Latest discrete component trainer Tenders | Government discrete component trainer Tenders

CTN :45601240

09 Jul, 2026 NA

Mumbai - Maharashtra

Tender For supply of 25baic003 boq d d - unloading cylinder with single pipe connection , socket cap screw , oil strainer with magnet filter , filter bag , bearing set for compressor motor , zinc plug , nuts & bolts , indicating lamp white led type , push button green , solenoid coil , zinc plug , pressure gauges water , hammer 2 kg , charging manifold modofied , shock mounts for accel smc 6 65 compressor 1set 32nos , thermometer 0 to 50 c , fuse 2 amp control fuse , drain valve , white indication lamp , oil strainer , neoprene o ring , oil level glass , hexagon head screw , spring washer , benzing ring , seeger ring , benzing ring , threaded plug , spring for unloading ring , valve spring , discharge valve assembly , gasket , screw , crank shaft , key , coupling piece , coupling pin , benzing ring , connecting rod assembly , castle nut , split pin , guide pin , piston with pin & ring set , piston pin , scraper ring , connecting rod bolt , shaft seal , tape heater , coil defrost heater , gasket set for condenser , low pressure cut out , oil pressure cut out , thermostat , thermostat , limit switch , filter drier , ref globe valve , back pressure valve , thermosatic expansion valve , burn out filter drier , liquid level gauge glass , drain valve , mcb dp 10 a , mcb sp 2 a , mcb dp 6 a , temperature gauge for sea water , pressure safty valve , oil filter , oil heater , high pressure gauge , pressure transmitter discharge , high pressure cutout , pilot solenoid valve , filter drier core , auxiliary contactor 3 no 1 nc , mccb 100 a , hmi color 7 inch , hrc fuse for compressor , oil seal , hex bolt , spring washer , gasket , washer , washer , washer , washer , hex bolt , hex bolt , spring washer , mech seal , grub screw , allen bolt , washer , washer , w asher , washer , hex bolt , hex bolt , spring washer , hex bolt , grease nipple , grub screw , allen bolt , dual pressure safety valve at condenser , vent valve 1 2 , water pressure gauge , chilled water line butterfly valve 50 nb , adjustable spanner 12 , pipe wrench 10 , insulated screw driver 8 , insulated screw driver 3 , insulated screw driver 6 , ratchet 1 4 , refrigerant gas leak detectors hand held , 3 pin plug socket 5 15 a with on off switch , cable gland pg 21 , cable gland pg 11 , cable gland pg 9 , cable gland pg 13 5 , cable gland pg 48 , cable gland pg 16 , cable gland pg 11 , cable gland pg 9 , screw driver 8 , screw driver 6 , adjustable spanner 8 , screw driver 10 , screw driver 12 , flat nose plier 6 , shock mounts akcc 60 , signal transducer rtd , rotor assembly bearing , motor protection relay 8 22 amp

CTN :45347634

27 Jun, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For corrigendum : tender for supply of vao card , door hatch sensor , vdmc , serial expension card , vrtu fan chassis , 12v power supply for vrtu , 5v power supply for vrtu , 16 slot vme chassis system , serial card rs232+rs485 tab 5 , marine isolator , battery pack for ups , ruggedized , 2.4kw dc ups power unit , keyboard , rugged panel mount 2 in trackball , gauge 48 mm 0 to 10 bar , gauge 48mm 0 to 150 c , gauge 48mm 0 to 750 c , gauge 72mm 0 to 10 bar , gauge 72mm 0 to 1250 rpm , gauge 72mm 0 to 1250 rpm with backlit , gauge 96 mm 0 to 250 rpm , gauge 96 mm 0 to 250 rpm with backlit , gauge 96 mm 20 to 40deg , top mount level transmitter normal temp , side mount leval transmitter normal temp , top leval transmitter high temp for bilge , top leval transmitter ht ss316 , side leval transmitter high temp , flood switch , totaliser for flow meter , pressure transducer (0-6 bar) , pressure transducer (0-10bar) , pressure transducer (0-250 bar) , portable operating unit , heat detector , lonisation smoke detector , optical smoke detector , marine mounting base , i.s lonisation smoke detector , i.s optical smoke detector , addressable base for is type sensors , i.s galvanic barrier , eeot - dial type for engine room , eeot gong for engine room , eeot- push button type for ops , vrtu power redundancy diode , rugged panel mount 20 1 in lcd monitor , network switch , sfp module for network switch , cctv external camera , trigger pcb transciver , modulator 25 kw transceiver , data interface & processing unit type 2 , vrtu console signal splitter (2 pole relay)

