Tender For k thread profile full length gauge for lh screw, required size: go- 55 x 6.35 mm with 1 mmwear limit, thread angle = 30 degrees, ref. drg. no. rdso- sk- 79068 alt-08 & sk 99002 (details). material tool steel. is- 3748/90, hardness- 50 / 55 hrc. supply with calibration certificate- valid for min. 01 year issued from nabl approved lab [ warranty period: 30 months after the date of delivery ] ]
Tender For supply of tool kit set for loco pilots consisting one set of following items: - 1) hand hammer ball pin and cross pin with wooden handle - 800grm- 01 nos., 2) adjustable pipe wrench size-300mm-01 nos., 3) adjustable small spanner size-300mm-01 nos., 4) cutting plier size-200mm (8") -01 nos., 5) screw driver size-12.5 mm x 300mm-01 nos., 6) flate cold chisel size -150mm-01 nos., 7) pin punch size-150mm-01 nos., 8) ring spanner size 18x19-01 nos., 9) reley wedge set- 16 nos. (12 nos. push type and 04 clamp type), 10) bg flate tyre gauge-3 nos., 11) wooden gulli (4 inch)- 6 nos., 12) wooden gulli (2 inch)-6 nos., make taparia, bosch, jhalani, inder or similar [ warranty period: 30 months after the date of delivery ] ]
Tender For corrigendum : tender for supply of cotter pin , plate clamping , cylinder head , cylinder cover , valve protecting cap , strip sealing , seal , gasket , gasket long seal , seal gasket , rocker arm fulcrum , outer valve cone , thrust spring , gasket , locking ring , fuel pump , pump cylinder 23 dia , ring sealing , roller , coupling sleeve , gasket , seal ring , disc , ring seal round , filter pin , ring snap , washer for injector , gasket , hexagon bolt , cock rss , screw plug , seal ring , pump assy lub oil , ring butting 14 , bearing ball deep groove , slide ring seal coal , pump cooling water , pendulam ball bearing pos 43 , fitting key pos 50 , key , gauge charging air pressure 0 to 1 kg , fuel pressuregauge , lub oil pressuregauge , ermeto bulk head screw , square gasket , cock r55 f6xr3 8cu , locking ring , ring locking , magnetic shaft , overload relay 3point8a 6point00a , bearing shell two part complete
Tender For supply of plastic bib taps, pillar taps, angle valves & stop valves for hot & cold water services conforming to is 9763,waste fittings for washbasin and sinks as per is 2963,cast copper alloy screw down bib taps and stop valves for water services conforming to is 781,plastic bib taps, pillar taps, angle valves & stop valves for hot & cold water services conforming to is 9763,bathroom water shower (v2),s steel wire gauge 1.20m x 15m with 0.33 mm nominal dia,aluminium sliding boltt 200mm isi,aluminium sliding boltt 250mm isi,pvc swr pipe single socket 100 mm dia isi mark complete,pvc waste coupling 32mm,aluminium door handle 150mm isi,aluminium door handle 125mm isi,exotic laminated sheet 8 feet x4 feet x1mm isi,aluminium door handle 100mm isi,aluminium tower boltt 125mm isi,pvc inlet pipe connection with nuts 15mm dia x 600mm long,bracket for wash hand basin,gi wire cloth 0.56 m dia width 1.0 mm of 1 mtr wide 15 mtr each roll,curtain rod bracket stainless steel,curtain rod knob stainless steel,door seal aluminium,alumin
