Tender For development of street light by installation of 2 nos. of mini mast with fixture near borobagan kastodanga road(near montu tea shop) in ward no 127.
Tender For - arc of electrical material. - electrical work :, providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with uv stabilized pc (uv stablization report submitted for uv cover ) /toughened glass cover and secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm/ wt and potted driver & has a unique bis r number with input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driver efficiency >85% ,thd(i) 10% humidity 10% to 90% rh working temp -5c to 45c . driver current 750ma. the luminaire shall be bis certified and trade mark certified. life expectancy equal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs. manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate/ report with liable warranty of product/accessories from oem shall be submitted. all as per pre approved by engineer in-charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . led street light fixture with minimum lumen output 5600 lm, supplying and drawing of xlpe insulated lt aerial bunched aluminium conductor cable confirming to is 14255/1995 and is 398 (pt-4)/ 1994 and as per discom specs. on existing cross arms through i hook with all necessary t&p required including binding and twisting etc. complete in all respect as required. all as per pre approved by engineer in-charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 1 x 25 sq. mm. + 1x25 sq. mm. (insulated), supply and fixing of 11 kv pin insulator confirming to is:731:1971 with latest ammendment on existing bracket including all accessories like ms forged hot dipped gi pin confirming to is 2486(part-i)/1993 & is:2486 (part-ii)/1989 with latest amendment, and as per latest discom specs. etc. as required. all as per pre approved by engineer in-charge.for additional technical parameters of product / work refer annexure a attached with this bsr, sitc of ip-42 and general construction confirming to is:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and other parameters required as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:-(a)thickness of crca sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided(b)complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel. the panel having pe foam/ neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire.[c) interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only. all joints / interconnections of copper bus bar shall be dully tinned . c
Tender For corrigendum : supply of 350 w led fitting for hlms suitable for replacement of 2* 400 w hpsv fitting , 45w, 240vac, 50hz, ip66 led street light with internal driver, suitable for outdoor installation. powder , street light led fitting, 100w, ac, 240v, 50hz. ip66, suitable to mount on pipe, built with toughened , led flood light fixture (wp) 200w max
Tender For bid documents for providing, installing and testing of l.e.d street light fixture with tubular pole at various locations at santrampur nagarpalika dist: - mahisagar under sjmmsvy 2023-24 2nd attempt
Tender For supply of led lights and electrical items for switchyard kltps - store code: 7105327017 50w led flood light with aluminum body., store code: 7135020015 complete industrial led flood lighting with fixture 60 w ,230volt, 1-phase ,50hz., store code: 7150371655 100 watts led flood light fixture., store code: 7001080001 pvc tap roll, store code: 6903610029 pvc twin wire 2.5mm sqr., store code: 7105070014 led fitting 52 watt,24 v,ac operated ratiing, store code: 7840100016 smc junction box : dimension (outside-mm) 560 x 280 x 170, dimension (inside-mm) 515 x 240 x 145, make : sintex, store code: 7127090023 complete flame proof led light fixtures of 100 watt, store code: 6940510002 junction box, store code: 7135010670 helogen tube (lamp) 500 watt, store code: 4921020005 cable cutter taparia make size 24 prduct no.cc 24, store code: 7150160621 led street light fitting 60 watt
Tender For providing, installing, testing of l.e.d. street light fixture with pole as per various location chart, at- jasdan dist: rajkot under 15(percent) vivekadhin grant (year-2025-26)
Tender For supply of 50-watt led smd lighting fixture for flood light , street pole light led around 70 watt, ip66, with surge arrester , 100-watt led smd lighting fixture for flood light