Tender For state plan- works under nedumkandam section-state plan 2024-25 - energy efficiency improvement, optimization of electromechanical items, safety audit and ensuring safety in operation of wtps and pump houses- rwss to udumbanchola - supply, e - cost of materials & working charges, od70149/2024-2025:1. pump & motor -supply, erection, testing and commissioning of kwa pre-qualified reputed make centrifugal pump set with bronze/ss impeller, ss shaft and ci pump casing etc. complete. the duty condition is as follows, discharge - 6 lps & total head - 92m, the motor is tefc squirrel cage induction motor suitable for the above pump working with 3 phase, 50 hz, 415 v shall confirm to eefi/is 325 etc. complete including providing suitable concrete foundation including cost of cement., sand and metal etc. flexible coupling shall be used for coupling of pumps and motors. 2. starter - supply, erection, testing and commissioning of suitable rating fullu automatic star delta starter with air break contact starter suitable for the above motor with over voltage and under voltage protection, single phase preventer, over load relay with motor protection relay with main contactor and bypass contactor as per ie rules and code of practice etc. complete. 3. panelboard (suitable) for operating pump sets (but one pump set at a time) - supply, erection, testing and commissioning of cubical type floor mounted ms fabricated dust and vermin proof common control panelboard consisting of 1 no. suitable capacity mccb as incomer and 2 nos of suitable capacity mccb as out going (the two mccbs are interlocking with each other) providing suitable size aluminium bus bar inter connect the above mccbs and fitted with 3 nos of indicator lamps, 1 no. volt meter with selector switch, 1 no. ammeter with selector switch etc. complete and provided with a common earth bus for the entire panel and inter connect with the mccbs as per ie rules and code of practice. the panel shall be fitted on a common base frame on suitable foundation. 4. cabling work - supply, laying, testing and commissioning of suitable size cables for the above pump set from panelboard to starter and from starter to motor , considering energy conservation. 5 .earthing - supply of all materials and providing suitable earthing by using suitable size pipe/plate earthing gi/copper strip buried in ground and giving double earthing to motor, starter, panelboard etc. as per ie standards. 6. capacitor - supply, erection, testing and commissioning of heavy duty app capacitor for the motor to get a power factor above 0.95. the capacitor shall confirm to is 2834 . 7. valves - supply of suitable size best quality heavy duty isi marked ci double flanged sluice valve and non return valve with suitable pressure rating 8. suction and delivery pipe connections - the size of the suction pipe is suitable as per the site condition with a max length of 7.5m. suitable size foot valve connecting at the suction pipe bottom etc. complete and connecting the delivery side of the pump with the valves and suitable specials to connect with the pumping main.warranty 2 year (1 year warranty+ 1 year additional warranty), od109714/2024-2025:dismantling the existing old damged pump by disconnecting the cables, 15.2.1:demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in-charge.nominal concrete 1:3:6 or richer mix (i/c equivalent design mix), 4.3.1:centering and shuttering including strutting, propping etc. and removal of form work for:foundations, footings, bases for columns, 5.1.3:providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), 5.22.6:steel reinforcement for r.c.c work including straightening, cutting, bending, placing i
Tender For supply of material fro gp chichtola second call - list of material, metal 80 mm with royalti, metal 40 mm with royalti, metal 20 mm with royalti, churi 10 mm with royalti, sand with royalti, cement 53 grade isi mark ultratech, steel isi mark 6 mm, steel isi mark 8 mm, steel isi mark 10 mm, steel isi mark 12 mm, steel isi mark 16 mm, soil bricks std size, fly ash/cement bricks, supply of soft murum with royalti, supply of soil, tractor carting rent, carting of waste material, concrete mixture, excavator, static roller, water tanker, centering, ventilator, grill works, vetrified tiles, oil paint, birla white, distemper, pvc pipe 75 mm class 2, pvc pipe 90 mm class 2, pvc pipe 110 mm class 2, pvc pipe 140 mm class 2, pvc t and bend 75 mm, pvc t and bend 90 mm, paving block 60 mm, paving block 80 mm, toilet sheet traditional, centering wire and nails, steel door, steel windows, water pump, rcc pipe 1000 mm with collars, rcc pipe 800 mm with collars, rcc pipe 600 mm with collars, rcc pipe 450 mm with collars, rcc pipe 300 mm with collars, gi pipe 100 mm, gi socket 100 mm, gi pipe 150 mm, gi socket 150 mm, pvc socket 75 mm, pvc socket 90 mm, pvc socket 110 mm, pvc socket 140 mm, pvc t 40 mm, pvc socket 40 mm, pvc end cap 40 mm, pvc end cap 75 mm, pvc end cap 90 mm, pvc end cap 110 mm, pvc end cap 140 mm, air valve 50 mm, air valve 110 mm, air valve 140 and 130 mm, sluice valve 65 mm, sluice valve 50 mm, sluice valve 140 mm, 4 mm service wire, copper wire bunddle 1:18, holder, led light 25 watt, led light 20 watt, led light 14 watt, led light 12 watt, information board, steel sheet 12*4, cement sheet 12*4, cfl light 25 watts, cfl light 20 watts, fiber door, fencing wire, electric holder, auto switch, relay, bitumen 190 kg drum, checker tiles, water meter with installation and fitting complete, cement sitting chair, septic tank plastic, septic tank steel, solar lantern, toilet sheet kamod type, primer, ro + freezer complete set 1, solar pump 1 hp, solar pump 3 hp, solar panel, submercible pump 1hp, submercible pump 3hp, plastic slate for anganwadi childrens, compound wall net, steel angle, wooden door frame 3.5x7 ft, carpet, basin, steel cupboard, ceiling fan, capacitor, control panel, steel box, plywood sheet, copper wire bunddle 1:18, led /cfl light body cover, hand pump pipe g.i, hand pump pipe pvc, hand pump rod, hp bush, hp nut bolt, hp body cover, hp chain, hand pump bearing, hand pump chain, gate steel, asbestos sheet, 100 w flood light
Tender For for electrical and communication engineering department lab equipments are required as per new syllabus - upgradation of labarotariesece department, 8051 micro controller kit operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., single phase induction motor1 hp, 230 v ac, 1500 rpm with loading arrangement 1 no.voltmeter: (0 300) v ac, 96 96 mm with input terminals 1 no.ammeter: (0 10) a ac, 96 96 mm with input terminals 1 no.wattmeter: 2 kw, 96 96 mm with input terminals 1 no.power factor meter: 96 96 mm with input terminals 1 no.auto transformer: 0 300 v, 1 variac 1 no.mcb: 2-pole, 40 a / 230 v ac 1 no.digital rpm indicator with proximity sensor 1 no.aluminium brake drum: 230 mm diameter 1 no.spring balance: (0 25) kg 02 nos.circuit diagram printed on front panel with instruments and connecting terminals.motor and loading arrangement mounted on rigidchannel frame with anti-vibration mounting pads, m12 1.5 bolt & nut, 85 mm dia 4 nos.mild steel powder-coated electricalpanel tablesetup., auto transformerinput: 230 240 v ac, 50 hz.output: variable (0 270) v ac.rating: 1 kva.insulation class: class f / class h.construction: copper winding with carbon brush arrangement.mounting: bench-top / panel type.protection: suitable fuse / overload protection., dth trainer kitpower supply: 200 v to 240 v ac, 50 hz. dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m. controls: channel selection. volume control. fault simulation: five built-in simulated faults for troubleshooting experiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption. pcb size: 15" 12" with multicolour section-wise block diagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna. additional features: dth subscription connection with doordarshanfree channels., sim reader trainer kitpower supply: operates on 230 v ac 10%, 50 hz mains supply. built-in regulated smps power supply. operating dc supply: 5 v / 12 v with overload and short-circuit protection.sim card interface: supports gsm sim cards compatible with 2g / 3g / 4g / 5g networks. sim card read/write interface. supports sim card initialization, authentication, and communication functions. compatible with standard 6-pin / 8-pin sim card sockets.communication interface: usb 2.0 interface for pc communication. rs-232 serial communication interface. uart communication facility for embedded system interfacing.sim operating parameters: selectable sim clock frequencies: 3.579 mhz 7.159 mhz 14.318 mhz sim supply voltage selection facility. sim reset and activation control. supported protocols and standards: gsm etsi 07.07 and etsi 07.05 at command support. iso/iec 7816 smart card communication support. sim communication command monitoring facility. hardware features: on-board sim card socket. led indication for: power status sim detection reset activity data transmission/r
