Tender For corrigendum : supply of spares for flow more make pump model m590 and f5823 d d ? g? g - discharge end casing, part no.m590 bd23 , shaft sleeve nde, part no.m590 bd32 , pump shaft, part no. m590 bd2 , gland half, part no.m-590 bd7 , water seal ring half, part no.m590 bd9 , shaft sleeve de, part no.m590 bd10 , neck bush, part no.m590 bd19 , large seating and bush, part no. m590 bd26 , balance valve, part no. m590 bd30 , balance valve cover, part no. m590 bd31 , bearing bush, part no.m590 bd40 , brg. cap and brg. body de and nde, part no.m590 bd41 , balancing water conn. line assy, part no. m590 bd48. , bearing housing nde, part no.f5823 1 , cover for brg. housing, part no.f5823 5 , shaft sleeve nde, part no.f5823 7 , water seal ring, part no.f5823 10 , balancing wearing ring, part no.f5823 12 , key for impeller, part no.f5823 17 , shaft sleeve de, part no.f5823 21 , brg. housing in board de, part no.f5823 22 , brg. lock washer, part no.f5823 24 , key for pump half coup., part no. f5823 26 , sleeve nut nde, part no.m590 bd33 , sleeve nut de, part no.m590 bd43 , stud bolt with nut and washer cap, part no.f5823 4 , sleeve nut and lock nut for sleeve nde, part no.f5823 6 , brg. lock nut, part no. f5823 25 , sleeve nut and lock nut for sleeve de, part no.f5823 31 , stud bolt with nut casing to gland, part no. f5823 36 ) /bid number : gem/2025/b/6846727 * /dated: 06-11-2025 & & / bid document 1 / 28
Tender For corrigendum : rate contract for purchase of various items for repair of failed distribution transformers at nigams workshop - alu lv strip (size as required) dpc(variable with base date 1.6.25), alu hv bare (size as required) semc(variable with base date 1.6.25), cotton tape 1, sleeve 1 mm, 20 mil paper 30, 4 mil paper 24, 4 mil paper 26, 4 mil paper32, 4 mil paper 30, gum, 10 mil paper 20, core clamping insulation 2 mm, yoke various sizes mm, common block various sizes mm, oil duct various sizes mm thickness, stick various sizes mm, wooden spacer 45x45x15 mm, spacer 45x45x3 mm, ring 136x201x2 mm, delta flat 480x30x5 mm, lv chips 380x6x1 mm, foot plate paper 2 mm, p.c phase barrier various size mm, nut g.i.various sizes, washer g.i.various sizes, bolt g.i.various sizes, delta wire various sizes, earthing patti 1 mm thickness tinned copper 20mmx1mm, aluminium flat various sizes mm, delta patti, sleeve 8 mm, sleeve 4 mm, sleeve 6 mm, sleeve 10 mm, sleeve 12 mm, sleeve 1.5 mm, sleeve 2 mm, 1/2 nut g.i., 1/2 lock nut g.i., 1/2 washer g.i., flux, solder wire, copper brazing rod, aluminium brazing rod, brazing powder (l&t), crepe tape 1, 1/2 bakelite, 3/8 bakelite, hv bushing (porcelain,), hv bushing (metal part) complete set, lv bushing (porcelain,), lv bushing (metal part) complete set, ehv grade type-ii transformer oil ( with drum )(variable with base date 1.6.25), prv valve (virat), pvc cap 1/2, ci cap 1.25, paint (green/red/yellow/white/blue), thinner, zinc chromate, cork washer 12x32mm,110x74mmx50x28mm, top cover gasket 50x50x6 mm, oil gauge prismatic glass various size, oil gauge gasket various sizes, oil gauge washervarious sizes, oil gauge nut various sizes, vent pipe gasket 110x110x3 mm, hv clamp, aluminium member, m.s nuts,bolts,washers various sizes, mccb for box 32 amp, mccb for box 40 amp, mccb for box 63 amp, mccb for single phase 25amp, mccb for single phase 40amp, mccb for single phase 63amp, mccb box gasket 500x250x5 mm, silica gel breather, hv bmc, arcing horn with strip & nut bolt, candles mom, backalite sheet 0.50 mm thickness 60x60 mm, u clamp 70 x 50 x 70 mm prv, u clamp ci cap 50x50x50 mm, cloth, lt internal/ oil immerged circuit breaker assorted rating, holdtite, 1/4x2.5 bolt brecker, 1/4 nut brecker, aluminium lugs (various sizes), paint gun, engraving machine, hv farma (size as required), lv farma (size as required), grinder cutter wheel 4, lt bushing box
Tender For corrigendum : supply of pin eccentric assembly cotter pin 3 by 32 inch x 7 by 8 inch pl no 15321083 , valve lever support shaft finish pl no 10120026 , air elbow cyl block to cyl head finish pl no 10120294 , special dowel air and exaust valve lever pl no 10210027 , spring seat pl no 10210520 , shaft air and exhast valve lever pl no 10210775 , special stud pl no 10210830 , adjusting screw of valve lever pl no 10211019 , thrust ball pl no 10211123 , push rod lifter seat pl no 10211123 , plain hex nut 5 by 8 inch 11 unc 2b pl no 15366169 , spring lock washer 3 by 8 pl no 15396125 , spring lock washer 1 by 2 pl no 15396149 , hex head cap screw size 1 by 2 inch 13 x 1 pont 1 by 2 inch pl no 15032139