Latest drill tool Tenders | Government drill tool Tenders

Central Government/Public Sector

CTN :38005126

18 Nov, 2024 45.72 Lacs

Mundra - Gujarat

Tender For corrigendum : provn of 02 in nos bore wells alongwith associated items at icgs mundra - material and labour for drilling of 02 nos pilot/trial bore by direct rotary rig method including all t&p through any kind of starta (soil, kankar, boulder or soft or hard rock) down up to 150 m depth below ground level by using suitable drill bit according to levering of casing pipe including the cost of mud pit, channels, etc and disposal of soil obtained to a distance not exc. 1 km away complete all as specified. note:- (i) the drilling shall be continued up to specified depth and in case sticky clay occurs in between the drilling must be stopped and hydrologist of gws & sb shall be contacted & eggr-in-charge shall be informed.(ii)cost of this consultant shall be borne by contractor (iii) taking the samples from the bore well cutting for every 3 meter interval and every change in strata if less than 3meter. (iv) preparation of litho logs based on these samples.(v) drill time log to be prepared and prescribed., (vi) aquifer performance tests at constant discharge with draw down and recovery reading.(vii) after completion of pilot bore, the contractor shall have to arrange for electro eater logging test of each bore.(viii) contractor have also produced bore well water test report for drinking water parameters before levering of motor and pump.(note:- if water quality not found fit for domestic purpose use then all other connected items of trial bore will not be executed.) , supply assembling, jointing, lowering and fixing in the bore hole pvc casing pipe of nominal dia 315 mm (medium well) ,10 kg/cm2 working pressure, confirming to is 4985-2000 including providing pea gravel of 8 mm to 4.6mm size for packing around the casing/slotted pipe in bore well all as specified and directed. make: astral/ashirwad/ajay/sfmc, all as per item no 2.00 above but slotted pipe. , supply, assembling, jointing, lowering lead free pvc column pipes of nominal dia 65 mm, od 75 mm (min), non toxic, pressure 16 kg/cm2 with and including top and bottom adaptor (ss) and accessories like epdm ring and double ss stud all as spd and directed by engineer-in-charge. make: astral/ashirwad/ajay/sfmc, development of tube well with compressed air by means of air compressor of suitable capacity not less than 300 cfm and over pumping using suitable capacity pump to make available water free from turbidity complete all as specified and directed by engineer-in-charge., m & l for conducting yield test for the bore well by continuously pumping for 24 hours by using a submersible pump set to determine safe pumping yield and produced water test report of samples which is collect every hour complete as directed by the engineer-in-charge. [ all arrangements for yield test shall be made by contractor and cost for the same borne by contractor ], supply and fix ms reducer, bail plug, top cover made of 3mm thick ms plate for bore well in two half sections having a hole of 75 mm bore in centre to accommodate pvc pipe and submersible cable suitable for fixing to the pvc casing pipe top, electric logging and simple strata box including provision of 2 sets of ms clamps made of 50x6mm ms flat including nuts, bolts, etc. including one coat of epoxy primer and two coats of epoxy paint wherever necessary complete all as specified and directed by engineer-in-charge., supply, install, test and commissioning of submersible pump stainless steel body electric driven with submersible motor, water lubricate, 3 phase, 10.0hp (appx) 415 volts, 50 hz with suitable submersible electric motor suitable for discharge of 2 liters per second against total head of 125m in the bore complete all as specified and directed by the engineer-in-charge. [ note : column pipe, submersible cable and control gear will be measured and paid separately]. [make: kirloskar / crompton / ksb], supply, install, test and commissioning of submersible pump stainless steel body electric driven with submersible motor, wa

Central Government/Public Sector

CTN :38190548

19 Nov, 2024 NA

Prayagraj - Uttar Pradesh

Tender For supply of professional electrical drill tool set, 10 mm,500 watt, 100 pcs accessory set consisti ng -1 impact drill tool, claw hammer, pillers and knife, spirit level, wrench , drill bit for wood, steel and conc rete,screws , wall plugs, screw driving bits,and nut bits, power source -corded electric 230 volts. [ warrant y period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :38078223

19 Nov, 2024 9.07 Lacs

Chhindwara - Madhya Pradesh

Tender For supply of spares part for centralized ip based cctv surveillance system installed - ip ptz cam hikvision ds 2df8236i ael w , 8 channel nvr , 16 channel nvr , ip cctv bullet type , ip cctv dome type , power extention board , electrical drill tool set , 8 port poe network switch , 16 port poe network switch , 12 volt dc adapter 1 point 0 amp for cctv , 12 volt dc adapter 2 point 0 amp for cctv , cat 6 information outlet , self supporting slidig ladder

CTN :38108539

02 Dec, 2024 NA

Gorakhpur - Haryana

Tender For (1)supply of high availability single section digital axle counters(hassdac) with dual sensor system as per rdso spec. no:rdso/spn/177/2012 (ver.3) with dual track sensor device or latest amended up to date of tender opening. this includes the supply of high frequency web mounting type tx coil/rx coil- 04 nos., vr/pr box duly wired-02 nos., vital relays-04 nos., pr relays- 04 nos., clamp with deflector plates & hardware- 08 nos., dual display reset box with auto resetting facility- 02 nos., surge voltage protection d evices and filter card to be mounted on din rail etc- 02 nos. for complete installation & testing & commissio ning of (hassdac) system. note: one set of hassdac system will include equipment required to monitor one up line or one dn line of a full block section between two stations. (2) installation, testing & commissi oning of high availability single section digital axle counter (hassdac), single section type system complet e with track devices and other associated accessories to be ensured by oem. this include fixing of device, r elays, wiring, lacing/dressing, cable termination with lug eyelet, drilling holes in rails, installation of track d evices and make it functional along with existing ufsbi/block instrument. material required other than supp ly item of hassdac in item no. 1 above shall be arranged by firm to make it functional. [ warranty perio d: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :38122958

26 Nov, 2024 NA

Ahmedabad - Gujarat

Tender For supply of battery operated rail core drilling machine as per rdso specification no.tm/sm/468 dated 31.03.2014 first revision, 2017 with latest alteratio n (1) product specification erd35-2v50 max. core cutting 36mm, (2) rated speed 250/240 rpm (3) battery type li-on (4) battery voltage 50v (5) battery capa city (ah) 4.0, (6) no. of batteries supplied 02 nos (7) no. of charger supplied 1no (8) 01no special designed pressurized internal spindle cooling to give max lif e of core cutter and to avoid heating the rail, (9) 03 sets of standard rail drilling adapter for guage 60 (02nos), 52 (01no) provided with machine, (10) weight of machine with battery 20.0 kg, (11) 01no each special tct cutter 31.75mm & 26.5mm included as standard accessory (12) 01no each of tct core drill 31.7 5mm & 26.5mm included as standard accessory (13) dual speed 400 and 730 rpm (14) standard rail adaptor for 60 kg rail- 2 nos (15) supplied in kit box on e year onsite warranty, installation & training free of cost make eibenstock / milwaukee or equivalent ( 16) 10 nos.drill bit of size 28 mm. ( 10 x 20 = 200 nos .) ( the item is reserved for rdso approved sources only ) firm must upload technical data sheet compliance etc as per data sheet comp arision statement attached. accepted make for lakshmi brand with latest alteration 02 years warranty [ warranty period: 30 months after the dat e of delivery ]

Central Government/Public Sector

CTN :37996482

16 Nov, 2024 NA

Raigarh - Chhattisgarh

Tender For corrigendum : supply of portable grinding machine(mcode- m6220746021n pr- 100241780 lara item 10) , drilling machine (mcode m6215566001 pr- 100241780 lara item 20) , portable drilling machine (mcode- m6200000039 pr- 100241780 lara item 30) , portable grinding machine(mcode m2390171057 pr- 100241780 lara item 40)

Drill Tool Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector