Tender For supply of low speed fan motor assy with connector c c -low speed fan motor assy with connector , assy release bearing 1 75 dia , cover timing belt outside , hose water outlet , seal ring metal , protector bumper corner rh , protector corner , relay assy , repair kit mechanical transmission , parts kit slave cylinder clutch , seal kit steering gear box , drain luge ring , drain tank packing , mirror assy out rear view rh
Tender For corrigendum : providing of repair and overhauling service - erdd of icgs c-154 for replacement of mechanical seal stbd asd system; 2000000; no; buyer premises
Tender For providing of repair and overhauling service - repair of hst; repair of hst; no; buyer premises - di as per csdo schedule and general cleaning. check and clean dust collector check and reset v belt tension. change the v belt if worn out. change external seal kit-2t & 4t. check mechanical structure and parts for damage repair/eplace if required. check rubber sleeves and hose pipes for damage. change if equired check for noise, vibration etc. while operation and while owing full hydraulic system check for leakage, clogging of filters, and pump function close loop operation to be done to remove dirt particles in the ystem 10. check pneumatic parts and pipe lines for damage and leakage. carry out rectification/replacement. 1. check all gauges for proper functioning. carry out repair/ceplacement if required. 2. check the condition of battery. 3. check the cable connections at starter, alternator and battery for their tightness. 4. check function of all switches and indicators. carry out rectification/replacement if required. 5. check all bulbs, tube lights and led indicators for damage/unserviceable. carry out rectification/replacement, if required. 6. run the trolley for 2 hours continuously and check all function and leakage of the trolley. 7. general checks: tyres, wheel bolts, glass, door locks, breasing, fire extinguisher, exhaust smoke condition, engine parameters, leakage, etc 8 warranty 03 months
Tender For corrigendum : tender for supply of cartridge for ga 101a b , comprn unit a.d.e.f drg no pr 10328d , ring 0 for shaft packing , ring o mating ring , ring carbon seal face , ring mating seal face , ring pumping 8 , ring o part no 11 , ring o part no 17 , oring 5 ga101 pump , seal mech 503.5 503.5 , sleeve for primay shaft , sleeve for second.shaft , set of o rings sealol , set of o ring , throttle bush p.no.6 , seal mech complete k203 , compression unit for 1004 , ring seal stationary , seal mech for lop gb 101 , assly seal primary p 301 , ring mating p.no.2 21 22 , ring o c 3 6 m 9 12 20 , sleeve p.no.11 p 301 , collar drive p.no.13 p301 , ring mating p.no.8 p301 , ring seal p.no.l p301 , cartridge for mech.seal , set of springs d or p , cup sec. seal k n , ring seal b p301 , gland 10 for p301 seal , m.r.carrier for p301 seal , cartridge mech seal p307 , seal ring p.no. a p 307 , circlip p.no. b p 307 , o ring p.no. c sealol , thrust washer d sealol , mating ring tc p 307 , o ring for tc sealol , o ring set p.no.6 5 9 16 , sleeve upper p.no.8 p 307 , sleeve lower p.no.15 p307 , lock nut de p.no.17 p307 , lock nut nde p.no.22 p307 , drive collar p.no. 10 , clamp collar p.no.19 , set of springs 16 p.no.e , cup for carbon face pno.f , half dog screw p.no. 11 , compunit b d e f g h p307 , sliding washer 12 p 307 , set of o ring mech seal , comressor unit primary , seal mech despatch pump , seal ring primary k , wedge and follower d and e , mating ring primary 7 , o ring 3 , compresion unit secondary , seal ring second b , wedge and follower sec d and e , mating ring second 2 , o ring 8 , sleeve shaft 17 , ring o for pump p3301 a b c d , o ring part no 18 , o ring 19 , mating ring carrier 4 , pumping ring 9 , assly seal mech 560 028mm , ring seal pump 51a p 521 , repair kit o ring 936 , ring mating tc 3 p521 , seal mech.for p 521 a b , sleeve for shaft 50 , throttle bush 4 p 521a b , assy mech seal complete , bush mechanical seal. 12 , ring o mech seal , ring o mech seal , ring o for shaft sleeve drg egl080 r2 11 , ring o seal collar drg 080 r2 19 , ring seal composite 3 with o ring 4 , collar p.no.13 for p601 , seat floating 2 , shaft sleeve 152x123 42 , ass.mech.seal , bush mechanical seal , ring o mech seal hp bfw pump p 605 a , sleeve and ring mech seal hp bfw p 605abc , ring o shaft sleeve drg egl079 bfw p 605 , ring o seal collar 19 drg egl 079 , ring seal composite drg no egl 079 , collar p.no.13 for p605 , sleeve shaft 12 , seat floating 2 , ring seal part a , ring mating part 2 , seal mech for tx 301 , set of o rings for m seal , sleeve for mech seal for tx 301 , set of springs part no f , tx 301 mating ring carrier p n. 6 , tx 301 o ring p n. 7
Tender For providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - onboard ins jalashwa; renewal of mechanical seal of 2b main feed pump as per scope of work; service provider
Tender For providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - icgs c-428; e013 fuel leakage was observed from fuel pump weep hole of stbd da suspect mechanical seal of fuel pump worn out defect to be rectified and proved for satisf..