Tender For tn-mm-2170 supply of railway track material for private siding and marshalling yard of sstps suratgarh - cms crossing 1:8.5, 52kg to rdso drg. no. t-4867, cms crossing 52 kg 1 in 12 rdso drawing no. t-4734, slide chair plate 52 kg of 1: 8.5 (01 set= 20 nos. plate) railway drawing no. :- t-4968, combination fish plate 60 kg and 52 kg to rdso drg. no. t-696-699 (1 set = 2 pair (4 fish plate, 8 nut,8bolt), glued joint 60kg to rdso drg no. t-5843, glued insulated rail joint g-3(l) for 52 kg rail rdso no- t- 671, check rail set at 4.33 mtr. for 1 in 8.5 of crossing bg for 52 kg rdso drawing no. rt-4773, gauge tie plate 52 kg of 1:8.5 railway drawing no.:- t-5812, t-5812/1, t-5812/2, ms plate c/switch 52 kg of 1:8.5 for lever box railway drawing no.t-3901, bearing plate of c/switch 52 kg 1:8.5 (01 set= 06 nos.) railway drawing no. t-4869 to t-4874, fish plate for 52 kg rail 610 mm long rdso n0- t-(090)(one setcomprise of 2 nos. fish plate & 4 nos. fish bolt & nut), galvaized nut & lock nut id-no. 3/16 and bolt with flat&spring washer size(16x50x38 )mm as per rdso no eti/c/0073, gfn liner 60 kg to rdso drg. no. t-3706, 60s approach sleeper of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4786, 60s-1as approach sleeper of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4787, 60 -2as approach sleeper of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4788, 60-3a approach sleeper of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4789, 60-4a approch sleeper of point& crossing 1 in 8.5 52 /60 kg as per rdso n0.4790, sleeper n0.1 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4791, sleeper n0.2 of point& crossing 1 in 8.5 52 /60 kg as per rdso n0.4791, sleeper n0.3 of point& crossing 1 in 8.5 52 /60 kg as per rdso n0.4793, sleeper n0.4 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4794, sleeper n0.5 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4795, sleeper n0.6 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4796, sleeper n0.7 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4797, sleeper n0.8 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4798, sleeper n0.9 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4799, sleeper n0.1 0 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4800, sleeper n0. 1 1 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4801, sleeper n0.1 2 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4802, sleeper n0.1 3 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4803, sleeper n0.1 4 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4804, sleeper n0.1 5 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4805, sleeper n0.1 6 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4806, sleeper n0.1 7 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4807, sleeper n0.1 8 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4808, sleeper n0.1 9 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4809, sleeper n0.20 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4810, sleeper n0. 21 of point & crossing 1 in 8.5 52 /60 kg as per rdso n0.4811, sleeper n0.22 of point& crossing 1 in 8.5 52 /60 kg as per rdso n0.4812, stretcher bar of c/switch 52 kg of 1:8.5 (01 set= 06 nos.) railway drawing no.- t-4885- 86, t-4887-88, t-4889-90, rail dolly bg attachment for transportation of prc sleeper with insulated wheel, grsp for 1:8.5 t/out, 52 kg to rdso drg. no. t-4865, gfn liner rt-3707, gfn liner rt-3708, improved sej 60 kg with complete fitting (rt-4902) and with psc sleepers (rt-4149) for max. gap =80 mm(in single gap)(fittings- plate screw,washer,nut bolt,m.s. bracket,c.i. chair,check rails,tongue rails,stock rails,gap avoid rails,split pin etc. as per rdso numbers), 1 in 12 curved switch (lh turnout/rh turnout, 01 rh and 01 lh tounge rail length 12356 mm and stock rail 01 lh & 01 rh 13000 mm length) in 52 k
Tender For supply of railway track material for private siding and marshalling yard of sstps suratgarh - cms crossing 1:8.5, 52kg to rdso drg. no. t-4867, cms crossing 52 kg 1 in 12 rdso drawing no. t-4734, slide chair plate 52 kg of 1: 8.5 (01 set= 20 nos., plate) railway drawing no. :- t-4968, combination fish plate 60 kg and 52 kg to rdso drg., no. t-696-699 (1 set = 2 pair (4 fish plate, 8, nut,8bolt), glued joint 60kg to rdso drg no. t-5843, glued insulated rail joint g-3(l) for 52 kg rail rdso, no- t- 671, check rail set at 4.33 mtr. for 1 in 8.5 of crossing bg, for 52 kg rdso drawing no. rt-4773, gauge tie plate 52 kg of 1:8.5 railway drawing no.:-, t-5812, t-5812/1, t-5812/2, ms plate c/switch 52 kg of 1:8.5 for lever box, railway drawing no.t-3901, bearing plate of c/switch 52 kg 1:8.5 (01 set= 06, nos.) railway drawing no. t-4869 to t-4874, fish plate for 52 kg rail 610 mm long rdso n0- t-, 090)(one setcomprise of 2 nos. fish plate & 4, nos. fish bolt & nut), galvaized nut & lock nut id-no. 3/16 and bolt, with flat&spring washer size(16x50x38 )mm as, per rdso no eti/c/0073, gfn liner 60 kg to rdso drg. no. t-3706, 60s approach sleeper of point & crossing 1 in 8.5 52, 60 kg as per rdso n0.4786, 60s-1as approach sleeper of point & crossing 1 in 8.5, 52 /60 kg as per rdso n0.4787, 60 -2as approach sleeper of point & crossing 1 in 8.5, 52 /60 kg as per rdso n0.4788, 60-3a approach sleeper of point & crossing 1 in 8.5 52, 60 kg as per rdso n0.4789, 60-4a approch sleeper of point& crossing 1 in 8.5 52, 60 kg as per rdso n0.4790, sleeper n0.1 of point & crossing 1 in 8.5 52 /60 kg as, per rdso n0.4791, sleeper n0.2 of point& crossing 1 in 8.5 52 /60 kg as, per rdso n0.4791, sleeper n0.3 of point& crossing 1 in 8.5 52 /60 kg as, per rdso n0.4793, sleeper n0.4 of point & crossing 1 in 8.5 52 /60 kg as, per rdso n0.4794, sleeper n0.5 of point & crossing 1 in 8.5 52 /60 kg as, per rdso n0.4795, sleeper n0.6 of point & crossing 1 in 8.5 52 /60 kg as, per rdso n0.4796, sleeper n0.7 of point & crossing 1 in 8.5 52 /60 kg as, per rdso n0.4797, sleeper n0.8 of point & crossing 1 in 8.5 52 /60 kg as, per rdso n0.4798, sleeper n0.9 of point & crossing 1 in 8.5 52 /60 kg as, per rdso n0.4799, sleeper n0.1 0 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4800, sleeper n0. 1 1 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4801, sleeper n0.1 2 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4802, sleeper n0.1 3 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4803, sleeper n0.1 4 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4804, sleeper n0.1 5 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4805, sleeper n0.1 6 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4806, sleeper n0.1 7 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4807, sleeper n0.1 8 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4808, sleeper n0.1 9 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4809, sleeper n0.20 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4810, sleeper n0. 21 of point & crossing 1 in 8.5 52 /60 kg, as per rdso n0.4811, sleeper n0.22 of point& crossing 1 in 8.5 52 /60 kg as, per rdso n0.4812, stretcher bar of c/switch 52 kg of 1:8.5 (01 set= 06, nos.) railway drawing no.- t-4885- 86, t-4887-88, t-, 4889-90, rail dolly bg attachment for transportation of, prc sleeper with insulated wheel, grsp for 1:8.5 t/out, 52 kg to rdso drg. no. t-4865, gfn liner rt-3707, gfn liner rt-3708, improved sej 60 kg with complete fitting (rt-, 4902) and with psc sleepers (rt-4149) for max., gap =80 mm(in single gap), (fittings- plate screw,washer,nut bolt,m.s., bracket,c.i. chair,check rails,tongue, rails,stock rails,gap avoid rails,split pin etc., as per rdso numbers), 1 in 12 curved switch (lh turnout/rh turnout, 01, rh and 01 lh tounge rail length 12356 mm and stock, rail 01
Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr