Latest laboratory equipment Tenders | Government laboratory equipment Tenders

CTN :45432698

15 Jun, 2026 NA

Bangalore - Karnataka

Tender For providing of customized amc/cmc for pre-owned products - laboratory equipment; imv india pvt limited; annual maintenance contract (amc); six-monthly; no

CTN :45415554

18 Jun, 2026 NA

Coimbatore - Tamil Nadu

Tender For purchase of equipment - purchase of equipment: dual pump nanofiber electrospinning unit, 1. high voltage power supply output: 0 40 kv, positive & negative polarity, digital control with current limiting and safety interlock2. syringe pump system dual syringe pumps, upgradeable to triaxial (3) or four (4) syringe configuration flow rate range: 0.001 20 ml/hr, compatible syringe size: 1 60 ml3. spinneret system stainless steel needles (18g 30g) capability for single, coaxial and triaxial electrospinning, multi-needle spinning provision4. collector system interchangeable flat plate and rotating drum collectors (different sizes), drum speed: 0 5000 rpm adjustable tip-to-collector distance: 5 30 cm5. environmental control chamber fully enclosed electrospinning chamber, temperature control: ambient 60 c humidity control: 20 80% rh6. control & automation touchscreen / pc-based operation, programmable process parameters real-time monitoring of voltage, flow rate, collector speed, temperature and humidity7. digital interface & data handling advanced digital interface for system control, high data storage capacity for experimental records data export through usb / ethernet8. safety features, fully grounded system door interlock for high-voltage safety emergency stop and overload protection9. accessories & support syringes, needles, grounding cables and collector substrates, on-site installation and user training, operation manual warranty: minimum 2 year

CTN :45416453

02 Jul, 2026 60.10 Lacs

Rohtak - Haryana

Tender For rate contract for 02 years (extendable) for purchase of biomedical waste sharps-blaster/disposable destroyer system and consumables for central store - sharp disposable destroyer system sharps balster sterilization unit(needle blaster) for treatemtn of biomedical waste category-iv make- safe environment solutions the unit is a desktop sized, simple plug & use type which converts the potentially hazardous sharps and syringes form blue bag category to black bag category at the touch of a button the unit is "ce approved". it is also approved by central pollution control board. it has also being recommended by w.h.o. the desk top solution is safe & environmentally friendly for the decontamination of sharps & other soft clinical wastes using non burn technology. machine is portable & can be installed in any part of the hospital without any extra utility requirement, operating on ordinary 230v ac. it effectively prevents second stick injuries which is a major concern as per who reports. user friendly & cost effective using very less power. sharp disposable destroyer consumables disposable canister, disposable 3 to 5 lit. metal canisters to collect the sharps or soft clinincal waste (needles, syringes, scalpel blades etc.) to be heated up to two and a half hours at temperature reaching 185'. canister should be lockable. , sharp disposable destroyer consumables disposable insert it is ldpe, pvc free inserts for sharp disposable destroyer unit. , sticky back paper label roll: thermal paper roll, 100 sticky back stickers per roll for sharp disposable destroyer unit. , active carbon filter active carbon filter for fume's entrapment, minimum 5 inch length, both ends open with suitable sealing gaskets.

CTN :45397326

08 Jun, 2026 9.75 Lacs

Bicholim - Goa

Tender For supply installation,testing and commissioning of laboratory equipment turbidity meter at 40mld wtp podocem, 5 7 mld wtp sankhalim and 15 mld wtp dabose under wd iii bicholim goa

CTN :45213596

08 Jun, 2026 NA

Kurnool - Andhra Pradesh

Tender For corrigendum : tender document for supply and installation of laboratory equipment in the department of electronics and communication engineering rayalaseema university college of engineering rayalaseema university kurnool

CTN :45213607

08 Jun, 2026 NA

Kurnool - Andhra Pradesh

Tender For corrigendum : tender document for supply and installation of laboratory equipment in the department of electronics and communication engineering rayalaseema university college of engineering rayalaseema university kurnool

CTN :45213642

08 Jun, 2026 NA

Kurnool - Andhra Pradesh

Tender For corrigendum : inviting tender document for supply and installation of laboratory equipment in the department of electronics and communication engineering rayalaseema university college of engineering rayalaseema university kurnool

CTN :45213644

08 Jun, 2026 NA

Kurnool - Andhra Pradesh

Tender For corrigendum : inviting tender document for supply and installation of laboratory equipment in the department of electronics & communication engineering rayalaseema university kurnool

CTN :45404122

09 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

CTN :45384476

11 Jun, 2026 NA

Dharmapuri - Tamil Nadu

Tender For purchase of equipments for mechanical department - purchase of equipments for mechanical department, tail stock assembly medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, working model of fuel supply system - petrol mpfi type petrol multi point fuel injection (mpfi) system for dismantling and assembly practice system type: non-working / cut-section model for study of internal construction construction: actual automotive components or equivalent training model mounted on frame includes throttle body (sectioned), fuel injectors, fuel rail, intake manifold includes fuel pump, fuel tank (dummy), fuel filter, pressure regulator includes ignition system components: ignition coil, spark plug, distributor (if applicable) ecu module (dummy/display type) with wiring layout representation all components cut-open, painted, and clearly labelled provision for manual demonstration of flow path and component interaction mounted on rigid ms powder-coated frame designed for repeated dismantling, assembly, and component identification, hydraulic cylinderbore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply: mounted on training base suitable for dismantling and inspection, hydraulic operated directional control valves (dcv) type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study, bearing with shaft assembly type: dismantling and assembly teaching unit shaft diameter: 30 mm shaft material: en8 steel bearings: deep groove ball bearing (6205 / 6206) housing: cast iron locking arrangement: circlips end covers mounting: bench-mounted / frame mounted unit, coupling unit using driving and driven shafts using plummer block bearing unit the plummer block housing material: cast iron (grade fg 200 or equivalent). type: sng or snl series (split-type housing). sealing: felt seals or v-ring seals (to demonstrate lubrication retention). lubrication: provided with a grease nipple at the top center for manual lubrication practice. the bearing type: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series). bore diameter: standard 25mm or 30 mm. shafting and coupling shaft material: ground carbon steel (en8 or en9) for high surface finish. coupling type: flexible coupling: to demonstrate the bearings ability to handle slight misalignment. rigid flange coupling: to demonstrate traditional direct connection. driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven)., 3d printing machine build volume(wxdxh) 256 x 256 x 256 mm shell enclosed (plastic & glass) hot end all-metal nozzle 0.4 mm stainless steel included max hot end temperature 300 nozzle diameter 0.4 mm (included) 0.2 mm, 0.6 mm, 0.8 mm build plate compatibility textured pei plate, cool plate, engineering plate, high temperature plate max build plate temperature 100 max speed of tool head 500 mm/s max acceleration of tool head 20 m/s supported filament pla, petg, tpu, pva, pet, abs, asa chamber monitoring camera low rate camera 1280 x 720/0.5fps time lapse supported filament run out sensor :yes control board fan closed loop control auxiliary part cooling fan closed loop control air filter activated carbon filter

Laboratory Equipment Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors