Tender For mtps i tm unit i overhauling of beacon rotork ind modact actuator with renewal of oil seals o rings wheel retainer ring replacing the defective worm wheel limit switch drive shaft checking the mechanism and oil filling during unit i aoh 2026 27
Tender For tender for supply of fabrication - hex nut m39 3 as per drg 46130002460 s00 r00 with matl as per spec aa10208 rev 07 , thrust brg clamp upper as per drg. 36187000943/02 with matl as per specn. aa10119/15 , drive adjustment block (without item no. 2 of drg) as per drg. 36188090123/00 (var-01) with matl as per specn. aa10119/15 , drive adjustment block (without item no. 2 of drg) as per drg. 36188090123/00 (var-02) with matl as per specn. aa10119/15 , lower support plate (bm-009.63) as per drg. 36187000950/01 with material as per specn. aa10122/15 , skate roller and frame assly as per drg. 26187001159/03 with material as per drawing , coupling guard as per drg 26187001133 01 with matl as per specn is 1079 , hex screw m39 3 140 var 02 hy 705 22 fully m cd item as per drg 46118000943 01 with matl as per specn aa10208 07 , lock nut hex m48x3 as per drg. 46187090156/00 with matl as per specn. aa10208/07 , stud m39x3 1200l as per drg. 36187000949/01 with matl. as per specn. aa10305/08 , jr. stop bolt hy 257 02 fully m/cd item as per drg 36137000839 03 with matl as per specn hy-10664 06 or en 19 u , pin as per drg. 46188000948/01 with matl as per specn. hy10561/04 , output shaft stud as per drg 36187000945 03 with material as per specn hy10664 06 or en 19 u , hex nut m39 3 as per drg bm std 032 rev 00 with material as per specn hy10664 06 or en 19 u , scrapper pin (hy-251.03) as per drg. 36117000898/06 with matl as per specn. hy10664/06 , thrust brg clamp lower as per drg. 36187000942/02 with matl as per specn. aa10119/15 , upper support plate as per drg. 36187000948/01 with material as per specn. aa10122/15 , output shaft skirt assly (hy-705.26)fully m/cd item as per drg. 36118003145/00 with matl as per drg. , tie up of track plate as per drg 46118000883 rev 01 with material as per spec aa10119/15 , skate retainer plate as per drg 46118000887 rev 01 with material as per spec aa10119/15 , locknut wrench as per drg 36187000928 rev 00 with material as per spec aa10119/15 , puller spacer pillow block as per drg 36187000947 rev 00 with material as per drg , mounting block lh as per drg 46188000986 rev 00 with material as per spec aa10119/15 , puller angle plate pillow block as per drg 46188000987 rev 00 with material as per spec aa10119/15 , wrench trunnion shaft end caps as per drg 36188000998 rev 01 with material as per spec aa10119 , mounting bracket-rh as per drg 36188001000 rev 00 with material as per spec aa10119/15 , mounting bracket - lh as per drg 36188001002 rev 00 with material as per spec aa10119/15 , mouting block-rh as per drg 46188001010 rev 00 with material as per spec aa10119/15 , tilt out plate as per drg 46188001013 rev 00 with material as per spec aa10119/15 , spring preload fixture as per drg 26187001185 rev 00 with material as per drg , grinding roll wear meas. gauge as per drg 26188001221 rev 00 with material as per drg , preloading adjusting stud as per drg 36187000929 rev 00 with material as per spec hy10664/06 , high strength stud as per drg 46187000951 rev 00 with material as per spec hy10565/03 , bowl extension ring hoisting clevis (var-01) as per drg. 26188001135/01 with matl as per specn. aa10119/15 , rail connector (rh) as per drg. 46118000885/00 with matl as per specn. aa10108/11 , rail connector (lh) as per drg. 46118000886/00 with matl as per specn. aa10108/10 , channel frame assy as per drg. 16187000532/00 with material aa10119/15 for plates and aa10108/10 for section , bowl hoisting frame hook (var-01) as per drg. 26188001157/00 with matl as per specn. aa10119/15 , rail connector plate as per drg. 46187002214/00 with matl as per specn. aa10119/15 , stud with nut m10 as per drg. 36187000944/01 with matl. as per specn. hy10199 or aa10208/07