk 1 tb of reputed make , snap on battery as per encl , portable digital multimeter , soldering iron 25 watt flux soldering wire 20 mtrs , digital insulation tester , battery capacity tester , ac dc clamp meter , digital oscilloscope , rf power meter , cable power detector , power quality analyser , optical power meter , endoscope set recording , snap on mirror uim2lm , magnifying lens with light , heavy duty magnets , buffing machine , portable electric grinder as per encl , portable heavy duty grinder as per encl , hydraulic nut cracker as per encl , screw stud extractor as per encl , digital clock as per encl , inclinometer , air blower as per encl , spring balance , spanner wheel 12 , battery powered 2.0 ton lister as per encl , bicycle , tricycle , snap on set of adjustable wrenches as per encl , snap on combination wrench set as per encl , snap on ratchet combination wrench set as per encl , snap on ring end wrench set as per encl , snap on open end wrench set as per encl , snap on insulated open wrench set as per encl , snap on insulated hex key of size mm 3 4 5 6 8 10 , impact socket set as per encl , snap on t shape speeder wrench as per encl , snap on l hexagonal short arm key set as per encl , snap on l hexagonal long arm key set as per encl , snap on pliers locking std grip curved jaw as per encl , universal wrench set snap and grip key wrench , heavy duty straight pipe wrench od size 6 8 12 24 48 . , heavy duty offset pipe wrench of size 14 18 24 inches , aluminium straight pipe wrench of size 10 12 and 18 one each , snap on interchangeable head typ torque wrench as per enc , universal torque wrench for 10 100 nm , cordless impact wrench as per encl , stroboscope as per encl , non contact digital tachometer , non contact thermometer as per encl , ultrasonic level detection kit as per encl , hydrocarbon analyzer for pol tanks as per encl , kitiwake coolant analysis kit as per encl , kitiwakelub oil analysis kit as per encl , pol lab test apparatus incl //bid details 2 / 95 accessories as per encl , universal temperature calibrator as per encl , portable high temp precision calibrator as per encl , smart press calibrator as per encl , portable hydraulic flushing kit as per encl , m25 spanner square typ , m20 spanner open end , foot pump as per encl , centre punch

State Government

CTN :45118897

23 May, 2026 NA

Srinagar - Jammu And Kashmir

Tender For supply of tinter am073 axalta , tinter am074 axalta , tinter am735 axalta , tinteram732 axalta , tinter am082 axalta , tinteram 7 axalta , tinter am1 axalta , tinter am032 axalta , binder ab150 axalta , binder ab160 axalta , binder ab385 axalta , binder ak350 axalta , binder ak100 axalta , clear 679s axalta , hardener 256s axalta , microfiber cloth , master wipe , palstic primer 810r , masking tape , dust mask , sandpaper 220 no , sanpaper 400 no , leather shine , sandpaper 80no disk type , sandpaper 180 no disk type , body filler , emery paper 80 no , emery paper 180 no , nc putty , ps grey , duco thinner , dull black , duco white , masking paper 24 inch , masking paper 18 inch , duco rubbing compond , writing brush , duco red , painting gun , malmal cloth , surfacer 1k primer , paint spray mask , sander , cleaning brush set , tack cloth , duco silver , dothi cloth , rtv tube jain tube , tail lamp bulb , tail lamp bulb double point 1016 , head lamp tube bulb 90 100 suitable for bolero , head lamp tube bulb 90 100 suitable for sx4 , head lump bulb suitable for ciaz , head lump bulb suitable for scorpio , head lump bulb suitable for safari , head lamp bulb honda city , brake lamp press type t5 , brake lamp press type t20 , brake lamp press type t21 , head lamp holder , car perfume , dash board polish , tyre polish 250 ml minimum , sulfuric acid concentrated , black seal for tubeless tyre , tubeless tyre valve , car body polish 200 ml , carbon cleaner spray 100 ml minimum , hand gloves comfort grip glove for workshop use , portable grinder blade smooth 4 inch , portable grinder blade rough 6 inch , grinder wheel 8 inch smooth , grinder wheel 8 inch rough , windshield cutting wire , foot mat universal rubber 4 piece , fuse micro 10 amp , fuse micro 15 amp , fuse micro 20 amp , insulation tape , electric welding rods , brass welding rods , elfy tube 2 gram , epoxy adhesive fevitite 180 ml kit , elgi gear oil gun 5 litre , velvet cloth golden colour , velvet cloth blue colour , towel cloth white , towel cloth grey , u foam 2 inch sheet , thread reel assorted colors , metal screw one half inch , metal screw 1 inch , metal screw 2 inch , calcium carbide , hydrometer , car washing shampoo concentrated , bastic tin pack of 250 gram //bid details 2 / 73

Central Government And Public Sector

CTN :45104682

12 May, 2026 NA

Bangalore - Karnataka

Tender For magnetic drum separator (double stage type) conforming to model/part no. efe-rwf-md-00 of electro flux equipments pvt ltd or model/part no. pml-917134510 of permanent magnet ltd or model/part no. bmx-369/1 of wesman engineering company pvt ltd, with the following specifications: technical specifications: 1. type of magnet: high power high gradient rare earth magnet (nd-fe-b) 2. magnet grade: n50 3. magnetic strength: minimum 3000-3500 gauss or higher at drum surface 4. maximum operating temperature: 80 deg c 5. separation efficiency: minimum 90% (preferably up to 95% or above) 6. drum material: stainless steel (ss) 7. drum diameter: 300 mm 8. drum width: 600 mm 9. number of drums: double10. drum surface hardness: 500-700 vickers drive system: 11) geared motor: 1.0 hp x 2 nos, 1440 rpm, 415v +/- 10%, 50 hz, 3 phase, continuous duty (s1), insulation class f or better 12) make of geared motor: premium make such as sew / bonfiglioli / nord or equivalent make 13) drive type: v-belt and pulley note: the supply consists of 1.complete unit with base frame, guards, fasteners and all accessories required forinstallation 2.suitable for continuous heavy-duty industrial operation 3. proper sealing arrangement to prevent dust ingress 4. anti-corrosive painting (except ss parts) 5. nameplate indicating model, serial number, year of manufacture and technical details (a) the bearings should be procured from authorised dealers and should be of skf/fag/ntn / timken / ina make only. (b) the firm should furnish bearing inspection certificate from manufacturers or their authorised testing agents along with the supply. (c) magnet strength certificate (gauss report) from manufacturer or nabl accredited lab to be furnished along with the supply. (d) material test certificate (mtc) for drum from nabl accredited lab to be furnished along with the supply. (e) warranty: warranty shall be 18 months from date of supply or 12 months from commissioning, whichever is earlier. (f) makes : electro flux / wesman / permanent magnet ltd only. [ warranty period: 18 months after the date of delivery ]

CTN :45116538

14 May, 2026 7.05 Lacs

Ibrahimpatnam - Andhra Pradesh

Tender For replacement of damaged m.s pipes of various sizes at various locations of hydrant, raw water, clarified, lp & hp water lines and air lines of unit-i and ii, replacement of g.i pipes of various sizes of drinking water lines from d.m.plant to service building and c.h.p.area and rectification of hydrant landing valves, water monitors, emulsifier deluge valves at stage-i, chp i&ii, cleaning of sprinkler nozzles at fuel oil pump house,painting of emulsifier system at transformer yard of unit-i & ii during the year 2026-27 from 01.04.2026 or date of commencement of work to 30.09.2026.

CTN :45092517

14 May, 2026 NA

Patiala - Punjab

Tender For supply of material for providing of different parking of ucoe staffand students at pup - m.s. channel ismc 100 x 50mm, m.s. sangal (chain kuppi) heavy, cutter blade 4" (extra power, top line), grinder wheel 4" (extra power, top line), red oxide primer (4 ltr) (asian, berger, nerolac, j & n, ici), s/e black paint (4 itr) ist quality (asian, berger, nerolac, j & n. ici), t.t. oil (1 ltr) pack, painting brush 3", cement (bag) (ultratech, shree ultra, bangur), coarse sand

Anti Corrosive Painting Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government/Public Sector

State Government

Central Government And Public Sector