Latest lever pin Tenders | Government lever pin Tenders

CTN :43529952

20 Jan, 2026 NA

Jalpaiguri - West Bengal

Tender For supply of inch or 6 inch , pvc sunken box of size 4 inch x 8 inch , sheet steel enclosure for mcb spn db 8 way , thread seal tap 10 mtr long , street light 40 watt led in aluminium pdc housing , cable pvc frls copper conductor 1100 volt single core 4 sqmm 100 mtr per roll , cable pvc frls copper conductor 1100 volt single core 1 sqmm,100 mtr per roll , ph test kit with phenol red range 6. 8 to 8. 4 and 100 ml testing solution , phenol red solution for ph test in bottle of 500 ml , smoke detectore , sprincler single head , cotton waste , pvc saddle 25 mm , pvc saddle 20 mm , pvc saddle 8 mm , ms saddle 25 mm , ms saddle 20 mm , ms washer 3mm thick 8 or 10mm , ms washer 3mm thick 20 mm , split spin for ceiling fan , petroleum jelly , grease white , heating element for geyser 1. 5 kw clamp type , modolar switch 6 amps one modolar , on load manual changeover conforming to iec 60947-3 of range 200 amps 4 pole , on load manual changeover conforming to iec 60947-3 of range 250 amps 4 pole , industrial type recessed mounted 100 watt led light , led post top aluminium top reflector with ip 66 25 watt , nrv for geyser of capaciy 25 ltrs , screw brass 16mm to 19 mm , casing capping 20mm , brass nut bolt , pvc box with ss 5 amp , pvc box with ss 15 amp , selector switch , led fitting 1 x 10 w , led flood light 45 w , led flood light 200 w , compression type aluminium lugs suitable for 06 sqmm , compression type aluminium lugs suitable for 10 sqmm , mccb 250 amps 36 ka 4 pole , on load change over switch 200 amps 415 volt , on load change over switch 63 amps 415 volt , power unit 25 amps complete 4 modolar plate starter plug and socket , industrial cable with al conductor xlpe cable of size 3. 5 core x 35 sqmm , surge protection devices with 1 phase and 1 nutral 2 module 50 ka , surge protection devices with 3 phase and 1 nutral 4 module 50 ka , surge protection devices with 1 phase and 1 nutral 2 module 15 ka , surge protection devices with 3 phase and 1 nutral 4 module 15 ka , cable frls cable aluminium conductor 1100 volts capacity twin core x 6 sqmm , compression type aluminium lugs suitable for 120 sqmm , compression type aluminium lugs suitable for 35sqmm , led lamps 10 watt b-22 base , led tube light fitting 18 watt with batten , led tube light fitting 10 watt with batten , led highway flood light with high luminous efficiency input power 150 watt , led flood light 160 watt, 50 hz, 240 volt , mccbs 100 amps, 415 volts, 4 pole 16 ka , mccbs 125 amps, 4 pole 16 ka , modular white cover plate 6 module , multipurpose switch socket combination 5 pin flush type 15 or 16 amps , pvc frls cable copper 1. 5 sqmm 3 core 100 mtr per roll , pvc frls cable copper 2. 5 sqmm 3 core 100 mtr per roll , recess mounting ceiling type led 2 x 2 luminaire 45 watt , led flood light 60 watt, , led street light 90 watt , mnx type 3 pole power contractor mnx 12 , mnx type 3 pole power contractor mnx 22 , mnx type 3 pole power contractor mnx 25 , mnx type 3 pole power contractor mnx 32 , mnx type 3 pole power contractor mnx 40 , mnx type 3 pole power contractor mnx 50 , mnx type 3 pole power contractor mnx 70 , mnx type 3 pole power contractor mnx 80 , mnx type 3 pole power contractor mnx 95 , mcb sp 16 amps 10 ka,b curve , plug and socket db 32 amps 3 pin 4 module , cable join kit for 33kv earhted grade cable for indoor size 95 sqmm to 150 sqmm , cable join kit for 33kv earhted grade cable for outdoor size 300 to 400 sqmm , led facade light 120 watt , led pannel light 4 feet x 1 feet 36 or 40 watt , hose reel 63 mm dia , led aviation light 10 or 12 watt , dc power //bid details2 / 112pack for circuit breacker pannel with 24 v dc battery back up , flame proof switch 5 amp , delite led 18 watt with batten 6000k , led street light 70 or 72 watt, 240 volt, ip 66, 50hz , led street light 60 watt,240 volt, ip 66 , led street light 45 watt 240 volt,ip 66,50 hz , led flood light 120 watt , led flood light 100 watt , mccb 400 amps 36 ka 4 pole with spreader link , mcc

