Tender For supply of tata 407 bs iv brake adjuster,tata 407 bs iv brake pipe line,tata 407 bs iv brake shoe assembly,tata 407 bs iv brake shoe liner,tata 407 bs iv rod spring washer,tata 407 bs iv injector washer,tata 407 bs iv yoke with flange,tata 407 bs iv shekel pin front,stata 407 bs iv hekel pin lock pati,bolero camper bs vi tandem master assembly,bolero camper bs vi tandem master ely kit,bolero bs iv water pump assembly,tata winger tie rod end both side,tata winger bonnet cable,tat 1212 bs vi def filter,tat 1212 bs vi wiper blade,tata 407 bs vi def filter,tata 407 bs vi wiper blade,tata 407 bs vi front and rear brake shoe,maruti gypsy rod spring bush,maruti gypsy ignation switch with key,tata 1212 bs iv compressor seal,tata 1212 bs iv pull and push set,m c hero honda front mud flap,m c hear honda accelerator valve,m and m thar thermostat valve,m and m thar tie rod end,tata 1212 recovery dog clutch bearing,l t wire,tubeless puncher stripe,insulation tape
Tender For supply of spares for cane unloader of 5 ton capacity at hbl plant sugauli, east champaran and lauriya, west champaran, bihar - hydraulic cylinder for swl 5 ton cane unloader grab (left & right), seal kit for hydraulic cylinder of cane unloader grab, hydraulic hose pipe for hydraulic cylinder with both side fittings, pix-xel x p3/4” w.p 310 bar, length-450 mm, hydraulic hose pipe for hydraulic cylinder with both side fittings, pix-xel x p3/4” w.p 310 bar, length-550 mm, suction line filter (strainer sc3-040), make – hydroline, return line filter (92619 10 c/k 23018/fa57-10), make – parker, air breather (element s/e 20-25u), make – hydroline, brake drum coupling fbdgc dia. 250 mm, break liner 110 mm x 12 mm, steel wire rope 19 mm , construction 6/19 steel core, make- usha martin, u-clamp 19 mm
Tender For supply of set of brake liner with solid woven, asbestos based friction material, made from asbestos yarn, spun around brass wire as per is: 2742 (part-3) make : ferodo/compo/commando, details in enclosed annexure. [ warranty period: 12 months after the date of delivery ] ]
Tender For supply of diesel filter primary and secondary , banjo washer no 17 18 and 19 no , front hub check nut , front hub check nut lock , front hub oil seal , steering pull and push rod and assy , front axle lock , front axle left hand side uj cross , front axle dumper bush , front axle lt hand side u and l joint assy with lock , front brake pad , front brake caliper repair kit , caliper assy mounting bolt 12 no , front popular shaft uj cross assy , rear left hand side wheel cylinder assy , rear brake shoe liner with rivet , clutch plate , presser plate , release bearing , split pin , bolt 10 no , bolt 12 no , shocker bush , emery paper , old cloth , fog lamp assy with bulb , wiper blade , combination switch , black light assy right hand side , left wire 04 mm , plastic tap roll , pull push switch , wiper motor assy , fuse 10 15 and 20 no , head light assy rt hand side with bulb , self motor bush holder , self motor armature , self gear drive assy , female clip , door lock inner and outer * /bid number : gem/2026/b/7605542 + /dated: 01-06-2026 ' ' / bid document 1 / 32
Tender For auction sale of others - condemned released unserviceable cast iron items consisting of cylinder liner, cylinder head, turbo casing, piston, moulded brake blocks etc weighing approximately 30 mt. (1) sold on as is where is basis, available under the custody sse/dsl/kjm as declared vide ds-08 no 230627 dt. 18.05.2026. (2) location: bin no.11 at scrap yard dsl shed kjm. (3) delivery to be made on weighment basis only. (4) road approach available. (5) weighing facility is available at 8 km from the site. (6) purchasers should survey the material for road approach, location and quantity before bidding to the lot. after bidding no correspondence will be entertained. (7) segregation is not permitted.
Tender For supply of brake beam liner size- 115 x 45 x 5 mm. as per rdso's drg. no. wd-89033-s-01 alt-25 item no. 08. wd-89033-s-01 alt-25 item no. 08. spec: is 3885 pt.1 gr iv .(manufacturer's initial, month & year of manufacture marked by metal laser engraving in 6 mm type & 0.1 mm depth minimum on hidden surface). [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted:max 8 lacs ] ]