CTN :45345533

18 Jun, 2026 10.15 Lacs

Lalpur - Gujarat

Tender For corrigendum : supply of bending machine conduit pipe , bus bar with brackets 1 mtr , cctv camera kit , ceiling fan coil winding machine , conduit pipe cutting and threading machines , control panel , digital multi meter , discrete component trainer , dmx controller 512 , ev charger home 1 phase input , ev charger 3 phase input , file half round 2nd cut 250 mm with handle , file round 2nd cut 150 mm with handle , knife switch dpdt fitted with fuse terminals 16 amp , knife switch tpdt fitted with fuse terminals 16 amp , ladder - tower 3 meters on tyre wheels - min 10ft - max. 30ft , lux meter lcd read out 0.05 to 7000 lumens with battery. , magnetic flux meter , mallet barwood , meter reading instrument mri , potential transformer 415 v, 50hz, pt ratio, 440v.110v,10va , power factor meter digital , primary current injection set , rcc pole with accessories , rechargeable battery 12v,100ah , rubber mat , single phase transformer , single phase variable auto transformer , smart meter 3 phase - smart energy meter , soft starter , solar dc pump 1 hp , solar panel with battery 18 watt , solar street light , solar traffic light , solid state solar base single phase energy meter , spanner d.e. set , tachometer analog type - 10000 rpm , three phase transformer , wheat stone bridge ) /bid number : gem/2026/b/7576252 * /dated: 27-05-2026 & & / bid document 1 / 40

CTN :45501064

02 Jul, 2026 20.00 Lacs

Bikaner - Rajasthan

Tender For notice inviting limited tendernotice no: 01/elect./2026/ 706 date:- 10.06.2026tools & equipments of –electrician trade- heavy duty screwdriver insulated , electrician screwdriver thin stem insulated handle, , knife double bladed electrician, , chisel firmer with wooden handle, , grease gun, , (a) crimping tool, , wire cutter and stripper, , hacksaw frame, , tweezers, , drill hand brace, , plane cutters, , smoothing cutters, , file flat rough, , file flat bastard, , file rasp, half round, , the soldering gun, , contactor & auxiliary contacts (rm), , contactor & auxiliary contacts. (rm), , pin type, shackle type, egg type & suspension type insulators including hardware fitting, , portable electric drill machine, , load bank (lamp/heater type), , brake test arrangement with two spring balance rating, , laboratory type induction coil, , series test lamp (rm), , knife switch dpdt fitted with fuse terminals (rm), , knife switch tpdt fitted with fuse terminals (rm), , miniature circuit breaker (rm), , earth plate (rm), , earth electrode (rm), , elcb and rccb (rm), , fuses (rm), , rheostat (sliding type), , capacitors (rm), , various electronic components (rm), , various lamps (rm), , plug socket piano switch lamp, , holder (rm), , cables:, , twisted pair, , non-metallic sheathed cable, , underground feeder cable, , ribbon cable, , metallic sheathed cable multi-, , conductor cable coaxial cable, , direct-buried cable (rm), , rubber mat (rm), , electrician helmet, , rcc pole with accessories (ms angle iron, 'c' clamp, stay insulator etc.) and materials, , quipment, , ohm meter; series type & shunt type, portable box type, , digital multi meter, , a.c. voltmeter m.i. analog, portable box type housed in bakelite case, , milli voltmeter centre zero analog, portable box type housed in bakelite case, , ammeter mc analog, portable box type housed in bakelite case, , ac ammeter mi, analog, portable box type housed in bakelite case, , weight wattmeter analog, , (b) frequency meter (digital), , magnetic flux meter, , tachometer, , tong tester / clamp meter, , megger, , single phase variable auto transformer, , growler, , ac starters: :- -, , f. star delta starter soft starter, , g. auto transformer type, , oscilloscope dual trace, , function generator, , discrete component trainer, , linear i.c. trainer, , digital i.c. trainer, , domestic appliances -, , g. mixture & grinder, , h. washing machine semi-automatic, , i. motor pump set, , oil testing kit, , battery charger, , current transformer, , potential transformer, , 1 5 or 17 computer or latest version, , d.c. shunt generator with control panel, , motor-generator (ac to dc) with control panel, , d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker, , dc series motor coupled with spring balance load with control pannel, , dc shunt motor with control pannel, , dc shunt motor with control pannel, , dc compound motor with starter and switch with control pannel, , motor generator(dc to ac) set consisting of - shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed, , plate, fixing bolts, foundation bolts and flexible coupling., , ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load., , ac phase-wound slip ring motor with starter switch, , universal motor with starter/switch, , synchronous motor with accessories like starter, excitation arrangements., , thyristor /igbt controlled d.c., , motor drive with tacho-generator feedback arrangement, , thyristor/igbt controlled a.c. motor drive with, , single phase transformer, core type, air cooled, , three phase transformer, shell type oil cooled with delta/ star, , electrical machine trainer -, , diesel generator set with changeover switch, ov

