Tender For supply of places , replacing wornout runner base and installing a new runner base of cane carrier and baggage elevator and r b c , replacing wornout runner with new one of cane carrier and baggage elevator and r b c , removing wornout angle iron and t iron of the cane carrier and reinstalling it by straightening the crooked part , removing the wornout part of the suit from different places and fitting it with new one , chevron grooving of new rollers of the mill , chevron grooving of old rollers of the mill , remove the wornout partition plates of the juice box above and below the juice heater by 10 or 12 mm ms plate and install it , installing ribs at the top and bottom partitions of the juice heater , repairing save all of qurdbody , removing old wornout gutters installed at various places and installing it with new gutters , remove the old wornout save all from pan and quard and install it with new one , reinstalling the new umbrella fitted inside the pan by making a new one and removing the old one , replacement ribbon arm of the mascute receiving crystallizer , making new separator of a centrifugal machine , removing the wornout truff of the hopper and installing it with new one , making and installing new separators for continuous centrifugal machines , removing the tubes of quad juice heater and dynamic juice heater and expanding them by installing new tubes and giving their hydraulic testing satisfactory of size 42 mm , removing the tubes of pan installing new tubes and expanding them and giving hydraulic tesing with satisfactory trial of size 96 mm , removing the wornout flue gas ducting of both the boilers and installing it with newone making from new or old plates , removing the wornout front and roof plate at boiler number 1 and 2 and installing with a new plate , removing the damaged boiler damper and installing a new one , making bagasse suit and installing. , replacement of juice over flow box of clarifier , making and installing bed of motor and pumps at various places as per requirement , replacement 6 inch dia cooling pipe of sulfur furnace , removing the monitor casing of a machine from old machine and installing it and giving its a trial , making amd replacing manholes at various places , making and replacing the enternals of cather of the pan. , making and replacing the new hood of cane cutter , removing the old bottom plate of the lowest compartment of the clarifier and placing a new plate on it after placing an angle trap as per the instructions and giving a satisfactory water trial , reinstalling the stirrer of the clarifier and giving a satisfactory trial , removing the shaft of a pug mill and replacing the old bushes on both sides and fitting new ones , removing and refitting the shaft of a brown sugar magma mixer and installing with new bush , reinstalling the trufff of connecting rod of the hopper , making and installing new catcher strainer , removing the old rail line of the trolley of the unloader and fitting the new rail line satisfactorily and doing water level , reinstalling the old rail line of the unloader s bridge and fitting it and checking water level etc , removal of old and weak channels of 3 inches to 10 inches diameter installed at various places and installation of new ones as per requirement , cutting and straightening old plates installed at various places as per requirement , removal of old and wornout scrubber installed on sulfur furnace and making and replacing with 8 or 10 mm plate and making all the connections , removing the trufff plate including support corroded shell and top cover plate of the top chamber of the clarifier and fitting the new plate and giving it s a water proof trial , re-installation alignment and //bid details 2 / 47 trial of hopper driving end , making and installing the top cover of the centrifugal machine , making an arm and installing it on the shaft of pug mill , making and installing scrubber and bottle jackets of sulfur furnace , making and install
Tender For auction sale of scrap from works / products used rail,scrap structural steel macalloy bar and nut,scrap weighing machine,scrap gi structure,scrapinductionmotor,scrap from works / products steel wire rope,scrap small tools ms,scrap from works / products miscellaneous steel scrap,scrap gi sheet,scrap rubber,scrap from works / products scrap aluminium ladder,scrap wooden,scrap packing straps
Tender For auction sale of depot ferrous scrap - scrap ferrous melting consisting of various cut pieces of lifting tackles,armature stands,mb caps,air dryer tank,bare stator frames,cut pieces of angles, frames, rings, angle pallets,jig and fixtures,side stopper,gear case assly, crain pillar,angle channels, fuel tank, compressor motor part, hosing bearing, turo charger part, speedometer, all pan, duct outlet and inlet scrap parts and other components of sorts and sizes etc.to pl-98050127 (cutting allowed for loading purpose)
Tender For auction sale of depot ferrous scrap - 98050114 scrap release all types of railway ferrous material consisting of s&t, p way, works and ohe items c & w items-suchas ms, gi, ci containing signalling units, rods, junction boxes, panels, ms gi structures, ladders, mast, rtu, cb, etc. andallother types of signaling items, gear case, the ground connection, ohe fitting, ms chains, heavy structure almirah/racks,rodsangle, top housing, road bar, glude joint, ground connection channel, pipes, lc material, ladders, jali, spring plank,pantographwith or without pneumatic motor, gate, door, brake cylinder, tie bar, fencing, trolley, ms machines etc., tmt barsrods, pulley,rib cage, point machines without motors, wagon body cut piece bogies side frame, machines, sleeper, ms sheet,various typessleeper part, tie bar, fencing bars, i-beam, damaged empty drums, light fittings, rail & rail pieces, ms wires, junklightweight/corroded material consist of toughened sheets, m.s./gi sheets, grease seal, drum, wire, parts of rolling shutter,lightweight cuttings, various damaged and rusty drums filled with coalter, dry paint, mud and dray fo if any of sort andsizes,g.i. buckets, steel buckets baskets, signal lamps, duct, vent pcs., fencing and pipes, wire mesh, stretcher, bicycle,pan,frames, electrical fittings, t.l. fittings, grill- jali, cabinet frames, rack ballast, rusted body and parts of weighingmachine,electronic/electrical material, small rods angle, battery boxes, tool boxes, shovel, rail door handles, main door, footplate,step plates, bench pipes, typewriter g.i. pipes, trolleys, water tank bond, location box with or without their componentandwiring fittings, trolly, different type of ohe bonds of rail and other various ms fabricated structures, break load rings,pins,screw, bolts, spikes, keys, loco parts, stay rods, sleeve for centre pivot, pantograph parts, palm pull rods, lever, axleboxhousings, air motor, springs of pantograph, connecting rods, and other rods, rear cover of axle box housing, etc. longerhanger,spare parts of spt machine, pipe fittings, end shield covers, break beam hangers, brake shoe, vertical lever, suspensionlevers,compressor spares, tension rods bushes, dash pots, collars, vehicle spares, ci items consisting ofrusty and dustydrainage pipe, valve, meter, brake block, pulley, motors body, pipes, plates, d.v, vacuum cylinder chamber, pigirons pieces,signaling box ohe fittings, steel furniture consisting of chairs, tables, g.i. separation sheet, chair , stretcher, beds,ms rack,almira, other types of steel furniture of sorts and sizes, broken, damaged with or without wood, cushions, plastic,mica, foamseat attachment, parts brake liner, thrust bearing, spring, yoke, insulation block hangers, slides, locking rods, partsof pointmachine, a b cover, break head, cylinder head, pcs. of break beam, protective tubes, and other p-way fittings, coupler,knuckles,cp top/bottom, pu pad, narrow/wide jaw adapter, released bulk head components, wagon doors, cutting plate, andassorted cutpieces thereof, fabricated from irsm 44, etc. brake cylinder, cs & ci if any. valve, broken pcs. of bearings, inner and outer raceof bearings, spares of break valve, trolley wheels, clamps, bmbc parts, pump shafts, impellers, tension device parts, fanarmatures, chain sling, rev. centre, hooks, spares of trucks, accessories of transformer, fish plates, hooks, silentblocks, cutpieces of plates, doors, angles, etc., fasteners such as bolts, nuts, and other related misc, etc., with or without, rail,of sorts andsizes with or without parts, fittings, and minor non-ferrous attachments, unserviceable. if any non-ferrous material is found willnot be delivered and retained by the custodian. minor/negligible nf attachment may be allowed. excluding items -rubber/wooden /plastic/ material and shed.
Tender For auction sale of depot ferrous scrap - 98050114 scrap release all types of railway ferrous material consisting of s&t, p way, works and ohe items c & w items- suchas ms, gi, ci containing signalling units, rods, junction boxes, panels, ms gi structures, ladders, mast, rtu, cb, etc. and allother types of signaling items, gear case, the ground connection, ohe fitting, ms chains, heavy structure almirah/racks, rodsangle, top housing, road bar, glude joint, ground connection channel, pipes, lc material, ladders, jali, spring plank, pantographwith or without pneumatic motor, gate, door, brake cylinder, tie bar, fencing, trolley, ms machines etc., tmt bars rods, pulley,rib cage, point machines without motors, wagon body cut piece bogies side frame, machines, sleeper, ms sheet, various typessleeper part, tie bar, fencing bars, i-beam, damaged empty drums, light fittings, rail & rail pieces, ms wires, junk lightweight/corroded material consist of toughened sheets, m.s./gi sheets, grease seal, drum, wire, parts of rolling shutter, lightweight cuttings, various damaged and rusty drums filled with coalter, dry paint, mud and dray fo if any of sort and sizes,g.i. buckets, steel buckets baskets, signal lamps, duct, vent pcs., fencing and pipes, wire mesh, stretcher, bicycle, pan,frames, electrical fittings, t.l. fittings, grill- jali, cabinet frames, rack ballast, rusted body and parts of weighing machine,electronic/electrical material, small rods angle, battery boxes, tool boxes, shovel, rail door handles, main door, foot plate,step plates, bench pipes, typewriter g.i. pipes, trolleys, water tank bond, location box with or without their component andwiring fittings, trolly, different type of ohe bonds of rail and other various ms fabricated structures, break load rings, pins,screw, bolts, spikes, keys, loco parts, stay rods, sleeve for centre pivot, pantograph parts, palm pull rods, lever, axle boxhousings, air motor, springs of pantograph, connecting rods, and other rods, rear cover of axle box housing, etc. longer hanger,spare parts of spt machine, pipe fittings, end shield covers, break beam hangers, brake shoe, vertical lever, suspension levers,compressor spares, tension rods bushes, dash pots, collars, vehicle spares, ci items consisting ofrusty and dusty drainage pipe, valve, meter, brake block, pulley, motors body, pipes, plates, d.v, vacuum cylinder chamber, pigirons pieces, signaling box ohe fittings, steel furniture consisting of chairs, tables, g.i. separation sheet, chair , stretcher, beds,ms rack, almira, other types of steel furniture of sorts and sizes, broken, damaged with or without wood, cushions, plastic,mica, foam seat attachment, parts brake liner, thrust bearing, spring, yoke, insulation block hangers, slides, locking rods, partsof point machine, a b cover, break head, cylinder head, pcs. of break beam, protective tubes, and other p-way fittings, coupler,knuckles, cp top/bottom, pu pad, narrow/wide jaw adapter, released bulk head components, wagon doors, cutting plate, andassorted cut pieces thereof, fabricated from irsm 44, etc. brake cylinder, cs & ci if any. valve, broken pcs. of bearings, inner and outer race of bearings, spares of break valve, trolley wheels, clamps, bmbc parts, pump shafts, impellers, tension device parts, fan armatures, chain sling, rev. centre, hooks, spares of trucks, accessories of transformer, fish plates, hooks, silentblocks, cut pieces of plates, doors, angles, etc., fasteners such as bolts, nuts, and other related misc, etc., with or without, rail,of sorts and sizes with or without parts, fittings, and minor non-ferrous attachments, unserviceable. if any non-ferrous material is found will not be delivered and retained by the custodian. minor/negligible nf attachment may be allowed. excluding items -rubber/wooden /plastic/ material and shed.
Tender For tender for supply of repair of vehicle 16c104372h : : - taking down defective priming pump , servicing and refixing of serviceable items , calibirataion and replace the following defective parts. , priming pump to filter hose , priming pump assy , fuel filter , m and l for dismantling of axle drive shaft of the vehicle with replacement of following parts. complete and connecting after lathe work of serviciable parts properly complete all as directed. , limited slip differencial lsd , axle shaft bearing , axle oil seal , gear oil , pasting , packing , cross bearing , dismantling complete radiator fan assy , cleaning the complete radiator fan and replacement of following new parts and fit to the base in original position and testing complete. , hose pipe with clip , repair of radiator fan motor 12 v dc , thermostat assy , m and l for dismantling of wheels 4 nos by jacking the vehicle opening of wheel hubs for cleaning and greasing complete with replacement of following parts. complete and connecting wheels including wheel allignment on computerized system and fixing wheels property all as directed. , bearing front wheel , bearing rear wheel , grease , repair of vacuum pump , tie rod assy , removing the clutch assy from engine and checking the serviceability of parts due to wear and tear and replacing the following parts with filling of gear oil fluid and fixing the clutch gear box in original position and testing complete. , cluch disc 260 dia bs4 , clutch cover 260 dia , general servicing of vehicle by draining out low viscosity engine oil , cleaning of oil pan pouring fresh engine oil and replacing of following parts reassembling , fixing in position testing complete. , oil filter , engine oil , coolent , air filter , misc , complete water servicing including spraying of oil , greasing in joints , bushes , bearings etc. cost and conveyance of all materials and including all labour charges etc complete.
Tender For supply of dimensions and design dtls held with 515 abw , dust cover mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , name plate charger unit mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , name plate battery ports mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , casing pin nylon cup mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , ss handles stainless steel dia 100x54mm as per sample held with 515 abw , battery charger meanwell input 90 to 260 vac output 13 point 5 vdc , smps meanwell input 90 to 260 vac output 12 vdc 35a , industrial led stego 22mm red indicator led panel mount indicator , charger output mg 02 2 pin mil grade connector , ac power input mg 02 3 pin mil grade connector , pop up attachment mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , slicing attachment mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , swing attachment mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , swivel attachment mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , target front support mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , fig point 11 target nylon polypropleyene mtrl plus corrugated sheet plus fig 11 target sticker 1140x480x6mm dimensions and design dtls held with 515 abw , fig point 12 target nylon polypropleyene mtrl plus corrugated sheet plus fig 12 target sticker 850x430x6mm dimensions and design dtls held with 515 abw , knobs with nuts ss m10x40 as per sample held with 515 abw , officer control unit by central control unit samsung 8 inchs android tablet tab a t355y android 6 point 0 above , sensor cable 8 pin male mil grade to sma connector 2 ft , illumination cable 5 pin male mil grade to 5 pin male mil grade connector 1ft , dc power cable 2 pin male mil grade to 2 pin male mil grade connector 1 ft , ac power cable 3 pin male ac connector to 3 pin male mil grade connector 1 point 5mtr , charging cable 2 pin male mil grade to 2 pin male mil grade connector 1mtr , ethernet cable for wifi station rj45 male to rj45 male ethernet cable 2 mtr , ethernet cable for repeater station rj45 male to rj45 male ethernet cable 2 mtr , ball stopper mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , barrel mild steel dimensions and design dtls held with 515 abw , bottom plate gun mild steel en8 dimensions and design dtls held with 515 abw , high torque motor clamp aluminum he 30 dimensions and design dtls held with 515 abw , long spacer al aluminum he 30 dimensions and design dtls held with 515 abw , short spacer al aluminum he 30 dimensions and design dtls held with 515 abw , main pcb spacer aluminum he 30 dimensions and design dtls held with 515 abw , main pcb panel aluminum he 30 dimensions and design dtls held with 515 abw , mechanism base mild steel en8 dimensions and design dtls held with 515 abw , nylon bush nylon m3 5 cm height 2 point 5cm inner dia dimensions and design dtls held with 515 abw , nylon cap nylon m3 1 point 9 cm dia dimensions and design dtls held with 515 abw , pan base left mild steel cold role mild steel sheet thickness 1 point 5 //bid details3 / 97mm dimensions and design dtls held with 515 abw , pan base right mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , pan base left cover mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and design dtls held with 515 abw , pan base right cover mild steel cold role mild steel sheet thickness 1 point 5 mm dimensions and