Tender For auction sale of depot ferrous scrap - scrap loco parts consist of damper, axle box housing, spheri block, gear casing, side buffer, cow catcher, yoke pin, bushes , liner, modified link, spring holder were plate, axle guide, torque arm, sand box, iron pipe, rubber bush assly, plant for ¿ blower, sand holding bracket, coil spring, knuckle, clevis, clevis pin, screw coupling, lock, double rotary, knuckle pin, equalizer beam, compensating beam, link, short beam, long beam, sand ejector, dowel plate and ci and other attachments. location- a by 2
Tender For supply of antivibrationmounting pad, plasser part no.5018053-11mn55, make : machweld, cummins, plasser [ warranty period: 30 months after the date of delivery ] ]
Tender For supply of antivibrationmounting pad, conical mount, similar to part no sr-075-1023 of m/s sidwal, or similar to part no. ssk-0061-017 of m/s ess ess kay engg. or equivalent part no. used in other make rmpus, conforming to rdso specification no. rdso/pe/spec/ac/0061-2005 [rev.1], suitable for use in rmpus of lhb-type ac coaches. accepted make :- rdso approved makes only . [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted:max 8 lacs ] ]
Tender For supply of piston ring , large end brg , fuel pipe filter to pump , pipe tank to filter , nozzle , element , fuel filter element , antivibrationmounting , cylinder linner , pre filter element , small end bush , connecting rod bolt , gasket
Tender For supply of antivibrationmounting (avm) pads to cil part no.- 3413922 or resistoflex part no.-fm 500 s, material required for 1400 hp demu. [ warranty period: 30 months after the date of delivery ] ]
Tender For auction sale of depot miscellaneous scrap - scrap and unerviceable condemned antivibrationmounting (avm) in dismenteled and broken condition with,aluminium , ms and rubber attached of sort and sizes. (qty approx)
Tender For for electrical and communication engineering department lab equipments are required as per new syllabus - upgradation of labarotariesece department, 8051 micro controller kit operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., single phase induction motor1 hp, 230 v ac, 1500 rpm with loading arrangement 1 no.voltmeter: (0 300) v ac, 96 96 mm with input terminals 1 no.ammeter: (0 10) a ac, 96 96 mm with input terminals 1 no.wattmeter: 2 kw, 96 96 mm with input terminals 1 no.power factor meter: 96 96 mm with input terminals 1 no.auto transformer: 0 300 v, 1 variac 1 no.mcb: 2-pole, 40 a / 230 v ac 1 no.digital rpm indicator with proximity sensor 1 no.aluminium brake drum: 230 mm diameter 1 no.spring balance: (0 25) kg 02 nos.circuit diagram printed on front panel with instruments and connecting terminals.motor and loading arrangement mounted on rigidchannel frame with anti-vibrationmounting pads, m12 1.5 bolt & nut, 85 mm dia 4 nos.mild steel powder-coated electrical panel tablesetup., auto transformerinput: 230 240 v ac, 50 hz.output: variable (0 270) v ac.rating: 1 kva.insulation class: class f / class h.construction: copper winding with carbon brush arrangement.mounting: bench-top / panel type.protection: suitable fuse / overload protection., dth trainer kitpower supply: 200 v to 240 v ac, 50 hz. dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m. controls: channel selection. volume control. fault simulation: five built-in simulated faults for troubleshooting experiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption. pcb size: 15" 12" with multicolour section-wise block diagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna. additional features: dth subscription connection with doordarshanfree channels., sim reader trainer kitpower supply: operates on 230 v ac 10%, 50 hz mains supply. built-in regulated smps power supply. operating dc supply: 5 v / 12 v with overload and short-circuit protection.sim card interface: supports gsm sim cards compatible with 2g / 3g / 4g / 5g networks. sim card read/write interface. supports sim card initialization, authentication, and communication functions. compatible with standard 6-pin / 8-pin sim card sockets.communication interface: usb 2.0 interface for pc communication. rs-232 serial communication interface. uart communication facility for embedded system interfacing.sim operating parameters: selectable sim clock frequencies: 3.579 mhz 7.159 mhz 14.318 mhz sim supply voltage selection facility. sim reset and activation control. supported protocols and standards: gsm etsi 07.07 and etsi 07.05 at command support. iso/iec 7816 smart card communication support. sim communication command monitoring facility. hardware features: on-board sim card socket. led indication for: power status sim detection reset activity data transmission/r
Tender For supply of lab equipments - purchase of lab equipments, four stroke petrol engine test rig specifications: single cylinder, 4-stroke spark ignition, petrol engine. air cooled rope brake arrangement with spring balance for loading . speed :1500 3500rpm power 3 hp. panel board for measuring speed with power supply and tacho generator setup, burette with tank assembly. load test test rig kit . heavy-duty fabricated ms base frame anti-vibrationmounting arrangement powder-coated / painted finish , saybolt viscometer apparatus specifications: glass type: high-quality borosilicate glass tube. control type: manual energy regulator control. shape: rectangular bath with cylindrical test chamber. temperature range: ambient to 240 c oil bath temperature. humidity: up to 80% rh (non-condensing). power supply: 230 v ac, 50 hz. measuring range: 32 to 1000 sus(saybolt universal seconds). accuracy: as per astm d-88( 0.2 seconds). mounting type:benchtop. capacity:one cup(approximately 60 ml). control mode:manual operation. port size:standard orifice sizeas per astmd-88. features:oil bath with heater, thermoregulator, insulated outer body, orifice, receiver flask., cleveland open cup (coc) apparatus specifications: standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 c per minute (as per standard) temperature range: (-6 to 400) c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valve body: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation, pensky-martens closed cup apparatus specifications: standard compliance: astm d93 / is 1448 (part 21) type: pensky-martens closed cup (motorized, digital type preferred) test cup: brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system: heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) digital temperature display power supply: 230v ac, 50 hz safety: over-temperature cut-off flame safety control