Tender For purchase of lab equipments for ice dept - purchase of lab equipments for ice dept, i/p and p/i converter (iemcode:g002) i/p converter:(4 20) ma to (3 15) psi conversion. p/i converter:(3 15) psi to (4 20) ma conversion. air filter regulator (afr):20 psi regulated air supply. built-in current source. 3 digit led display for process indication. power supply: 230 v ac, 50 hz. mounting:bench-top / panel-mounted trainer configuration., level measurement using float and sight glass indicator- itemcode: g005specifications: sight glass level indicator. float type level indicator. power supply:230 v ac, 50 hz. monoblock pump:0.5 hp / 1 hp. sump tank., 8051develop ment board with usb/rs 232 cable to connect with computer (item code: g008)specifications: communication interface:usb / rs-232. on-board facilities:8 output leds,8 input switches,ldr,reed switch,8-bit adc,8-bit dac. display interfaces:seven-segment display,16 2 lcd interface. motor interfacing:stepper motor with driver,dc motor with h-bridge driver, 8 bit adc/dac interface board (item code: g009)specifications: thermistor / lm35 input in one channel. variable input (0 5) v in another channel. 8 leds for digital output indication.. necessary control signals provided for adc0809. 8-bit dac using dac0808. 8-bit digital input from controller. single-channel dac output:(0 10) v. power supply: 12 v or 15 v for analog circuitry, water level measurement trainer kit using capacitive type transducer (item code: g020) tabletop model with transparent acrylic tank of approximately 50 cm height. capacitive type level sensor for continuous level measurement. sensor output: (4 20) ma and/or (0 5) v with built-in signal conditioning. vertical pump for water circulation from sump to tank. flow control valve, overflow, and drainage arrangement. digital display for water level indication in cm. power supply: 230 v ac, 50 hz, single phase. in-built regulated dc power supply for sensor and control circuit. mounted on powder-coated ms frame for laboratory use. suitable for calibration and study of capacitive level measurement., flow measurement using electromagn etic flow meter(item code: g021)specifications: medium: water (salt water / bore well water). electromagnetic flow measurement: instantaneous flow rate and totalized flow indication. electromagnetic flow meter: integral mounted type. power supply: 90 260 v ac, 50 hz. minimum media conductivity: 15 s/cm. flow rate unit: m /hr. operating pressure: up to 10 kg/cm . electrode material: ss-304 / ss-316 / ss 316l. lining material: ptfe / neoprene / hard rubber / pfa. line size: 15 nb 25 nb. flow range: 0.1 10 m /hr. connection type: flanged. display: digital indication for flow rate and totalized flow. water pump: submersible type, 230 v ac, 50 hz. water tank: approximately 20 25 liters capacity. flow control valve provided. drain valve and overflow arrangement provided. mounted on powder-coated ms frame suitable for laboratory use.
Tender For supply & delivery of submersible pumpset with accessories connecting at anjaneyaswamy temple krishna nagar, 27th ward in madanapalli municipality- fabrication ,transportationand and supply of wall mounted control panelboard of size 600x600x250mm made of 18 swg crca sheet steel enclosure, 14 swg mounting plate for cable entry fabricated , painted with two coats of red oxide primer and two coats of grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using l&t / finolex copper frls cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets note: panelboard should contain 1) voltmeter ; 0-500 v 96x96mm size. -1 no 2) 0 to 20 amps / 0 50 amps ammeter (96x96mm size). 1no 3) single phase preventor of suitable range - 1no. 4)32 a tp, 10ka mcb. - 1no 5) indication lamps (r-y-b) with switch control - 1set 6)voltmeter & ammeter selector switch - 2 nos 7)supply and fixing of isi mark suitable capacitor ref: mat-03715 makes: l&t/bch 15 hp - 20 hp panelboard , labour charges for erection of three phase submersible pumpsets (bore well type) 15 hp pumpsets including pipe connection for suction and delivery and all labour charges etc., complete., (s.no: 11.3.17) , supply & fixing 50mm dia nominal bore gi pipe medium grade properties & weight as per is 1239 isi mark with gi fittings including the cost of pipe & its fittings & labour charges. jindhal/tata ref: bmw-f.89 , supply and delivery of 7/16 aluminum service wire as directed by engineer in charge ( as per quotation ) , supply and transportation of 15hp, 16-24 stage,5star rated submersible motor pumpset, confirming to is 8034 and motor confirming to is 9283 with waterproof winding, pump shall be suitable for various delivery head and discharge with stainless steel shaft. motor suitable for working on 415v ± 10%, three phase 50 hz ac supply etc complete for 6" bore well. makes: as per list of recommended brands as category i. makes: texmo / cri ref: mat03667 ( iteam code : m ) elec5.4.5 , supply of 3 core 4 sqm isi marked flat copper cable of isi for submersible motors confirming to is: 694:1990.makes: as per list of recommended brands as category i.makes:finolex ref: mat-02796 (elec1.6.3) , supply, delivery & fixing of 2" flange sets as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi bends as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi bits pipe as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi bore cap as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi coupling as directed by engineer in charge as per quotation , supplying & fixing gunmetal (gm) horizontal check (non return) valve as per is-778 i-class heavy duty - 50 mm nb size ref: mat-01856 ( bmw-f.39 )
Tender For supply & delivery of submersible pumpset with accessories connecting at reddys colony extension(near appartments) at ward no 32 in madanapalli municipality- fabrication ,transportationand and supply of wall mounted control panelboard of size 600x600x250mm made of 18 swg crca sheet steel enclosure, 14 swg mounting plate for cable entry fabricated , painted with two coats of red oxide primer and two coats of grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using l&t / finolex copper frls cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets note: panelboard should contain 1) voltmeter ; 0-500 v 96x96mm size. -1 no 2) 0 to 20 amps / 0 50 amps ammeter (96x96mm size). 1no 3) single phase preventor of suitable range - 1no. 4)32 a tp, 10ka mcb. - 1no 5) indication lamps (r-y-b) with switch control - 1set 6)voltmeter & ammeter selector switch - 2 nos 7)supply and fixing of isi mark suitable capacitor ref: mat-03715 makes: l&t/bch 15 hp - 20 hp panelboard , labour charges for erection of three phase submersible pumpsets (bore well type) 15 hp pumpsets including pipe connection for suction and delivery and all labour charges etc., complete., (s.no: 11.3.17) , supply & fixing 50mm dia nominal bore gi pipe medium grade properties & weight as per is 1239 isi mark with gi fittings including the cost of pipe & its fittings & labour charges. jindhal/tata ref: bmw-f.89 , supply and delivery of 7/16 aluminum service wire as directed by engineer in charge ( as per quotation ) , supply and transportation of 15hp, 16-24 stage,5star rated submersible motor pumpset, confirming to is 8034 and motor confirming to is 9283 with waterproof winding, pump shall be suitable for various delivery head and discharge with stainless steel shaft. motor suitable for working on 415v ± 10%, three phase 50 hz ac supply etc complete for 6" bore well. makes: as per list of recommended brands as category i. makes: texmo / cri ref: mat03667 ( iteam code : m ) elec5.4.5 , supply of 100a, 415v porcelain rewireable fuse units. makes: as per list of recommended brands.makes:c&s/standard/hpl/ sputnik / million / gold medal /gm/ benlo/anchor ref : mat02946 ( elec2.7.1 ) , supply of 3 core 4 sqm isi marked flat copper cable of isi for submersible motors confirming to is: 694:1990.makes: as per list of recommended brands as category i.makes:finolex ref: mat-02796 (elec1.6.3) , supply, delivery & fixing of 2" flange sets as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi bends as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi bits pipe as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi bore cap as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi coupling as directed by engineer in charge as per quotation , supplying & fixing gunmetal (gm) horizontal check (non return) valve as per is-778 i-class heavy duty - 50 mm nb size ref: mat-01856 ( bmw-f.39 )
Tender For supply & delivery of submersible pumpset with accessories connecting ramireddy layout 5th cross extension at 32nd ward in madanapalli municipality- fabrication ,transportationand and supply of wall mounted control panelboard of size 600x600x250mm made of 18 swg crca sheet steel enclosure, 14 swg mounting plate for cable entry fabricated , painted with two coats of red oxide primer and two coats of grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using l&t / finolex copper frls cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets note: panelboard should contain 1) voltmeter ; 0-500 v 96x96mm size. -1 no 2) 0 to 20 amps / 0 50 amps ammeter (96x96mm size). 1no 3) single phase preventor of suitable range - 1no. 4)32 a tp, 10ka mcb. - 1no 5) indication lamps (r-y-b) with switch control - 1set 6)voltmeter & ammeter selector switch - 2 nos 7)supply and fixing of isi mark suitable capacitor ref: mat-03715 makes: l&t/bch 15 hp - 20 hp panelboard , labour charges for erection of three phase submersible pumpsets (bore well type) 15 hp pumpsets including pipe connection for suction and delivery and all labour charges etc., complete., (s.no: 11.3.17) , supply & fixing 50mm dia nominal bore gi pipe medium grade properties & weight as per is 1239 isi mark with gi fittings including the cost of pipe & its fittings & labour charges. jindhal/tata ref: bmw-f.89 , supply and delivery of 7/16 aluminum service wire as directed by engineer in charge ( as per quotation ) , supply and transportation of 15hp, 16-24 stage,5star rated submersible motor pumpset, confirming to is 8034 and motor confirming to is 9283 with waterproof winding, pump shall be suitable for various delivery head and discharge with stainless steel shaft. motor suitable for working on 415v ± 10%, three phase 50 hz ac supply etc complete for 6" bore well. makes: as per list of recommended brands as category i. makes: texmo / cri ref: mat03667 ( iteam code : m ) elec5.4.5 , supply of 3 core 4 sqm isi marked flat copper cable of isi for submersible motors confirming to is: 694:1990.makes: as per list of recommended brands as category i.makes:finolex ref: mat-02796 (elec1.6.3) , supply, delivery & fixing of 2" flange sets as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi bends as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi bits pipe as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi bore cap as directed by engineer in charge as per quotation , supply, delivery & fixing of 2" gi coupling as directed by engineer in charge as per quotation , supplying & fixing gunmetal (gm) horizontal check (non return) valve as per is-778 i-class heavy duty - 50 mm nb size ref: mat-01856 ( bmw-f.39 )
Tender For purchase of equipments ( s.no 1 to s.no 5 ) for ece department - purchase of equipments, dso (digital storage oscilloscope) bandwidth: 50 100 mhz. sampling rate: 1 gs/s. channels: 2 (minimum). power supply: 100 240 v ac, 50 60 hz. automatic measurements: vpp, vavg, vrms, frequency, period, vmax, vmin, rise time, fall time, +width, width, +duty, duty, etc. horizontal scale: 5 ns/div 50 s/div or equivalent. vertical resolution: 8 bits (2 channelssimultaneously). vertical sensitivity: 1 mv/div 10 v/div (at input). waveform math: +, , , , invert, fft, etc. waveform storage: 16 waveforms or equivalent. communication interface: usb host and usb interface. display: 7-inch color display or equivalent. input impedance: 1 m 2% || 20 pf. accessories: 2 passive probes (1x/10x), 8051 micro controller kit operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., embedded trainer kit (using lpc 2148) cpu - lpc2148, core - 16/32 bit arm7tdmi-s speed - max 60 mhz, flash - 512kb, ram (on-chip) 40kb, 46 general purpose i/opins, usb2.0 one 10bit a/d converter with 14 analog inputs, one 10bit d/a converter, six pwm & watchdog two uarts (16c550), two i2c (400kb/s), two spi eight bit digital output, eight bit digital input,16x2 characters lcd and 4x4 matrixkeypad one potentiometer for giving analog input, relay& buzzer interface i2c devices: rtc, eeprom and seven segment display, on board stepper motordriver lm35 temperature sensor, one rs 232 lines are terminated at 9 pin d type connector and usb interface board has inbuilt power supply and mounted in sturdy cabinet accessories usb cable with utility software to download programs from pc to target board power cord, user manual, strain guage trainer kit ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual., sim reader trainer kitpower supply: operates on 230 v ac 10%, 50 hz mains supply. built-in regulated smps power supply. operating dc supply: 5 v / 12 v with overload and short-circuit protection. sim card interface: supports gsm sim cards compatible with 2g /3g / 4g / 5g networks. sim card read/write interface. supports sim card initialization, authentication,and communication functions. compatible with standard 6-pin / 8-pin sim cardsockets.communication interface: usb 2.0 interface for pc communication. rs-232 serial communication interface. uart communication facility for embeddedsystem interfacing. sim operating parameters: selectable sim clock frequencies: 3.579 mhz 7.159 mhz 14.318 mhz sim supply voltage selection facility. sim reset and activation control.supported protocols and standards: gsm etsi 07.07 and etsi 07.05 at commandsupport. iso/iec 7816 smart card communication support. sim communication command monitoring facility.hardware features: on-board sim card socket. led indication for: power status sim detection reset activity data transmission/reception built-in keypad for standalone operation. lcd display module (128 64) for menu andstatus display. on-board microcontroller-bas