Latest detail project report Tenders | Government detail project report Tenders

State Government

CTN :42949587

11 Dec, 2025 NA

Guntur - Andhra Pradesh

Tender For preparation of detailed project report (dpr) for polavaram nallamala sagar link project as per cwc guidelines including requisite investigations and other job works for obtaining all other statuatory clearances from government of india organisations

State Government

CTN :42999398

08 Dec, 2025 12.71 Lacs

Dharwad - Karnataka

Tender For consultancy service for conducting reconnaissance and detailed survey, investigation, preparation of design, drawing, estimates, preparation of detailed project report, preparation of dtp and land acquisition etc (for 44 pmksy works ).

CTN :43003474

15 Dec, 2025 NA

Bangalore - Karnataka

Tender For regarding the service tender for the selection of detailed project report and selection of project development and management consultants (pdmc) for propose to establishment of an information/lecture center on the life history of buddha in a new building located in kanaganhalli, chittapur taluk, kalaburagi district.

corporations/Associations/Others

CTN :42882696

05 Dec, 2025 3.75 Lacs

Davangere - Karnataka

Tender For corrigendum : preparation of detailed project report for construction of staff quarters at pj extension davangere

State Government

CTN :42993369

08 Dec, 2025 8.63 Lacs

Sawaimadhopur - Rajasthan

Tender For architectural consultancy services for the detail project report on renovation and upgradation of govt. district hospital sawai madhopur

CTN :42901829

09 Dec, 2025 NA

Coimbatore - Tamil Nadu

Tender For purchase of equipments - purchase of equipment, bench top glass insitu airlift photo bioreactor1. vessel capacity: 3 liter borosilicate glass (working volume: two to three liters maximum), vessel hxd ratio 4:1 (400x100mm)2. head plate & bottom plate moc: ss 316l3. ports in top plate: ph sensor; dissolved oxygen (do) sensor; pressure sensor; air in and draft tube; air out; acid/base; sampling; and addition port.4. mixing method: ring sparger to create airlift circulation inside the reactor for uniform mixing and better aeration.5. holders for sensor /adapter / blind stoppers in head plate: ph sensor holder; media double inlet for acid/base dosing; air sparger - ring type for airlift application without stirring, air out with exhaust filter and open/close valve; pressure sensor holder; sampling pipe; blind stopper for un used port; unique suitable ss puncturing needles for sampling, air in, air out, inoculum, feed addition.6. ports in bottom plate with stand: port for temperature sensor; heating finger u-tube heat exchanger; drain.7. holders for sensor / adapter / blind stoppers in bottom plate: holder for temperature sensor, heating finger, u-tube heat exchanger.8. sensors: temperature, gel filled sterilizable ph sensor, & pressure sensor.9. controls and display: modular independent system of ph, temperature, pressure with touch screen graphical display & control; two set point control of ph with three-point buffer auto calibration; aeration by flow meter 0-5lpm with air pump; sterilization controls up to 121 without steam generator along with pressure safety mechanism by independent pressure sensor and digital display & control; automatic digital pressure safety and over temperature safety cutoff and alarm; upgradable control system for future prospective as cstr reactor & dissolved oxygen (do).10. measurement and control range: ph: 2-14; process temperature: 20 to 60 ; sterilization temperature: up to 121 ; and pressure up to 15 psi.11. fixed speed peristaltic pump: for acid/base dosing with teflon non spring head. (2 nos)12. cooling system: chiller cum circulator. chiller temperature range 4 to 40 , bath capacity 5l to cool down the reactor after sterilization and to work process temperature below ambient condition.13. illumination system: two illumination assembly with variable intensity control (1000-3000 lux) around the reactor with independent control switch for photobioreactor, or other application and easy detachable if not in use. 14. essential accessories : silicon tubing for acid/base addition (10m); air in and sampling (10m); water circulation (5m); air vent filters 0.2 micron sterilizable (6nos); and silicon septum (25nos)15. starter kit: spare silicon-o-rings for head plate, bottom plate (1no each), all other ports (5nos each), alen key.16. warranty: one year17. support (must): unconditional onsite technical support shall be provided as and when needed. the supplier must provide complete installation and hands-on demonstration of the equipment at the user site upon delivery.18. the vendor should have a registered presence in india with an authorized local service provider in tamil nadu.

CTN :42922643

10 Dec, 2025 NA

Coimbatore - Tamil Nadu

Tender For purchase of equipments - purchase of equipment:chromatographic workstation with capillary injector, packed injector, and auto-sampler should be quoted. chromatography workstation instruments should be built with self-diagnostic features and active-time management tools for better productivity, general features of chromatography workstation: column oven can accommodate two columns with maximum temperature range up to 400 c with set point resolution of 0.1 c. it should support 20 ramps & maximum temperature ramp rates of 100 c /min. cool down of oven from 400 c to 50 c in less than 5 min. fully automated with electronic pneumatic control afc / ppc / epc (digital control) for injector gas afc/epc/ppc should provide optimum performance with all types of capillary columns. system should have the capability to install a minimum of three injection and four detector ports. capable of detecting h and o across 0.01% 100% ranges (i.e., both trace in a matrix and bulk near-pure streams) column oven: operational temperature range: ambient +10 to 400 c overheat protection: programmable up to 420 c injector port: split/spitless injector 1 no packed injector 1 no, maximum temperature: 400 c, pressure setting range 0 100 psi with control setpoint of 0.01psi for specified pressure range., carrier gas flow control should have constant flow, constant pressure modes and constant linear velocity. auto injector: automatic sample injector up to 15 vials 2 ml vial with crimp set 100 nos, detector: flame ionisation detector (fid) 1 no, minimum detectable quantity: 3 pgc/s or more liner dynamic range: 1 107, maximum acquisition rate: 4 ms (250hz), thermal conductivity detector, sensitivity: >40000 mv maximum acquisition rate: 4 ms, maximum operating temp: 400 cgas cylinders & fittings, gas sampling: zero air, h2, n2 and helium gas cylinder with 2-stage regulators, each 1 no. four-stage gas purification panel and gas tubing. quote a suitable gas sample injector apparatus for the analysis of co2 gas, gas standards and a suitable packed column quote a 6-port gas sampling valve suitable for both manual (through syringe) and auto injection (online) quote sample line, sample loop, heated lines, filters, safety hydrogen purging, and flow control of gas. calibration gasses: suitable gas standards such as ar, he, h2, o2, co and ch4 should be providedpc and ups: pc i5 (or higher), 8gb ram, 1tb hdd, 22-inch led monitor (or higher), ssd: 512 gb, windows 10 os (or higher), wired keyboard and mouse. laser printer b/w, online ups sine wave capacity of 5 kva with battery power backup of 1 hour should be provided by the supplier general terms and conditions:warranty: 3 years manufacturer s warranty certificate. vendor should be an authorised provider of sophisticated high-precision chromatograph workstation systems for the past 15 years or more with: a proven track record in multiple countries and national institutes standard quality certifications such (iso 9001) 5+ past installations of similar systems in india. compliance statement should be enclosed with the quotation. the installation should be done at free of cost. hands-on training for 1 day for two trainees (faculty and scholars) must be provided on operation, maintenance and troubleshooting to two to two-three persons at the site of installation. if required, hands-on training must also be given to our faculty/scholars at a later stage, without any financial commitment to university. the technical details of the quoted instrument must be available on the official website of the principal supplier. the vendor should provide the list of end-users (recent) with contact details. the vendor must submit the latest reference letters from their previous users. trained service engineers in india (with suitable certificates) for the quoted model must be readily available to resolve the technical problems. a list of recent scientific publications in reputed journals from the user institutions where the quoted mode

CTN :42975040

05 Dec, 2025 NA

Dhalai - Tripura

Tender For preparation of detailed project reports (dprs) as per latest guidelines of pmgsy etc. for rural road projects (including bridges, cross drainage structures) for the unconnected habitation under r.d gonda twisa division, dhalai tripura

CTN :42998480

08 Dec, 2025 10.00 Lacs

Dhalai - Tripura

Tender For preparation of detailed project reports (dprs) as per latest guidelines of pmgsy etc. for rural road projects (incl bridges,cross drainage structures) for the unconnected habitation under manu and chawmanu rd block area of r.d manu division, dhalai.

Central Government/Public Sector

CTN :41750083

12 Dec, 2025 NA

Lucknow - Uttar Pradesh

Tender For corrigendum : consultancy services for preparation of detailed project report (dpr) for construction of gola ring road in the state of uttar pradesh.

Detail Project Report Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

corporations/Associations/Others

State Government

Central Government/Public Sector