Latest heat transfer machine Tenders | Government heat transfer machine Tenders

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

CTN :45704269

17 Jul, 2026 NA

Tuticorin - Tamil Nadu

Tender For providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - industry unit; acoustic eye inspection followed by 10% boroscopy of hp heater tubes; as per tender document

CTN :45703815

11 Jul, 2026 6.00 Lacs

Kheri - Uttar Pradesh

Tender For supply of general electric items b b - wire 22swg , glass sleev 14 mm , slip ring for cane unloader bbl make 10 kw motor , exhaust fan 24 , plastic cooling fan for 5 00 hp motor , plastic cooling fan for 7 5 hp motor , plastic cooling fan for 10 hp motor , havells make auto cut hot air blower 2000 watt with overheat protection , soldering iron 65 watt , soldring wire , plastic cooling fan for 50 hp motor , teflon rod dia 65mm length 300mm , glass sleev 16 mm , mash rum type push button red , mash rum type push button blue , plastic cooling fan for 15 hp motor , carbon brush 12 20 32 , mettalic carbon brush 20 15 8 , carbon brush 30 20 100 , timer st 800 , carbon brush 21 31 37 , porcelean kit kat200 amp 415 v standard make , fuse wire 6 amp , fuse wire 10 amp , fuse wire 16 amp , dol starter empty box mk1 , dol starter empty box ml2 , exhaust fan 16 1 phase 960rpm ci body crompton havells make , carbon brush 20 32 40 , rocker arm 12 5 hp kec slip ring motor , h t connector 3 way , h t connector 6 way , potentio meter 500 ohm 2 w 10 turn bourns make , diode 6 amp , step down double phase transformer 415 vac to 24vdc , usha bajaj make room heater with ss reflector and body , dc solenoid coil for hydraulic grab for reverse forward direction , ss seamless ring size 1 for cane unloader , karam make industrial safety belt , silk rope 3 4 resham , foldable aluminium ladder 16 ft , amp meter 400 5 96 96 , amp meter 0 100 5 96 96 , amp meter 150 5 96 96 , limit switch 1 no 1 nc type ls 011 10 amp 500 v , frequency meter 96 96 , frequency meter digital type , air cooled resistance box for 12 5 hp 15 hp bbl make slipring motor , analog rpm meter make beacon sensor type input magnetic picup no of teeth 06 range 0 8000 rpm , selector switch for volt meter , selector switch for amp meter , volt meter 96 96 0 500 vac ae make , current transformer ct 250 5a , amp meter 300 5 96 96 , amp meter 600 5 96 96 , dyno pack with controller , current transformer ct 300 5a , current transformer ct 400 5a , current transformer ct 600 5a , current transformer ct 500 5a , current transformer ct 100 5a , carbon holder for 12 5 hp slip ring motor cane unloader motor , current transformer ct 500 1 a , amp meter 500 5 96 96 , amp meter 800 5 96 96 , porcelean kit kat 100 amp 415v , amp meter 250 5 96 96 , amp meter 1200 5 96 96 , timer 800 q 1 no 1 nc , portable single phase welding machine 220 vac , current transformer 1200 1 , current transformer 1200 5 , ictpn switch 200 amp , metravi make nctm 200 contact on contact combined digital tacho metermeter , diamond hammer drill bit size 6 mm for aluminium busbar drilling , diamond hammer drill bit size 8 mm for aluminium busbar drilling , diamond hammer drill bit size 10 mm for aluminium busbar drilling , diamond hammer drill bit size-14 mm for aluminium busbar drilling

CTN :45680117

09 Jul, 2026 NA

Tiruvallur - Tamil Nadu

Tender For c26m26r022 - 2951034018 - 90-e-501 hp steam super heater assembly as per cpcl specification no

Central Government/Public Sector

CTN :45702761

03 Jul, 2026 NA

Multi City - Tamil Nadu

Tender For auction sale of depot ferrous scrap - cond.& u/s diesel/emu/c&w/lhb, equilising beam, buffer, ac loco components such as tooth gears, crank shaft, brake disc, pinion, injector, gear wheel, cylinder liners, grease cup, alternator fan cover filter assembly, cattle guard, sab air brake components,air brake cylinder components, shock absorber, cattle guard, linear,traction motor spare parts, dust collector,tapperbearing with polimer cage,doubelcupcollar,shockabsorber,hp cylinder rail guard, outer/inner sleeves of bearing bolts& nuts, air filter, damper, lube oil filter, tiny springs,rotor, anchor link scrap, sab components, cutoff angle cock, control arm upper, ca lower, traction rod, anti roll bar assembly, axle box components, gears, brake disk, leaf spring, carrier assembly, bearing bolt, centering device, fork eye, coupler sleeve, air pipe assembly, break shoe bolster link, hoop coupler, parking break assembly,primary and secondary springs,footsteps,bolster hanger, dust guard, wearing plate, compensating ring, impeller, inner hanger,iron bracket above transformer, brake gear components, spring plate, coupler sleeve, brake hanger, yoke lead, coupler bearing, coupler rear plate, coupler clearance plates, wearing plate, brake beam, dust covers, collar, dashpot top, protective tube, gear case vocer, side bearer cover, pins for hanger, machinery items cut pieces, shock absorber, nipplers, cutout cocks, etc., tm pinion, tm parts as holder plate and end shield, axle box parts as axle box cover,boldter,oilcup,angles,equilising stay,pipes,nosepad,lsbeam,cibrakeblock , automobile parts,silentblock,impeller housing,cowl, axle guide and racer, traction link, the bar, traction housing,brake hangar, pull rod, slack adjuster, knuckle, clevis, screw coupling, cbc coupler and parts, fuffer, cattle guard, labyrinth, bearing for axle box, traction motor and aux motors, damper, sand box, sand ejector, sand pipe, foot step, sand ejector., angle cock and ferrous couplings, lathe machine head, junction box, cutting ferrous, angles, rod, ferrous heater coils, ferrous lamp pipe, transformet brackets, oil lubricator for suspension bearing, lid for gear case, linear, push rod &gudgeon pin, compressor, hood with impeller,ocb ducts, labyrinth, end frame tamper, hanger link, cylinder linear, oil dispersive, axle box cover, servo motor, striker casting with grease adherings(diesel),castiron components, impeller, guard, compartment sliding doors, compensating ring, end sheild, cartridge with nu bearing,pipe, drum,hoist, gear, impeller, eot crane wheels, eot crane gears , side rod, pull rod, pinion wheel, pull lift chain, door closer, emu coupler,inter cooler, engine head, covers, dooms, pipes, tank, front cover, rear cover, hand rail, after cooler, cylinder body, spring piston, holder plate,sand box, labyrinth, lhb bearings, outer bearing covers, end shield, piston trunk, adjusting rod, palm pull rod, control arm, dbr rf boxes,hoods, brake hanger, brake hanger with head, brake head & semi permanent coupler and parts, bmbc components, bend cover, inspection cover, centrifugal dust collector, cut off angle cock, safety rod, racker arm, valve plate, cylinder bore, bearing cover, emu sliding door, silencer, racer, raiser, bellow plate, door operating cylinder scrap, msu components scrap, labyrinth &pinion shaft(diesel), compensation ring, buff gear, hood with impeller, ront fork complete housing, lb spring set scrap, stator w/o coil, contering dis, anger link with or w/o silent block, oil cup and all other scraps released from diesel / ac loco/emu/c&w/lhb components and all other ms/ci with/without minor non ferrous attachments in as is where is condition. pl no. 98050126. custodian: cdms-rsf-gsd-per. note: 1) cutting permitted to loadable sizes only. 2) during delivery if any major non-ferrous items found the same should be handed over to custodian. 3) loading by crane / jcb is also permitted. location: bin n

Central Government / Public Sector

CTN :45469612

30 Jun, 2026 NA

Begusarai - Bihar

Tender For corrigendum : supply of m7901800001motor 1ph550wp3m01h12002 , m7901800002 idu pcb including sensor vdsu03a1 , m7901800003 wired remocon pcb with cable vdsu06b1 , m7901800004 blower assy right syz 10101 , m7901800005 expansion valve aae 8 hc odf ee 5ft 58x , m7901800006 g i air filter ac158034003nn , m7901800007 filter drier dcl165023z501058f , m7901800008 voltage monitor lp delay 20 sec mkm , m7901800009 05 hp 370w 900 rpm picl motor uh11139 , m7901800010 crank case heater dia 170hlm072 , m7901800011 fan4 lobe 24 in metallic cruise , m7901800012 118 brazed tube with service valve , m7901800013 58 brazed tube brass service value , m7901800014 mw fl ac hp switch yk01h 000450p350r , m7901800015 mw fl lp switch yk011 000035g050g , m7901800016 schrader valve 14 fi 18 npt brass , m7901800017 compressor yh266t110085 tr r407c

Central Government/Public Sector

CTN :45653875

03 Jul, 2026 NA

Medak-T - Telangana

Tender For fabrication of hp heater skirt and shroud assembly and dsh skirt assembly with heat treatment (sr)

corporations/Associations/Others

CTN :45345600

01 Jul, 2026 14.56 Lacs

Sonbhadra - Uttar Pradesh

Tender For corrigendum : supply of oh of main steam line valve v2 6 , oh of steam by pass valve v2 27,15, and v2 7 , oh of es 3,4,5,6 and 7 , oh of v2 -82-84 and v2-81-a to 81c , oh of hd-21, hd-29, hd-30 and hd-31 , oh of nrv of h.p. heater and feed pump , oh of group protection valve of hph , oh of dw-4, 37,38,39,40,41 and ca 5 , oh of cst makeup valve v6 60 , oh of as-48 valve , oh of nrv of extraction line es-8 , oh of suction valve of bfp , oh condensate wtr throw off valve to condenser , oh throw off valve to cond and steam isolating of lph2 , oh of steam isolating valve of lph 3, 4 , oh of safety valve of aux prds or deaerator , oh of safety valve of h.p. heater , oh of safety valve of l.p. heater. , oh of safety valve of cbd tank. , oh of safety valve of flange or stud heatng , oh of safety valve of warm up line. , overhauling of actutator of as 48 valve , oh of actr feed line valvev2 81 or v2 82 or v2 83 or v2 84 , oh of actr of v2 7 or v2 15 or v2 27 , oh of actr drip line valve and ext line valve , oh of actr valve connected to condenser , oh of actr cst make valve , oh of actr of msv l and r , oh of actr of steam isolating valve to lph2 to 4 , oh of actr steam throw off valve to condenser , cut or weld or repl of hp valve 15 to 50mm , cut or weld or repl of hp valve 51 to 100mm , cut or weld or repl of h p valve 101 to 150mm , oh of butterfly valve of condenser , oh of dea and fst with internal painting , repair or replacement of broken hanger , tightening of loose hangers , cut or weld or repl of l.p. valve 15 to 50mm , cut or weld or repl of l.p. valve 51 to 100mm , cut or weld or joint of h.p. pipe 15 to 50mm , cut or weld or joint of h.p. pipe 51 to 100mm , cut or weld or joint of h.p. pipe 101 to 150mm , cut or weld or joint of h.p. pipe 151 to 300mm , lift or straight aprds hdr by cutting weldding , o h of lph 1a , 1b , o h of lph 2 3 and 4 , oh and attend flange leakage of gc i or ii , clean of turbine oil or h2 gas cooler str , repl of damaged sp. valve v2 38 , repl of damaged special valve v2 27 , oh of turbine oil coolers , oh of main ejectors of turbine , oh of h.p. heater , oh of lcv 3to15pcv-5, 14,16,17,tcv 8 , repl bend of lp drip connected to drip pump or condenser , cut damaged bend of hph drip cont to dea , cut weld or repl of h.p. valve 151 to 300mm , blank of crh line for ht and normalizing , oh of h.p. valve nrv in h.p. line , oh of l.p. valve nrv , oh of energy absorber of bfp , oh of dss of aux. prds. , 2coat paint bcw,clr,bfp,cep,drip pump and line , 2coat paint cst,bcw pump ,swc tank,line,valve , 2coat paint hcplg,sw,bcw,cw exc clr line , 2coat paint air washer sys,cep or phos orhyd , 2coat spray paint syn super enamel lpc , 2coat spray paint front ped,barring gear , 2coat spray paint brg and housing turbine , 2coat spray paint cntl valve casing , 2coat spray paint condenser and line , 2coat spray paint main oil tank , 2coat spray paint main ejector , 2coat spray paint centrifuging machine , 2coat spray paint lube oil cooler , letter writing 2 inch size dia

CTN :45675374

09 Jul, 2026 NA

Multi City - Bihar

Tender For auction sale of others - 1 control terminal block 16 mm 03 nos. 2 hp/lp cut out 05 nos. 3 scrap scroll compressor 10 nos. 4 scrap blower motor, 1.5 hp, 1400 rpm with top 18 nos. 5 scrap condenser fan motor, 1 hp, 1400 rpm with top 18 nos. 6 ss welded round guard 03 nos. 7 dryer filter (1.5¿ solder type) 29 nos. 8 hartige ( coupler) connector 24 pin 46 nos. 9 hartige ( coupler) connector 16 pin 20 nos. 10 dumper actuator 5 nos. 11 male female plug and socket for dumper actuator 5 nos. 12 pressure transmitter ( 0-10 bar) 20 nos. 13 pressure transmitter ( 0-40 bar) 26 nos. 14 glass bulb cartridge 130 degree 59 nos. 15 scrap esti switch assembly with cartridge 9 nos. 16 air heater set consisting 400 watt ( 15 nos.) coil with insulated backelite sheet 3 nos. 17 scrap low pressure control switch (auto reset) 38 nos. 18 scrap high pressure control switch (auto reset) 50 nos. 19 scrap control pressure switch (auto reset) 24 nos. 20 expansion valve 22 nos. 21 hp gauge (0-40 bar) 13 no. 22 lp gauge (0-10 bar) 13 no. 23 set point generator switch 5 nos. 24 top cover (part-i inside) 4 nos. 25 hygrostat 35-100% 8 nos. 26 scrap compressor contactor -type ls-1 bk 00 dc 110 volt 44 nos. 27 scrap condenser motor contactor -type 1.54k10e dc 110 volt 37 nos. 28 scrap blower motor contactor -type 1.54k10b dc 110 volt 27 nos. 29 dc-dc converter for flapper motor, 110 v/24 v , 1.5 amp 3 nos. 30 bottom cover (part-i inside) 4 nos. 31 electronic controller (srmc-20) 5 nos. 32 top cover (part-ii inside) 4 nos. 33 multifunctional monitoring relay, 750 volt 33 nos. 34 scrap dc-dc converter , 110 v/24 v, 20 amp/1.5 amp 20 nos. 35 return filter, fresh air cassette filter 73 nos. 36 scrap bush bearing clutch plate, commutator, carbon brush holder including carbon 4 nos. 37 bottom cover (part-ii outside) 4 nos. 38 b-check kit for dg 14 set 39 solenoid switch of self-starter 2 nos. total ferrous - 958 kg total copper - 71 kg

CTN :45421068

26 Jun, 2026 NA

Leh - Jammu And Kashmir

Tender For bid to ras tender for supply of mt spares - lv7/t-815 , 443-115-187-824 , water proof starter motor 5.8 kw/24v , lv7/t-815 , 150-200-004-004 , hydraulic cylinder hm 50/25/400-111.111 , lv7/t-815 , 442-070-850-334 , oil filter , lv7/t-815 , 443-224-862-914 , heater glow plug two-pole , lv7/t-815 , 443-853-040-053 , flasher change over switch , lv7/t-815 , 150-180-006-002 , fuel filter assy , lv7/t-815 , 452-335-871-506 , becon orange 8563.5/201-24v , lv7/t-815 , 443-321-011-000 , air pressure guage c303582 , lv7/t-815 , 443-815-432-020 , circuit breaker 9432 020 , lv7/t-815 , 443-317-056-109 , signal lamp , lv7/t-815 , 627-962-310-521 , filtering insert( 05-023-000) , lv7/t-815 , 347-451-433-314 , bulb 24v 70w h3 pk 22s , lv7/t-815 , 990-115-011-000 , brush set -19024644 , lv7/t-815 , 121-223-352-240 , bulb 24 v/21 w ba 15s , lv7/t-815 , 443-962-500-044 , dust cap , lv7/t-815 , 413-411-018-001 , combination pliers 180 csn 23 0380 , lv7/t-815 , 101-111-014-284 , seal plain (101 111 014 284) , lv7/t-815(4x4) , 130-999-511-000 , clutch plate 430 gtz 4918 62521 , lv7/t-815(hmv) , 482-hp-11716 , chain pulley block (0.5t capacity) , lv7/tata , 4031635 , turbocharger

Heat Transfer Machine Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government / Public Sector

Central Government/Public Sector

corporations/Associations/Others