Tender For supply of 26vgwc001 - seal dowty , circlip , rivet , seat assy non split , indication lamp , indication lamp , indication lamp , indication lamp , indication lamp , indication lamp , indication lamp , indication lamp , relays , relays , relays , relays , oil seal , ferodo lining , ferodo lining , brake lining bearer , spring , band brake assembly with mounting pad & hinge pin , gearbox for band brake assembly with foundation & shaft , complete brake contactor , packing , o ring , seal packing , lug , winding temperature relay , 24 pin connector , return line filter , suction filter , circlip , o ring , o ring , dowty seal , o ring
Tender For supply of auxiliary gearbox balancing rod , balancing rod removing the gearbox and new balancing rod fitting , auxiliary gearbox repair and service , auxiliary gearbox mounting bracket , balancing rod , auxiliary gearbox mounting bush , popular shaft spider bearing , popular shaft universal joint old removing with lathe machine and new fitting , the gearbox removing and above all parts removing and new parts , auxiliary gearbox balancing assy , auxiliary gearbox mounting bracket , male female nuts and bolt , ramp assy repair service and testing , liner sleeve , head gasket hino engine , connecting rod bearing , valve inlet exhaust , valve guide , valve seal , piston ring , turbo charger repair and service with damaged rings and packing change , head gasket taken to the lathe machine shop and checking the head , rotary pump removing the veh and taken to the pump house and pump , the above mentioned all parts removing the engine parts fully cleaning , balancing rod broken change , water pump , the above mentioned removing and new parts fitting and veh
Tender For supply of auxiliary gearbox balancing rod , balancing rod removing the gearbox and new balancing rod fitting , auxiliary gearbox repair and service , auxiliary gearbox mounting bracket , balancing rod , auxiliary gearbox mounting bush , popular shaft spider bearing , popular shaft universal joint old removing with lathe machine and new fitting , the gearbox removing and above all parts removing and new parts , auxiliary gearbox balancing assy , auxiliary gearbox mounting bracket , male female nuts and bolt , ramp assy repair service and testing , liner sleeve , head gasket hino engine , connecting rod bearing , valve inlet exhaust , valve guide , valve seal , piston ring , turbo charger repair and service with damaged rings and packing change , head gasket taken to the lathe machine shop and checking the head , rotary pump removing the veh and taken to the pump house and pump , the above mentioned all parts removing the engine parts fully cleaning , balancing rod broken change , water pump , the above mentioned removing and new parts fitting and veh
Tender For procurement of bottom ash and wet ash spares for overhauling of unit 3 under ahp mm - nozzle for air washer (dry for fly ash system size: 5 mm dia,for ahp-ii, nozzle with insert # tip dia 9 mm of insert,moc-ss 410 (nozzle),ceramic,hardness 7708 mohs,ahp-i# for 10in wetting head,make-dcips,pn-6,7, inlet section fr wetting head10" of ahpi ( one side bevelled and others side plain (b/p),after 90 degree 10" elbow for wetting head. moc: durite 450bhn ), adaptor for collector tank ( one side bevelled and others side flanged with holes. mat: durite 450bhn ), adapter b/b # for ahp-i,below wetting head# for collection tank ( both sides bevelled. mat: durite 450bhn ), tail piece after combining tube,ahp-ifor ba slurry line,make-dcips ( one side bevelled and others side plain (b/p),after combining tube. moc: durite 550bhn ), complete assembly of jet pulsion p/p moc: durite 550 bhn for body,ss-410 for nozzle tip,ceramic 7 moh min for nozzle insert,cap.-60 t/h,pr.-10 kg/cm2 for ahp-i, combining tube # dcips make-dcips,part no.-1,moc: durite,550 bhn,for ahp-i ( hydrostatic test pressure at shop: 9 kg per sq cm (g). ), drain pit jet pump,ejector type # complete assy with water inlet elbow,pipe with flange,bolts and nuts and foundation bolts ( discharge rate of 35 # 50 cubic mtrs. / hour, horizontal distance of 150 # 160 mtrs with an elevation of 10 mtrs from gound level (0.00 mtrs), sump volume : 45 cubic mtrs. one no. orifice for discharge line with each of ejector jet pump is required with other accessories. ), ba hopper,feed sump/chute for bottom ash hopper, nozzle # of seal trough,for ba hopper,ahp-i# for ba hopper,ahp-i ( nozzle with holder. ), inspection window assembly looking glass dia 224 mm th 12 mm for ahp-ifor ba hopper, inspection window glass,200m # ( moc: borosilicate glass. ), shaft sleeve for clinker grinder for make-ucc/dcips,pno. 15 moc ss 410, 350 bhn, for ahp-i, cambolt,nut,locknut # moc-ss 410(cambolt) heat treated to rc 32-34,metric m 20 coarse a2-70,is 1363 (nut# for ba clinker grinder ( 1set=32 nos 1. moc: ss-420 (cam bolt) heat treated to rc 32-34. metric m20 coarse a2-70, is 1363 (nut). 2. 01 set: ), packing gland follower # moc: bronze ltb-2 is 318,for ahp-1 ( for ba excen crusher 1. part no.-12 2. moc: bronze, ltb:2 is:318 ), labyrinth ring of bearing housing moc-ms is 2062,for ahp-ifor clinker grinder,make-dcips ( for ba excen crusher 1. part no.-13 2. moc: ms is 2062 gr-a. ), chain # no of link-118,for ahp-i ( for clinker grinder of ahp-i. no of link: 118. ), small size sprocket for ahp-1 bktpp for gearbox,for ahp-i, packing gland housing # moc: ci fg 220 is: 210,for ahp-i ( for ba excen crusher 1. part no.-9 2. moc: ci fg 220 is: 210. ), slinger for bottom ash crusher dcips moc-ms,is:2062 gr-a,drawing no 25p06-t-1b-582 ( for ba excen crusher 1. part no.-14 2. moc: ms is 2062 gr-a. ), cam for clinker grinder # heat treated & normalised for ahp-i# for moc:hi chrome alloy with 22% to 27% cr, gate face of feed gate # moc-ss 316 for ahp-i ( moc: ss - 316. including m12x65, csk hd soc. cap bolt, nut, washer. ), adjustable seating wedge # moc-ms,is:2062 gr-a for-ahp-i ( for feed gate. moc: ms, is: 2062 gr a. ), roller # moc-steel.is:1030 for-ahp-i ( for feed gate of ba crusher. moc: steel, is: 1030. ), gland follower for indicator rod dcips of feed gate, ahp-i, guide angle l.h # moc-ms,is:2062 gr-a for-ahp-i ( for feed gate ), guide angle r.h # moc-ms,is:2062 gr-a for-ahp-i ( for feed gate ), indicator rod # moc-s.s,size: 21mm dia.(solid) and 1400 mm long with both ends threaded and nuts,stg-i# for bottom ash hopper feed gate