Tender For corrigendum : supply of surgical d d -localizing organs on skin surface organs on skin surface after ct scan , bone cement with chlorophyll pigment , spine bone cement , vacuum mixing for bone cement , y connector for csf drainage kit , neurosurgical patties , raney clips flat shape , raney clip gun type applicator , suction irrigation device , suction tube disposable , suction tube key hole , aneurysm cliptray stainless steel , storagetray for clips and clip appliers incl lid stacking system sterilization , storagetray for yaneurysmclips stacking system made out of ppsu , storagetray for clips applier and instruments made out of ppsu for steam sterilization upto , clip remover for standard clip , clip standardtemp , applforcf minititanium clips bayonet rottitanjawdouble act , applforcf minititanium clips bayorigidtitanium jawdouble act , applying forceps for mini clips bayrotjaw angle double action , clip minitemporary slightly curved , applforc f std titanium clips bayonet rigidtitanium jaw up wards angeled , clip minitemporary , clip standardtemporaryangled , clip minitemporary curved angled closing force maxopening , applying forceps for mini clips rigid shaft rotating rigid ring handle , applying forceps for mini clips rigid shaft rotating rot ring handle , applying forceps for mini clips rigid shaft rotatingrot j ring handle , applforceps for standard clips rigid shaft rotatingrigid ring handle , applforceps for standard clips rigid shaftrotatingrigid ring handle , applforceps for standard clips rigid shaft rotrotjaws ring handle , appl forceps for standard clips rigid shaft rotating rot ja ring handle , applying forceps for mini clips forceps handle bayonet rigid jaw , clip standard perm. fen , clip standard permanent angled , clip standard perm template combined orbital floor plate, template orbital floor plate large, orbita floor plates, orbita floor plate right small, orbita floor plate right large, orbita floor plate left small, orbita floor plate left large, standard plates profile, hole straight plate, hole straight plate, hole l plate deg left, hole l plate deg right, t plate holes, hole double y plate, hole orbital plate, hole curved plate, burr hole cover plate, burr hole cover plate, burr hole cover plate, burr hole cover plate, orbital floor plate complex large, orbital floor plate complex large, orbital floor plate complex large, template combined orbital floor plate, dynamic mesh, dynamic mesh, dynamic mesh, dynamic mesh, dynamic mesh, dynamic mesh, dynamic mesh, dynamic mesh, titanium bone screws, titanium bone screws, titanium bone screws, titanium bone screws, titanium bone screws, emergency screws, titanium bone self drilling screws, titanium bone self drilling screws, titanium bone self drilling screws, titanium bone self drilling screws, titanium bone self drilling screws, drill bit, twist drill, twist drill, twist drill, mid face fixation implants, hole plate with bar, hole plate with bar, hole plate with bar, hole plate with bar, hole curved plate, hole curved plate, hole curved plate, tplate holes, yplateholes //bid details2 / 124
Tender For corrigendum : drilling of condenser tube plate(40mm tk) as per tube plate drg no-21601870029 rev-03, layout drg no-01600040068 rev 01 ,drg no-01601870029(ls-02 nos) and drg no01602370025(rs-02 nos). steam washable to be applied after drilling of tube plates.(note-
Tender For 25 kv earthing/discharge rod assembly for high rise ohe with working voltage 25 kv ac traction with top clamp (suitable for 36 to 50 mm bus bar and also suitable for 10 to 20 mm dia. conductor) . pole made of cast resin or resin-bonded glass fibre, coated with three coats of poly- urethane, the discharge /earthing pole assembly shall have an overall length of not less than 7.5 meters in five equal sections. single core flexible multi strand annealed copper cable should have double insulation, a cross section of 40 sq mm of size 248/0.45 mm and 14 meter long cable (specification is: 1554 (pt. i)- 1988 and is 2071 (pt. 1 and iii). with earthing double clamp drg. no. eti/ohe/sk/482 or latest (each discharge rod is to be supplied with 02 nos. earting clamps), insulated tee junction- insulated tee junction drg no. eti/ohe/sk/481 and re/33/p/530 or latest (the cable should have an insulated tee junction and the tee clamp should be of brass covered in clamp casing of ebonite material). and whole assembly to be supplied in rugged canvas bag and all shall be as per rdso specification no. eti/ohe/51 (9/87) with latest a and c slip no. 1 (10/92) or latest , and additional part required with each discharge rod to be supply. (1) 01 nos. insulated tee junction. (2) 01 nos. top clamp made of copper suitable for 36 to 50 mm bus bar and also suitable 10 -20 mm dia conductor, (3) 01 nos. spare earthing clamp and. (4) special instruction- 1. discharge rod cable lugs should be made of copper. 2. the cable should have double insulation, a cross- section of 40 sq mm, and 248/0.45 mm strands. 3. the discharge rod should be strong enough to prevent swaying or breaking during maximum extension. every nut and bolt used in the discharge rod must include a washer and spring washer to ensure secure fastening. 5. after the award of the p.o., the firm must ensure approval of one sample of the discharge rod from the consignee before rites inspection. 6. the length of cable from the earthing clamp to top clamp shall not be less than 12.5 mtr. in the cable an insulated tee junction shall be provided at a distance of about 3.5 mtr from the earthing clamp. from this insulated tee junction another piece of cable not less than 1.50 m long shall be provided at the end of which other earthing clamp shall be provided. 7. the galvanizedsteeltube (threaded) used for coupling of pieces of discharge rod should be at least 20 cm or more as required to prevent swaying of pole assembly during erection at site. also at every 5 cm apart two nos steel rivet is required to be provide on galvanizedsteeltube ( for preventing the galvanizedsteeltube from coming out from each discharge rod pole end). i.e. about 08 nos. or more steel rivet as required per galvanizedsteeltube is to be provided for proper fastening of galvanizedsteeltube inside the each pole of discharge rod. (warranty period- 30 months after the date of delivery). [ warranty period: 30 months after the date of delivery ]
Tender For sale and disposal of condemned items like ceiling fan, table fan, wall fan, exhaust fan, geyser, air curtain assorted, ac drive (vfd) assorted, auto transformer assorted size, pesto flash, voltage stabilizer, flood light, vfd/plc power capacitor, coil, condenser motor, tube light shed, chock assorted, old tv, relay of weighing scale, paneer ceiling machine, transformer, connector, connector switch, main switch, temperature indicator, pressure gauge, mcb, amature, search light, lamp, coil etc., grass cutting machine, hot case, split ac (01 no.) and window ac (02 no.), electronic weighing scale, copper scrap, aluminium scrap, brass scrap, ss scrap, magnet steel scrap, iron scrap including tin tupper, hindi / english news paper & magazine and raddi, battery assorted size, ball bearing, roller bearing assorted and bearing housing with and without bearing, steam vale, water valve, check valve etc. assorted size, lubricating pump, piston with ring, gear box, ammonia globe valve, butter fly valve, pully, empty plastic jar-40 ltr capacity, empty plastic bottles of vitamin a&d, crt monitor, cpu, ups, smps, keyboard, mouse, hp server ml 150, printer assorted size, fax machine (samsung) toner cartridge, ups battery 42 ah used ribbon of lipi printer, photostate machine, hp scanner, old phone instrument, motor assorted size 0.75 hp to 30 hp, water cooler, bod incubator, ac drive panel 40 hp, compressor assorted size, fridge (refrigerator), deep fridge, smp bags, with lining, used empty polythene pouch of milk / ghee, broken plastic crates, card board cartons / gutta, card board core used, wet mixed malba consisting polythene pouch, polylining, gutta, core, sutli etc., continues butter making machine panel etc as per details given in the following table below: