Latest billboard panel scrap Tenders | Government billboard panel scrap Tenders

CTN :43102526

18 Dec, 2025 2.38 Lacs

Jaipur - Rajasthan

Tender For ward no. 21 in vidhadhar nagar in patak pachhad hanuman park sector 2 in installing open gym work - cross trainerproviding and fixing of cross trainer of size not less than 1140mm (length) x 625mm (width) x 1750mm. (height), to enhance the mobility of upper and lower limbs and improve the flexibility of joints. the main structure frame shall be made from g.i. pipe minimum of 80nb c class welded with m.s. round base plate at least 250 mm & 10mm thick. the handle frame shall be made up of at least 25nb c class g.i. pipe. the footrests shall be made from lldpe/aluminum casting material of size not less than 130 mm x 310mmx5mm thickness and mounted on m.s. plate of size 130mmx310mmx3mm thick. high tensile steel with galvanized nuts and bolts shall be used for assembly. the powder coating shall be done with pure polyester powders of ackzonoble/ berger/ nerolac paints with 60 to 70 micron thicknesses complete in all respect including fixing the m.s. holdfast in cement concrete to hold the whole structure, under the directions of engineer-in- charge to fulfill the functional requirement., seated pullerproviding and fixing of seated puller of size not less than 2400mm (length) x 800mm (width) x 2000mm. (height), to enhance the strength of upper limbs and the muscles in chest and back and promote cardio-pulmonary function. the main structure frame shall be made from g.i. pipe minimum of 100nb c class welded with m.s. round base plate at least 250 mm & 10mm thick. the handle frame shall be minimum of 32nb c class g.i. pipe. the seat frame minimum of 50nb c class g.i. pipe, closing caps shall be made up of lldpe/high quality fiber reinforced plastic material. high tensile steel with galvanized nuts & bolts shall be used for assembly. the powder coating shall be done with pure polyester powders of ackzonoble/ berger/ nerolac paints with 60 to 70 micron thickness complete in all respect including fixing the m.s. holdfast in cement concrete to hold the whole structure, under the directions of engineer-in-charge to fulfill the functional requirement., chest pressproviding and fixing of chest press of size not less than 2200mm (length) x 800mm (width) x 2000mm. (height), to enhance the strength of upper limbs and the muscles in chest & back and promote cardio pulmonary function. the main structure frame shall be made from g.i. pipe minimum of 100nb c class welded with m.s. round base plate at least 250 mm & 10mm thick. the handle frame shall be made up from at least 32nb c class g.i. pipe. the seats and back rests to be fitted on the outer frames shall be made up of m.s. sheet of size not less than 330mm x 300 mmx2mm thickness. closing caps shall be made up of lldpe/high quality fiber reinforced plastic material. high tensile steel with galvanized nuts & bolts shall be used for assembly. the powder coating shall be done with pure polyester powders from ackzonoble/ berger/ nerolac paints with 60 to 70 micron thickness complete in all respect including fixing the m.s. holdfast in cement concrete to hold the whole structure, under the directions of engineer-in-charge to fulfill the functional requirement., pommel horseproviding and fixing of pommel horse of size not less than 2150mm (length) x 800mm (width) x 800mm. (height), to enhance the flexibility of lower limbs, waist and abdomen. the main structure frame shall be made from g.i. pipe minimum of 80nb c class welded with m.s. round base plate at least 250 mm & 10mm thick. the handle frame be minimum of 32nb shall be made from c class g.i. pipe. closing caps shall be made up of high quality fiber reinforced plastic material. high tensile steel with galvanized nuts and bolts shall be used for assembly. the powder coating shall be done with pure polyester powder ackzonoble/ berger/ nerolac paints with 60 to70 micron thickness complete in all respect including fixing the m.s. holdfast in cement concrete to hold the whole structure, under the directions of engineer-in-

Central Government/Public Sector

CTN :43113817

09 Dec, 2025 NA

Ahmedabad - Gujarat

Tender For demolition of 13 nos. of g+2 storey rcc frame structure buildings and 04 nos. of stilt+3 storey rcc frame structure buildings including credit of serviceable materials & disposal of unserviceable materials of rbi at vasna, ahmedabad

Corporations And Associations And Others

CTN :43117081

17 Dec, 2025 67.97 Lacs

Delhi - Delhi

Tender For supply and installation of open gym equipments in najafgarh zone and central zone under mplads funds for various locations of parks in municipal corporation of delhi. - supply and installation of open gym equipments in najafgarh zone and central zone under mplads funds for various locations of parks in municipal corporation of delhi., seated puller /pull chair made from c class g.i pipe. dimensions: - 1900mm (length) x 740mm (width) x 1920mm. (height). safe area:- 1.2mtr x 3mtr. seated puller equipment made up of c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the center pipe is of 100nb made from c class g.i. pipe. bottom support is of m.s. round plate of dia 250 mm & 10mm thickness welded. all linkages are made up of 25nb c class g.i. pipe. the handle frame is of 32nb c class g.i. pipe. the seat frame is of 32nb c class g.i. pipe. to build structure bushes are used which are made from seamless pipe of 60mm o.d. and 5mm thickness as well as 60mm diameter solid bar bush used. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class. welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. foundation cover closing cap is made from injection moulded plastic lldpe / hdpe. the seats and back rests are fitted on the outer frames are made up of m.s. sheet of size 330 mm x 300 mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.closing caps are made up of from injection moulded plastic lldpe / hdpe.pins used of diameter 25mm and 17mm are made up from sae 8620 bright material. the bearings used are of 6205 2rs1 and 6203 2rs1 permanent lubricated sealed bearing of reputed brand.high tensile steel with galvanized nuts & bolts are used for assembly.thecirclips used for assembly are of a16. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)., cross trainer /elliptical exerciser dimensions: - 1320mm (length) x 600mm (width) x 1750mm. (height). safe area: - 1.77 x 1.2mtr. cross trainer equipment made from c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the main frame pipes are of 80nb c class g.i. pipe with single bend pipe with 250mm radius. the bottom support of m.s. round plate of dia 250 mm & 10mm thick. the handle frame is made up of 25nb c class g.i. pipe. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. to build structure bushes are used which are made from m.s. seamless pipe of 60mm od with 5 mm thickness. the footrests are made from injection moulded plastic lldpe / hdpe. closing caps are made up of injection moulded plastic lldpe / hdpe. pins used of diameter 35mm, 25mm, and 17mm are made up from sae 8620 bright .the bearings used are of 6007 2rs1 62052rs1 and 62032rs1 permanent lubricated sealed bearing of reputed brand. high tensile steel with galvanized nuts and bolts are used for assembly. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall b

State Government

CTN :43117877

22 Dec, 2025 3.00 Lacs

Rajgarh-Mp - Madhya Pradesh

Tender For purchase of furniture items - officer table :- providing and supplying table of size 5 x2 6 x2 6 with c-frame leg 200 mm wide made of aluminum profile and crca formed section having provision for wire management. top made of 18 mm thick bwr plywood finish with 1.0 mm thick. laminate, wooden edge banding of edges. dotted embossed cable duct and with single drawer (w-350 mm, h-165 mm, d-475 mm) with branded telecopic channel. all steel components are epoxy powder coated after seven tanks. anti-corrosion., officer chair :- supply and placing high back revolving chair size total height 1030-1115 mm, depth 685 mm width 590 mm seat hight 425-510 mm, 5- prong nilony base for stability twin wheel heavy duty caster for easy mobility under load hot pressed plywood with steel t-nuts for rigid fasting seat and back are covered with pp cover, sturdy steel colum gas lift for center support and seat height adjustment, telescopic abs cover over steel colum low cable center tilt mechanism and with single piece integral center tilt mechanism and with single piece integral skin pu arm rest, quality tapestry high density molded pu cushion., staff chair :- supply and placing staff chair size total height 850 mm depth 570 mm, width 550 mm seat hi=eight 440 mm, uinder structure cantilever type ms crca tube 1.6 mm thick. hot pressed plywood with steel t-nuts for rigid fastening. single piece integarl skin pu arm rest. quality tapestry. high density pu molded cushion. all steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface., waiting chair :- supply and placing waiting three seater fixed chair, size ; total length 1800 mm, total height 750 mm, total depth 630 mm and seat height 410 mm, made of ms crca press formed seat components duly seamless welded to get proper finish chrome plated handles & base. steel perforated ms moulded one piece seat and back fitted in moulded chrome plated side strips, three individual seat fitted on ms tube support of 75 mm x 35 mm, seat and bottom support are powder coated., computer table :- supply and fixing in position computer table (work station) having size length 900 mm, width 600 mm, height 760 mm, c-frame & tubular crca steel structure, fabrication involves only mig/tig & spot welding. top & shelf made of 18 mm thick bwr plywood finish with 1.0 mm thick. laminated, wooden edge banding of edge, shelf adjustable on steel brackets. removable tubular cpu stand and an embossed modesty panel below table top provided. provision for wire management, drum type leveler. all steel components are epoxy powder coated after seven tanks anti corrosion treatment of surface., plastic chair:- plastic arm chair for office, godrej almira :- godrej interio almira slim size 2 door steel almira, 4 shedves, size length 1828 mm, width 914 mm, water cooler :-cooling capacity- 5 ltr./hr.number of taps- 2color- whiteweight- 10 kg., cash counter:-office reception table & cash counter desk of woodenproduct dimensionslength 48 , width 24 , height 36 approx., record rack :-material- mild steelno. of shelves- 5 shelvesmount type- finish type color- greyusage/application- officerack type- open rackappearance- modernproduct type- pre standing unitassembly required- no, bench :- product dimensions12d x 48w x 18h centimetersmaterial- stainless steekframe material- stainless steelcolour- silverstyle- antiquesize- 48"l x 12.3"w x 18"h overall size: 48"l x 12.3"w x 18"h, digital electronic safe locker for office with auto lock function, anti-theft alarm and led displays size length 500 mm width 350 mm