Tender For sic of submersible pump set and all allied e/m equipment for rebored tube well near h.no.-116c shahpur jat in greater kailash constituency ac-50. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 10 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point:200 lpm on 90 mtr. head. having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved make, supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted.a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no.b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 noc) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no.e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable bankingg) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos. complete wiring & installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated & pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs.make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., s/o nut & bolts of 1/2 dia of different size i.e. 1.5 dia& 2.5 long full threaded., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 8-10 inch diameter made out from 6mm thick m.s. sheet in 2 halves & a circular hole in centre 3-1/2 dia. with locking arrangement by nuts & bolt., earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.
Tender For tender for rate contract of orthopedic trauma implants - arthroplasty implants, proximal humerus locking compression plate (philos) 3.5mm, left/right set: 3 to 11 holes on shaft of plate with 9 locking screws 3.5mm (length-all sizes) and 6 cortical screws 3.5mm (length-all sizes), stainless steel., narrow 4.5 mm locking compression plates set: 6 to 14 holes (combihole design) with 4 cortical screws 4.5mm (length- all sizes) and 6 locking screws 4.5mm (length- all sizes), stainless steel., distal humerus anatomical locking plate set 3.5mm left/right (two plates- one medial and one lateral with 6 cortical screws and 8 locking screws, 4 to 8 holes on shaft of plate), stainless steel., extra articular distal humerus locking compression plate 3.5mm left/right set, with 4 to 12 holes on shaft of plate(combihole design), with 4 cortical screw(length- all sizes) and 8 locking screws (length all sizes), stainless steel., interlocking nails for humerus with provision for minimum 3 proximal and 2 distal locking screws (nail diameter 6-8mm, length 22-30mm), proximal radius anatomical locking plate set 2.4mm/2.7 mm, left/right for fixation of radial head and neck, 4 to 6 hole with 4 locking screws and 2 cortical screws, stainless steel., olecranon anatomical locking plate set (hook plate) 3.5mm, left/right, 4 to 8 holes on shaft of plate with 8 locking screws and 4 cortical screws, stainless steel., locking compression plate 3.5mm (combi-hole design) set 5 to 12 hole with 4 cortical screws and 4 locking screws, stainless steel., 1/3rd tubular plate set 3.5mm 4 to 12 hole with 8 cortical screws, stainless steel., 1/3rd tubular locking plate set 3.5mm 4 to 12 hole with 4 cortical and 6 locking screws, stainless steel., distal radius anatomical locking plate set (volar) 2.4mm/3.5mm left/right with 3 to 7 holes on shaft of plate, with 6 locking 2.4mm screws and 2 cortical 3.5mm screws and 4 locking 3.5mm screws, stainless steel., distal radius t locking plate 3.5mm set with 3 to 7 holes on shaft of plate with 6 locking screw and 4 cortical screws, stainless steel., distal radius t non locking plate set 3.5mm set with 3 to 7 hole on shaft of plate with 8 cortical screws, stainless steel., clavicle locking plate set 3.5mm right/left (6-8 holes) with corresponding screws, ss., headless compression screws 2.7mm, self-tapping, cannulated, length 10-40mm,titanium, headless compression screw 3.5mm self-tapping, cannulated, length 10- 50 mm, titanium, headless compression screw 4.5mm self-tapping, cannulated, length 10 60 mm, titanium., 1.5 mm cortical screws for fixation of small bones, low profile head, 8 to 16 mm length, star head, titanium *, 2.0 mm cortical screws for fixation of small bones, low profile head, 8 to 16 mm length, star head, titanium *, 2.4 mm cortical screws for fixation of small bones, low profile head, 8 to 16 mm length, star head, titanium *, radius intramedullary square nail set diameter 2.0mm to 4.0 mm and length 20 to 36mm, stainless steel., ulna intramedullary square nail set, diameter 2.0mm to 4.0 mm and length 20 to 36mm, stainless steel., 3.5mm reconstruction non- locking plate set 4 to 14 hole with 8 cortical screw, stainless steel, 3.5mm reconstruction locking plate set 4 to 12 holes with 4 cortical screw and 6 locking screw, stainless steel., 2.7mm reconstruction non locking plate set, 4 to 14 holes with 8 cortical screws, stainless steel., orthofix external fixator, size- l/m/s/es, ss, dynamic screw measuring 9mm, ilizarov ring fixator set for tibia: one set consisting of 10 half rings (120 mm to 220 mm), plus one 5/8 ring (120mm to 220mm), 10 ring connecting bolts, 12 threaded rods(100 mm to 400mm), eight 1.8mm ilizarov wires(trocar/bayonet tip), six olive wires, 30 slotted bolts (centric/eccentric/schanz screw holding), 120 full nuts, 10 washer, two male and two female posts(one to four holes), four schanz screw 4.5mm/5.0mm, two male hinge and two female hinge. instrumentation to be provided along with the set must