CTN :45481843

03 Jul, 2026 NA

Bangalore - Karnataka

Tender For realization of signal conditioning card (npr-001) of spacecraft pressure transducer (idpt)

CTN :45475071

15 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For purchase of non-consumables for ece department - purchase, dual output regulated dc variable power supply input voltage: 230v/50 hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., function generator frequency range: 0.1 hz to 5 mhz. display: 4 to 6 digit led display. output waveforms: sine, triangle, square, pulse, ramp. amplitude: 0 20 vpp. rise time: 100 ns. distortion: 1% within specified frequency range. power supply: 230 v ac 10%, 50 60 hz. output amplifier protection: short-circuit and 15 v overload protection. dc offset: 0 to 10 v adjustable. attenuation: 0 to 60 db., dso (digital storage oscilloscope) bandwidth: 50 100 mhz. sampling rate: 1 gs/s. channels: 2 (minimum). power supply: 100 240 v ac, 50 60 hz. automatic measurements: vpp, vavg, vrms, frequency, period, vmax, vmin, rise time, fall time, +width, width, +duty, duty, etc. horizontal scale: 5 ns/div 50 s/div or equivalent. vertical resolution: 8 bits (2 channelssimultaneously). vertical sensitivity: 1 mv/div 10 v/div (at input). waveform math: +, , , , invert, fft, etc. waveform storage: 16 waveforms or equivalent. communication interface: usb host and usb interface. display: 7-inch color display or equivalent. input impedance: 1 m 2% || 20 pf. accessories: 2 passive probes (1x/10x)., digital ic trainer kit with breadboard +5 v dc, 1 a regulated power supply. 12 v dc / 15 v dc, 200 ma regulated power supply. solderless breadboard with minimum 840 tie points,power distribution buses. zif (zero insertion force) ic sockets to accommodate 8 or 16 pin ics. logic input and output leds for output monitoring. 16 buffered led outputs. 16 debounced switch inputs. variable clock generator: 0.5 hz to 50 hz. single pulse output: 100 ms (buffered, positive and negative outputs). one seven-segment display with 4 bcd inputs. built-in logic switches. manual clock: debounced push-button (one pulse per press)., lvdt trainer kit ac mains power supply: 230 v 10%, 50 hz. fixed regulated dc power supply: +5 v, 12 v / 500 ma. transducer: lvdt. lvdt displacement: 20 mm (40 mm total). displacement scale: linear 20 mm. displacement display: red color 3 digit led display. excitation frequency: 4 khz. excitation voltage: ac variable excitation voltage up to 5 v., strain guage trainer kit ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual.

CTN :45465678

19 Jun, 2026 NA

Kanchipuram - Tamil Nadu

Tender For supply, installation and testing of electronic equipments - supply -ece lab equipments, single output regulated dcvariable power supply- input voltage: 230v / 50hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., dual output regulated dc variable power supply- input voltage: 230v/50 hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., function generator - frequency range: 0.1 hz to 5 mhz. display: 4 to 6 digit led display. output waveforms: sine, triangle, square, pulse, ramp. amplitude: 0 20 vpp. rise time: 100 ns. distortion: 1% within specified frequency range. power supply: 230 v ac 10%, 50 60 hz. output amplifier protection: short-circuit and 15 v, digital ic trainer kit with breadboard - +5 v dc, 1 a regulated power supply. 12 v dc / 15 v dc, 200 ma regulated power supply. solderless breadboard with minimum 840 tie- points,power distribution buses. zif (zero insertion force) ic sockets to accommodate 8 or 16 pin ics. logic input and output leds for output monitoring. 16 buffered led outputs. 16 debounced switch inputs. variable clock generator: 0.5 hz to 50 hz. single pulse output: 100 ms (buffered, positive and negative outputs). one seven-segment display with 4 bcd inputs. built-in logic switches. manual clock: debounced push-button (one pulseper press)., dc voltmeter(digital) - dc digital voltmeter - 3 digit led/lcd display, measurement range: 0 20 v dc,accuracy: class 0.5( 0.5 % full-scale), dc ammeter - dc ammeter digital - 3 digit led/lcd display, measurement range: 0 5 a dc,accuracy: class 0.5 ( 0.5 % full-scale), lvdttrainer kit - ac mains power supply: 230 v 10%, 50 hz. fixed regulated dc power supply: +5 v, 12 v / 500 ma. transducer: lvdt. lvdt displacement: 20 mm (40 mm total). displacement scale: linear 20 mm. displacement display: red color 3 digit led display. excitation frequency: 4 khz. excitation voltage: ac variable excitation voltage up to 5 v., strain gauge trainer kit - ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. instrumentation amplifiers with 3 digit display for strain / output voltage. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual., ask modulation and demodulation kit - message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz, amplitude 5 v. supply voltage (board): +12 v, +5 v dc. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., fpga trainer kit - must use industry-standard mid-range fpga device usb-jtag programmable, compatible with vivado ise (webpack). power supply: 5 v dc through usb or external adapter. on-board peripherals: leds, switches, push buttons, 7-segment display,clock source, gpio / pmod expansion ports, uart, vga / hdmi, usb- uart bridge, usb cable. user manual., measurement scale: a vertical steel meter scale, usually with (1mm) graduations, for precise deflection measurement., accessories: includes a set of slotted weights (e.g., (6times 50g) or similar sets) for incremental loading.

CTN :45365473

13 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For purchase of lab equipments for ice dept - purchase of lab equipments for ice dept, i/p and p/i converter (iemcode:g002) i/p converter:(4 20) ma to (3 15) psi conversion. p/i converter:(3 15) psi to (4 20) ma conversion. air filter regulator (afr):20 psi regulated air supply. built-in current source. 3 digit led display for process indication. power supply: 230 v ac, 50 hz. mounting:bench-top / panel-mounted trainer configuration., level measurement using float and sight glass indicator- itemcode: g005specifications: sight glass level indicator. float type level indicator. power supply:230 v ac, 50 hz. monoblock pump:0.5 hp / 1 hp. sump tank., 8051develop ment board with usb/rs 232 cable to connect with computer (item code: g008)specifications: communication interface:usb / rs-232. on-board facilities:8 output leds,8 input switches,ldr,reed switch,8-bit adc,8-bit dac. display interfaces:seven-segment display,16 2 lcd interface. motor interfacing:stepper motor with driver,dc motor with h-bridge driver, 8 bit adc/dac interface board (item code: g009)specifications: thermistor / lm35 input in one channel. variable input (0 5) v in another channel. 8 leds for digital output indication.. necessary control signals provided for adc0809. 8-bit dac using dac0808. 8-bit digital input from controller. single-channel dac output:(0 10) v. power supply: 12 v or 15 v for analog circuitry, water level measurement trainer kit using capacitive type transducer (item code: g020) tabletop model with transparent acrylic tank of approximately 50 cm height. capacitive type level sensor for continuous level measurement. sensor output: (4 20) ma and/or (0 5) v with built-in signal conditioning. vertical pump for water circulation from sump to tank. flow control valve, overflow, and drainage arrangement. digital display for water level indication in cm. power supply: 230 v ac, 50 hz, single phase. in-built regulated dc power supply for sensor and control circuit. mounted on powder-coated ms frame for laboratory use. suitable for calibration and study of capacitive level measurement., flow measurement using electromagn etic flow meter(item code: g021)specifications: medium: water (salt water / bore well water). electromagnetic flow measurement: instantaneous flow rate and totalized flow indication. electromagnetic flow meter: integral mounted type. power supply: 90 260 v ac, 50 hz. minimum media conductivity: 15 s/cm. flow rate unit: m /hr. operating pressure: up to 10 kg/cm . electrode material: ss-304 / ss-316 / ss 316l. lining material: ptfe / neoprene / hard rubber / pfa. line size: 15 nb 25 nb. flow range: 0.1 10 m /hr. connection type: flanged. display: digital indication for flow rate and totalized flow. water pump: submersible type, 230 v ac, 50 hz. water tank: approximately 20 25 liters capacity. flow control valve provided. drain valve and overflow arrangement provided. mounted on powder-coated ms frame suitable for laboratory use.

CTN :45332966

11 Jun, 2026 NA

Rourkela - Odisha

Tender For supply of electrician screwdriver thin stem insulated handle , electrician screwdriver thin stem insulated handle , knife double bladed electrician , neon tester , blow lamp brass , crimping tool , wire cutter and stripper , copper bit soldering iron , de soldering gun , contactor and auxiliary contacts , limit switch , rotary switch , relay cut out relays reverse current relays over current relays under voltage relays , pin type shackle type egg type and suspension type insulators , hydrometer , portable electric drill machine , load bank lamp or heater type , laboratory type induction coil , out side micrometer , knife switch dpdt fitted with fuse terminals , knife switch tpdt fitted with fuse terminals , earth plate , earth electrode , mccb , elcb , rccb , fuses , rheostat sliding type , capacitors , various lamps , bus bar with brackets , rubber mat , electrician helmet , safety belt , ohm meter series type and shunt type portable box type , digital multi meter , a c voltmeter m i analog portable box type housed in bakelite case , milli voltmeter centre zero analog portable box type housed in bakelite case , ammeter mc analog, portable box type housed in bakelite case , ac ammeter mi analog portable box type housed in bakelite case , kilo wattmeter analog , digital wattmeter , a c energy meter , power factor meter digital , frequency meter , magnetic flux meter , lux meter , tachometer , tong tester or clamp meter , megger , 3 point d c starter , 4 point d c starter , wheat stone bridge with galvanometer and battery , single phase variable auto transformer , phase sequence indicator , growler , ac starters , oscilloscope dual trace , function generator , soldering iron , temperature controlled soldering iron , discrete component trainer , linear i c trainer , digital i c trainer , electric induction plate , electric kettle , electric iron , immersion heater , a c ceiling fan and ac table fan , geyser storage type , mixture and grinder , washing machine semi-automatic , motor pump set , inverter with battery , voltage stabilizer , dc power supply , battery charger , current transformer , potential transformer , solar panel with battery , ink jet or laser printer , dc compound motor with starter and switch , thyristor igbt controlled d.c. motor drive with tacho generator feedback arrangement , thyristor igbt controlled a.c. motor drive with , electrical machine trainer , used dc generators series shunt and compound type for overhauling practice , motorised bench grinder , manual motor coil winding machine , ceiling fan coil winding machine , primary current injection set , stepper motor with digital controller , shaded pole motor , smart meter , ev charger , ev charger home , portable double telescopic ladder , 3 ph variac , rotary hammer drill 1 ph , lcr meter

CTN :45326580

09 Jun, 2026 NA

Madurai - Tamil Nadu

Tender For purchase of instrumentation and control engineering practices (equipment) - motorized control valve trainer kit signal input:4 20 ma or 0 5 v valve characteristic:equal percentage stem movement:maximum 10 mm or 12 mm body material:cast iron trim material:ss 316 trim size: cv value:2 or 5 actuator:servo motor supply voltage:230 v ac, 50 hz connection: flanged or screwed type. digital indicator provided potentiometer provided for varying the 4 20 ma input signal, saybolt viscometer apparatus glass type: high-quality borosilicate glass tube. control type: manual energy regulator control. shape: rectangular bath with cylindrical test chamber. temperature range: ambient to 240 c oil bath temperature. humidity: up to 80% rh (non-condensing). power supply: 230 v ac, 50 hz. measuring range: 32 to 1000 sus(saybolt universal seconds). accuracy: as per astm d-88( 0.2 seconds). mounting type:benchtop. capacity:one cup(approximately 60 ml). control mode:manual operation. port size:standard orifice sizeas per astm d-88. features:oil bath with heater,thermoregulator,insulated outer body,orifice,receiver flask, control valve trainer kit three pneumatic control valves provided with individual hand valves valve characteristics: i) quick opening ii) linear iii) equal percentage. valves connected in parallel configuration for comparative study. pneumatic operation with air supply connection. control valve assembly mounted on trainer panel. power supply: 230 v ac, 50 hz., water level measurement trainer kit using capacitive type transducer tabletop model with transparent acrylic tank of approximately 50 cm height. capacitive type level sensor for continuous level measurement. sensor output: (4 20)ma and/or (0 5)v with built-in signal conditioning. vertical pump for water circulation from sump to tank. flow control valve, overflow, and drainage arrangement. digital display for water level indication in cm. power supply: 230 v ac, 50 hz, single phase. in-built regulated dc power supply for sensor and control circuit. mounted on powder-coated ms frame for laboratory use. suitable for calibration and study of capacitive level measurement.

Discrete Component Trainer Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors