Tender For corrigendum : supply of condenser coils for analyzer and mms shelters - copper condenser coil,1015 x 510 x 3rows , copper condenser coil,1110 x 760 x 3row , copper condenser coil,1470 x 1020x 3rows , hvac filter dml 165 , freon,r134a , compressor lube oil rl32h , dismantling, installation, testing and com
Tender For tender for supply of internal oil filter element , vibration eliminator flexible connection suction line , no element siemens 3tx4 010 2a , compressor oil heater , teflon seat washer 5/8inch , set of v belts , set of gaskets for condenser for 4 tr ref plant for nopv , ac voltmeter 0 to 500 vac 1.5 class rishabh type pq72 , thermosatatic expansion valve danfoss teat 20 20 , motor terminal plastic insulators , teflon seat washer 2-1/8inch , filter drier core for liquid injection line. , thermostatic expansion valve , size-3/8inch x 1/2inch flare , core for filter drier , hrc fuse link 4a , oil seal kit (mechanical seal ) for xrvn-127r4/165/26 , gasket set for condenser , kit for power contactor , valve angle type 1/4inch npt , tube steel o/d 8x1 thkx0.5m l , locking screw 1/8inch nptf part no. 05514 , compressor bock open reciprocating f14/1366bi r22 1000 rpm , tapered compr.ring 80x2 chr. part no 06367 , compressor suction pressure switch , condenser for 20 tr r22 ac plant for ekm submarine , locking screw 1/8inch nptf part no 05514 , seal plug 1/4inch nptf part no 05801 , selector switch salzer l&t 6a 250 v 2 p on/off , bearing front (nu216) , bearing rear (nup 216) , set shaft seal part no08012 , compressor discharge temp gauge , pressure gauge 65 dial -1 to 15 kg/cm2 for r134a , core for filter drier , aux contactor ge rl4r 4no coil-24v dc , solenoid valve danfoss evra15-24 v dc coil , push button siemens e-22 1 no+1 nc (red) , push button siemens e-22 1 no+1 nc (green) , allen bolt for nde inner bearing cover fixing part no.0051 , allen bolt for de inner bearing cover fixing part no.0050 , core for filter drier sporlan rp48bd , oil heater 1 kw with thermostat for 82.5 tr ac plant , semi conductor fuse m300115c 6.9 urd 30 d08 a0315 , cartridge for indufil duplex oil filter idgl-2-220 , water/seawater line differential pressure gauge cum switch , refrigerant line muffler plping and accessories of 144tr ac , shaft seal placement kit part no.kxs204 , cable gland size 4 , rhb/lht pre-load spring washer , vibration eliminator for discharge line , cable gland size 2 , star locating pin , cable gland size 6 , safety valve , control transformer tape wound 415 v/110 v 150 va , core for filter drier sporlan rc4864 , set of bearing for 7.5 kw motor for 2x2.1 tr ref plant , set of bearing for 1.5 kw motor for 2x2.1 tr ref plant , vibration eliminator 1-3/8inch ods , thermostatic expansion valve gfe-1zp charge 1/4inch x 1/2inch flar , valve check type 5/8inch ods , valve globe type 7/8inch ods , temp switch danfoss rt34-25 to 15 deg c , set of gaskets for condenser for 2 x 2.1 tr ref plant , set oilsump heat 80w 220-240v part no.08425 , set oil pump part no 08044 , set shaft seal part no 08008 , cw pressure gauges range 0 to 10 kg/cm 2 g , condenser , hrc fuses 100 amps , contactor 200 amps , push buttons , angle needle valve 1/4inch , level switch , compressor gauge , bolt hex head , hrc fuses for soft starter , screw driver 12inch , continuity tester , gasket set for condensor , temp switch , pressure switch xml a 0037 , lock nut m 120x2 km24 , ferrule id 10 steel , ferrule id8 steel , thermometer with brass shield 1/2inch bsp , rubber bonded washer , gasket , gasket , gasket , seal kit for filter assly , hooter ems0001016 24 v dc , aux contact ge rl4rd040td 5no coil 24v dc , bearing de nu 220 for 160 kw motor elmot , semi conductor fuses ge / feraaz 200a , 6.611 rd30-xx0315 , mc mccb ge 100a s 400a , with aux contact 2no+2nc , star contactor 415v ac with 1no+1nc coil voltage 110v ac , mc mccb ge 3pole 200a 415v ac s 2ka mc401 , catridge for indufil duplex oil filter model idgl-2-226 , emergency push button red 1no+1nc , lamp 380v ac red for lcp(siemens) , flexible gas charging line , megger , tong tester , gauge adopter 1/8inch fptx1/4inch sae , insulated screw driver 3inch , lube oil differential pressure switch , mccb siemens 3 pole type 3vl 3720-1dc36-0aa0-200a(55 ka) , teflon seat washer 1-5/8inch
Tender For supply of repair of compressor with related components , repair of ac condenser , repair of cooling coil , repair of expansion valve , repair of flashing and leaking test , ac gas refilling
Tender For supply of ac copper pipe 5 by 8 , totaline 1 by 4 inch copper pipe , copper tube 1 by 2inch , condenser coil for 1.5 tr for window ac outdoor unit , condenser coil for 1.5 tr for split ac outdoor unit , compressor 80 ltr 1 by 3 tr , compressor 150 ltrs 1 tr , compressor 2 tr ac rotary type , compressor 1.5 ltr rotary type , compressor 1 by 8 ltr for refrigerator , fan motor 1 by 10 hp for water cooler , fan motor for deep freezer , fan blade fpr outdoor unit for window type ac , fan motor 1 by 83 hp for water cooler , capillary filter 0.60 guage for ac , condenser coil 300 ltr for refrigerator , capillary filter 0.55 guage for ac
Tender For supply of repair of ac condenser , repair of compressor with related components , repair of cooling coil , repair of expansion valve , ac gas refilling , repair of flashing and leaking test
Tender For custom bid for services - comprehensive annual maintenance contract of cs12 eakon cold store located at doddanekundi plant acd for a period of 3 years -summary: comprehensive annual maintenance contract includes maintenance, repair/replacement of all the components of the cold stores as follows: a) compressor, condenser unit, evaporator unit, suitable refrigerant, power supply system, control system, all safety features, operator panel, different type of sensors, interconnecting piping including drainage water pipes, cold room panels, coil and drain heaters, doors, lighting, temperature recording panels, and all other electrical, mechanical as well as electronics components of the systems & eurotherm electronic recorder.b) detailed scope of work:1 vendor should take over the cold stores for camc, in as-is-conditions., 2) preventive maintenance (pm) of the units to be carried out every month in consultation with user / maintenance dept, and detailed pm schedule to be drawn up and a copy of the pm carried out (service report) should be forwarded to purchase department duly endorsed by maintenance dept. for the reference and records. this pm should be carried out apart from periodical servicing and attending the breakdown calls. 3) servicing of the units should be carried out once in every three months, within two weeks of commencement of the quarter. this should be carried out preferably on sundays/ holidays. this servicing involves cleaning of condensers, cooling coils, filters (if any) leakage testing & rectification; and any/all other works required to ensure proper functioning of the units. a copy of the service carried out (service report) should be forwarded to purchase dept. duly endorsed by user/ maintenance dept for the reference and records. 4) the firm should monitor the temperature/ attend breakdown / preventive maintenance or any other request from user/ maintenance /quality dept. & monitor the functioning of all the cold stores. the firm should monitor and record the cold store chamber temperature every hour during shift hours and should take signature on recorded values by user, quality dept /maintenance dept. daily. the camc vendor s scope of work will be active for three shifts per day/round the clock, including sundays & holidays, i.e. all days throughout the camc period. 5) the firm should inform all the three departments user/qa/maint. in the event of malfunctioning of the equipment is noticed. they also should ensure safety of the materials stored in the event of failure of the cold stores. 6) the firm should report any abnormality, breakdown, or any bypass made immediately to all the three dept viz user, maintenance and quality dept. the equipment uptime should be greater than 95% without any interruption. 7) the firm should inform to the maintenance department in the case power failure, so that maintenance dept. can arrange for switching on the dg supply. 8) the firm should able to read the temperature in the electronic temperature recorder. 9) the firm should attend any number of breakdown complaints as and when reported by user/ maintenance dept/ quality dept during the contract period. the breakdown complaints should be attended within 8 hrs from the receipt of oral or written complaints and the system should be rectified within a day, except for the major breakdowns. 10) the firm should bring all the tools and tackles necessary including consumables for the repair / servicing. 11) the firm should hand over the cold stores in good working condition after the completion of camc, failing which necessary remedial actions will be taken to recover loses to acd-hal by deducting equivalent amount from the due amount. c) monthly checks: checking and servicing of cold stores.- (a) compressors- condensing units, solenoid valves and all gauges, drier, globe valves and all gauges, hp/lp switches, oil pressure switches ., expansion valve and mixture., refrigerant level and top-up if required., oil le
Tender For providing of custom bid for services - sch a1 cleaning of return air filter and drain pipe and testing of cab ac,custom bid for services - sch b1 fault diagnosis and troubleshooting of cab ac,custom bid for services - sch b2 repairs to cab ac units in locomotives and fault findings and testing and brazing of copper pipes and gas charging in to ac equipment gasr407c,custom bid for services - sch b3 evaporator coilrepair,custom bid for services - sch b4 condenser coilrepair,custom bid for services - sch b5 rewinding of blower and condenser motors of roof mounted cab ac units,custom bid for services - sch c1 supply and fitment of hermetically sealed scroll compressor with make emerson climate zr28k3e tfd522,custom bid for services - sch c2 supply of condenser fan propeller type,custom bid for services - sch c3 supply of skf make bearing and overhauling of condenser and blower motor with skf make bearing,custom bid for services - sch c4 supply and fitement of control transformer 415 110v,custom bid for services - sch c5 s
Tender For corrigendum : supply of 3tr metal body copper coil evaporator and copper coil condenser ductable ac units , installation testing and commissioning of 3 tr ductable air conditioning units , supplying and laying of copper refrigerant pipes for 3 tr ductable ac units , extra for supply and charging of additional refrigerant gas , providing indoor unit ceiling mounting bracket system , supplying and laying of 2.5sq.mm 4 core pvc or xlpe insulated and pvc sheathed copper conductor unarmoured cable , supplying and installing 300 mm width x 50 mm depth x 1.6 mm thickness size perforated painted with powder coating m.s. cable trays , providing and laying of 40mm dia fire retardant corrosion free medium class u pvc pipe along with accessories , providing and laying of 32mm dia fire retardant corrosion free medium class u pvc pipe along with accessories , providing and laying of 25mm dia fire retardant corrosion free medium class u pvc pipe along with accessories , supply fabrication and installation of 22 swg gi sheet plenum duct complete with all accessories , supplying and fixing of powder coated extruded aluminium supply air grills with fixed front louvers bid number/ & ( * ) : gem/2025/b/5809058 dated/ + : 11-01-2025 bid document/ 2 2 1 / 18