CTN :43529877

20 Jan, 2026 NA

Pune - Maharashtra

Tender For supply of gasket engine , spring plunger , throttle lever , pin master , filter assy , drum brake , bearing roller , lock plate , seal oil , hydf cylinder kit , fuel injector cummins , pump element , pump nozzle , fuel feed pump , roller bearing

CTN :43546915

22 Jan, 2026 NA

Faridkot - Punjab

Tender For tender for supply of bakelite sheet 6 inch x 6 inch duly wire cut for 3 switches , bakelite sheet 9 inch x 6 inch 1 switch and 1 socket 5 amp , bakelite sheet 9 inch x 6 inch 1 switch and 1 socket 15 amp , bakelite sheet 11 inch x 13 inch 06 switches and 1 socket 5 amp , machine screw 1 oblique 8 inch x 1 inch long brass , machine screw 1 oblique 8 inch x 3 oblique 2 inch long brass , machine screw 1 oblique 8 inch x 2 inch long brass , brass screw washer , insulation tape roll 20mm , casing caping 20mm , casing caping 25mm , casing caping 50mm , pvc conduit 20mm , pvc conduit 25mm , pvc clamp oblique shadle 25mm , screw star type black , pvc gitti 50mm , pvc gitti 38mm , ms sunken box suitable for 4 module switch socket board , ms sunken box suitable for 6 module switch socket board , ms sunken box suitable for 8 module switch socket board , ms sunken box suitable for 12 module switch socket board , round sheet oblique blanking plate , pvc flexible spring pipe 15mm , pvc flexible spring pipe 20mm , pvc flexible spring pipe 25mm , pvc connection with adaptor of 15mm dia 450mm length , aluminium conductor 2 core 10 sqmm 75mm length , ms pin fastner 12mm , bakelite plastic laminated hylem sheet , ss connection with adaptor of 15mm dia 450mm length

CTN :43547484

22 Jan, 2026 1.00 Crore

Baramulla - Jammu And Kashmir

Tender For supply of nos , ms screw 35 mm per pkt 100 nos , insulation tape 2 cm width 10 mtr long , mcb single pole 230v ac 50 hz 6 amps 10ka , mcb single pole 230v ac 50 hz 16 amps 10ka , mcb distribution boards in sheet metal enclosure 8 ways double door , residual current circuit breaker with over load and short circuit protection dp 32 amps , modular switch one way 16 amp 1 module m , modular socket 6a 2 3 pin combined 2 module , modular socket 6a 16a 2 3 pin combined 2 module , white cover plate with frame 3 module , white cover plate with frame 4 module , white cover plate with frame 1 module , metal flush box 3 module , metal flush box 4 module , metal flush box 1 module , compact street light 36 w , pvc casing caping pipe 25mmx16mm , pvc casing caping l bend 25mm , pvc casing caping elbow 25mm dia , pvc casing caping t 25mm for conduit pipe , pvc casing caping square box 4 inch x 4 inch , pvc body exhaust fan 250mm sweep with lowers , plastic body wall mounting fan 450mm sweep , storage electrical water heater geyser capacity 15 ltr with accessories , 3 layer ppr polypropylene random copolymer , 20mm elbow suitable for 20 mm dia pp r pipe , 20mm socket suitable for 20mm dia pp r pipes , 20mm equal tee suitable for 20mm dia pp r pipe , 20mm union suitable for 20mm pp r , gi reducer socket 15 20mm , gi reducer elbow 15 20 mm , pp r end plug 20mm , pp r pipe clamps suitable for 20mm piping , cp stop cock 20mm , cp bib cock 20mm with flange , pp r tank connector 20mm with check nut and washer , rotational moulded polyethylene water storage tank double layer , snow white colour european wc with s or p trap concealed , 600mm x 450mm looking mirror cabinet , over head shower without arm , soap dish for one soap , towel rail cp 750mm long with fixing clips complete , towel ring , toilet paper holder , health faucet with 1. 5 mtr tube and hook , cp pillar cock 20mm , pre fabricated man hole cover 6 ft x 4 ft , white lead safeda , thread cotton ball 100m long , 110 x 110mm nahani trap with jali , 110 mm dia upvc swr pipe single socketed , 110mm dia upvc single tee , 4 inch dia upvc bend , 110mm dia upvc swr pipe single socketed pipe , single tier sleeping bunks , single piece cushion made of 100 mm thick puf foam of density 40 kg , ms steel locker , office chair , office steel table , waste bin 60 ltr , looking mirror 1200x750x3. 5mm thick with plastic decorative frame , hanger stand 450mm length with 6 hangers , supply of centre table toughened glass 12mm thick , supply of 2 seater sofa the top shall be of upholstery with pu finish , anaerobic advance septic tank , 110 mm dia upvc swr single socketed pipe , 110 mm dia pvc l bow , 110 mm dia pvc socket , 110 mm dia pvc t equal , pvc pipe 3 inch 75mm dia 3 mtr , 75 mm dia pvc l bow , 75 mm dia pvc socket , 75 mm dia pvc t equal , pvc solution 250 ml , prefabricated gel earthing electrode of pipe in pipe technolog , gi pipe 100 mm dia medium grade , back fill compound , ms earth pit cover of size 30 cm x 30 cm with handle , aluminium strip 25 x3 mm x 9m , iron spikes 16 inch long , gi strip 32 x 6mm of length 3m , gi nipple 20 mm dia and 10 cm long , gi reducer socket 40 x20mm , lightning air terminal a copper tube 150 cm long x 25 mm , ms clamp 25 x 3mm with nut and bolt complete , gi wire 12 gauge , earth augur , pvc pipe 3m long 6 inch dia , user manual , tester set , gi pipe medium grade of 40mm dia 6 mtr long , gi pipe 40 mm bore 2m long , 50 mm bore gi pipe sleeve , crystaline conductive mixture , aluminimum straight edge 50mm squre 2mm thick 1800mm long , wooden flat gurmala , water leveling pipe //bid details2 / 111pvc 100 mtr , tasla iron 18 inch , shovel with wooden handle , hammer with wooden handle 5 kg , tape measuring metallic 30m , mason trowel karchi , axe picks with wooden handle , fawda with wooden handle , crowbar 5 feet long , pipe wrench 18 inch , aluminium spirit level 12 inch , hand gloves insulated with rubber isi mark , triple layered hdpe water tank of size 500 ltr

CTN :43547840

27 Jan, 2026 NA

Anuppur - Madhya Pradesh

Tender For tender for supply of ms flat 50x10 , ms flat 100x10 , ms flat 75x10 , ms flat 100x12 , plastic round bar 40mm , ms round bar 60mm , ms round bar 40mm , ms round bar 50mm , ms sheet 2mm , ms pipe dia 50 x 3 mm , ms electrode dia 4mm , ms electrode dia 3.15mm , m.s. hacksaw blade (1 sided) 300mm , m.s. wire spool mig welding (dia 0.8 mm) , hss tool bits miranda 7.5x100mm , hss tool bits miranda 1/2x1/2x6inch , hss tool flate patti miranda 5x25x150mm , cnc tool insert tnmg 160408 , cnc tool insert cnmg 120404/cnmg 431 , engine oil (5w30) , hydraulic oil castrol hyspin/heavy duty , pvc cu wire 1.5mm , pvc cu wire 2.5mm , pvc cu wire 4mm , al wire 1mm , flexible wire 1mm , one way switch 6amp , 5 pin socket 6amp , modular switch 6amp , modular switch 16amp , modular socket spin 6amp , modular socket spin 16amp , power switch 15amp , power socket 15amp , winding wire 35swg , winding wire 32swg , tube light rod 40watt , tube light choke 36watt , tube light led 36watt , fan regulator , modular fan regulator , cat 6 cable(external use) , network switch 24 port , network switch 8 port , antivirus , power cable for computer 1.5mm length , vga cable for computer 1.5mm length , keyboard , mouse

CTN :43532229

19 Jan, 2026 NA

Jamshedpur - Jharkhand

Tender For supply of 13 pin uic coupler plug assembly consist of 1.3 mtrs cable and polyamide house with uic plug on both ends as per rdso modification sheet no. rdso/pe/ms/c/ 0051-2011 rev.-2. note-uic plug as perclw drawing no . clw/e s/3/sk-4/0047/a similar to schaltbau part no. uic st 13 p eo d2 and polyamide conduit as per rdso specification rdso/pe/spec/a c-0138-2009 rev-2 or latest make: mli, schaltbau, pps international or similar. [ warranty period: 12 months after the date of delivery ]

CTN :43463693

21 Jan, 2026 4.64 Lacs

Thiruvananthapuram - Kerala

Tender For one panchayath one playground- thanniyam stadium in kallara grama panchayath in vamanapuram lac, thiruvananthapuram- supply and installation of outdoor gym and sports equipment - outdoor gym equipments, od252260/2025-2026 : horse rider - supply and installation of horse rider having the following specifications:dimensions: (l x w x h) 1140 x 400 x 1400 mm. main frame - 114 mm od b class gi pipe. foundationplate m.s. round plate of 250 mm & 8 mm thick. foundation cover cap - dome shape of pp / nylon /hdpe material. remaining frame is made by 48 mm od ?b? class gi pipe. seat frame ?is made by 48mm od ?b? class gi pipe. seat position must be horizontal to 110 -120 degree. link - made up of 48 mm od ?b? class g.i. pipe. angle between link and ground position is 10-20 degree. handle - 33 mm od ?b? class gi pipe. paddle vertical support - 60 mm od ?b? class gi pipe. handle frame- 42 mm od ?b? class gi pipe dually bending design. foot pipe - 33 mm od ?b? class gi pipe. support frame ? 10 mm thick ms flat is used. seat- dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material hdpe.bearing bush closing cap ? pp / nylon / hdpe material. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft.foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brand.bearing bushes - 60mm od seamless pipe. pin ? made of 25 mm m.s. bright bar. grips - high quality rubber 46 mm od. circlips ? a 24 circlips are used for assembly. coating - best quality of powder coating 60 to 70 micron. safety instructions and exercise chart - start &finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od252261/2025-2026 : back extension - supply and installation of back extension having the following specifications: dimensions: (l x w x h) 1060 x 730 x 990 mm. main frame - made from 88 mm od ?b?class g.i. pipe. foundation plate ? m.s. round plate of 250 mm & 8 mm thick. leg support - 42 mm od ?b? g.i pipe. seat rest pipe ? 42 mm od ?b? class g.i pipe. handle pipe ? 33 mm od ?b? class g.i pipe.footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 3 mm thick used to support it. footrest pipe ? 42 mm od ?b? class g.i pipe and 80 x 40 mm ms rectangular pipe. closing cap ?pp / nylon / hdpe material. seat ? 360 x 300 x 2 mm thick m.s. seat with corner fillet for safety. grips - high quality rubber 46 mm od. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od252262/2025-2026 : cross trainer (double) - supply and installation of double cross trainer having the following specifications: dimensions: (l x w x h) 2280 x 550 x 1650 mm. main frame- made of 88 mm od ?b? class gi pipe dually bending design. foundation plate ? m.s. round plate of 250 mm & 8 mm thick. paddle vertical support - 42 mm od ?b? class gi pipe. handle - 33 mm od ?b?class gi pipe dually bending design. leg movement frame ? 50 mm x 50 mm x 2 mm thick square pipe. footrest - cast iron 124 x296 x 5 mm thick and m.s. plat

CTN :43414033

15 Jan, 2026 10.09 Lacs

Thiruvananthapuram - Kerala

Tender For construction of madakkathara grama panchayath stadium in ollur lac, thrissur- supply and installation of outdoor gym equipment - open gym equipment, od263824/2025-2026 : chest press (double) - supply and installation of double chest press having the following specifications: dimensions: (l x w x h) 1955 x 710 x 1900 mm. main center pipe - ø 114 mm od ?b? class gi pipe. foundation plate ?m.s. round plate of ø 250mm & 8 mm thick. foundations cover cap- dome shape of pp / nylon / hdpe material. remaining frame - made up of ø 48 mm od ?b? class g.i. pipe. handle - made up of ø48mm od ?b? class g.i. pipe. link - made up of ø 48 mm od ?b? class g.i. pipe. seat & back rest ? 380 x 275 x 60 mm thick high-density polyethylene (hdpe) blow molded with m10 integrated wall thickness 3 to 4 mm. bearing bush closing cap?s? pp / nylon / hdpe material. handle must be connected with frame by 8 mm laser cutting ms profile. top closing cap ? dome shape made by pp / nylon / hdpe material.foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brands. pin ? made up of ø 25 mm m.s. bright bar pin. bearing bushes - ø 60 mm od seamless pipe. grips - high quality rubber ø 46 mm od. circlips?a 24 circlips are used for assembly. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be min m20 cc and design shall be approved by the engineer-in -charge before installation.), od263826/2025-2026: air walker - supply and installation of air walker having the following specifications: dimensions: (l x w x h) 1190 x 380 x 1244 mm. main frame- ø 88 mm od "b" class gi pipe dually bending design.foundation plate- m.s. round plate of ø 250 mm & 8 mm thick. paddle ø 42 mm od round gi pipe. handle - ø 33 mm od "b" class gi pipe. footrest - cast iron 124 x 296 x 5 mm thick and m.s. plate of 2 mm thick use to support it. top closing cap dome shape made by pp / nylon / hdpe material. closing cap's - pp / nylon / hdpe material. bracket - 8 mm thick laser profile is used to support paddle frame. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing- use is 6005 permanent lubricated reputed brands. pin's ø 25mm m.s. bright bar pin. circlips- a 24 circlips are used for assembly. bearing bushes -ø 60 mm od seamless pipe. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be min m20 cc and design shall be approved by the engineer-in -charge before installation.), od263830/2025-2026 : leg press (double) - specifications: dimensions: (l x w x h) = 1676 x 400 x1500mm. main frame - ø 114 mm od “b” class gi pipe. foundation plate – m.s. round plate of ø 250 mm & 8 mm thick. foundations cover cap - dome shape of pp / nylon / hdpe material. link - is ø 60 mm od “b” class gi pipe. seat frame - ø 42 mm od “b” class gi pipe. leg press back rest should be angled in 120 - 130 degree. footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 2 mm thick use to support it. seat & back rest – 380 x 275 x 60 mm thick high- density polyethylene (hdpe) blow molded with m

CTN :43530288

22 Jan, 2026 NA

Jaisalmer - Rajasthan

Tender For supply of spanner ring bihexagon cranked c c -spanners ring bihexagon cranked double e , spanner open jaw fixed double ended stee , s cotton thread 270 dtex x9 white 1000m , r polypropylene 3 strand h l og 18mm , solderinf iron electric 230volts 25w , rope cott h laid rot proofed undyed 8mm , handle files 115 mm , hammer sledge straight pein 3. 0 kg , soda ashtechnical , scissors 205 mm , hammer engineers ball pein 200 g , tefs 4m unit hammer 2 kg , fire hook 3. 5m , rope poly propylene 3 strand hawserlaid , pin tent wood mk 2 large 600 mm , machine weighing platform 100 kg d type , uc 4 6 men set slab wooden , uc 50 ms masala box ss 7 cntnr 500gm , charge fire ext dry powder 1 kg dry che , handle powrah wooden , spoon serving mk 2 , broom push 280 mm , gas lighter , suit case crew 660 mm with wheel ) /bid number: gem/2026/b/7096294 * /dated: 10-01-2026 & & / bid document1 / 27

CTN :43419959

15 Jan, 2026 200

Pune - Maharashtra

Tender For corrigendum : supply of protective glass z15 , lv1 tung 352-1210111 ms-158 bolt , lv3 tung gte pb6-450-230 hose perishable , lv3 tung gte 91156-9 21-00-10-000 gte assy 9e 56-9 , lv3 tung npn 245 ms 164 pump with electric motor , lv1 tung tu25-02-110461-85 ms pressure gauge receiver pd-it-1 5 mpa-k4 , lv1 tung nnk 7 cces 20 self recovery log , lv1 tung 569-1623130 ces-139 drain hose , lv1 tung tu 16522001-76 ms-30 safety fuse tv2 30v , k9 tung nbc lo-2-09-00-07-00-000 extension piece , z7 6220-000615 light unit head light , lv1 vt72b misc-1183-70-0131 inter connecting cable 15 m , lv1 vt-72b 1211-95-9120 hoses set , lv1 vt-72b bv9139999571 hose 725 13 4040 450 , lv1 vt-72b bv9139999574 hose 722-10-1010 1000 , lv1 vt-72b bv9139999581 hose 722-10-1010 600 , lv1 vt-72b 1181-919137 roller , lv1 vt-72b 1183-78-9076 pipe 1183-789076 , lv1 vt-72b 1183-78-9075 pipe 1183-78-9075 , lv1 vt-72b 1183-78-9015 pin distribution 3 1183-78-9015 , lv1 vt-72b 1183-69-9102 nut 1183-69-9102 , lv1 vt-72b 1181-33-9110 float valve 1181-33-9110 , lv1 vt-72b 1181-60-9127 pipe 1181-60-9127 , lv1 vt-72b 1183-699100 right bracket , lv1 vt-72b 1181-60-9118 pipe 1181-60-9118 , lv1 vt-72b 1181-33-9144 flange 118133-9144 , lv1 vt-72b 1183-78-9012 crane jib block , lv1 vt-72b 1183-69-9009 loading capacity indicator , lv1 vt-72b 1183-69-0151 short slide 1183-69-0151 , lv1 vt72b 1183-51-9104 arm with bush of 2nd right suspension , lv1 vt-72b 1183-51-9105 arm with bush of 6th right suspension , lv1 vt-72b 1181-33-9145 pipe coupling , lv1 vt-72b 1183-69-0146 pin 1183-690146 , lv1 vt-72b 1183-69-0147 pin 1183-69-0147 , lv1 vt-72b 1181-60-9112 pipe 1181-60-9112 , lv1 vt-72b 1181-33-9103 front right tank , lv1 vt-72b 1181-339106 equalization basin 1181-33-9106 , lv1 vt-72b 1183-76-0051 ring 1183-76-0051 , lv1 vt-72b 1181-459005 final drive major assy , lv1 vt-72b 1181-45-9105 output shaft , lv1 vt-72b 1181-57-0010 gear 1181-570010 , lv1 vt-72b 1183-76-0057 fuse 1183-76-0057 , lv1 vt-72b ssl-70-zssr bearing ssl 70-zssr , lv1 vt-72b 1181-45-9115 distribution oil 1181-45-9115 , lv1 vt72b 1181-45-9116 pipe 1181-45-9116 , lv1 vt-72b 118159-9208 carrier , lv1 vt-72b 1181-59-0080 piston 118159-0080 , lv1 vt-72b 1181-59-0092 bush 1181-59-0092 , lv1 vt-72b 1181-59-0041 bearing bush 1181-59-0041 , lv1 vt-72b 1181-59-0039 chain wheel 1181-59-0039 , lv1 vt-72b 1181-59-0089 planet wheel pin 1181-590089 , lv1 vt-72b 1181-57-0025 pin 1181-57-0025 , lv1 vt-72b 1181-57-0013 gear 1181-57-0013 , lv1 vt-72b 1181-57-0026 pin 1181-57-0026 , lv1 vt-72b 1181-570015 gear 1181-57-0015 , lv1 vt-72b 1181-57-0017 coupling 1181-57-0017 , lv1 vt-72b 1181-57-0019 gufero body 1181-57-0019 , lv1 vt-72b 1181-57-0028 washer 1181-57-0028 , lv1 vt-72b 1181-57-0011 gear idle 1181-57-0011 , lv1 vt-72b 1181-57-0024 shaft 1181-57-0024 , lv1 vt-72b 1181-57-0012 idle gear 118157-0012 , lv1 vt-72b 1181-59-0087 satellite 1181-590087 , lv1 vt-72b 1181-59-9001 auxiliary winch , lv1 vt-72b 1181-59-9111 ring 1181-59-9111 , lv1 vt-72b 1181-59-0255 pin 1181-59-0255 , lv1 vt-72b 1183-760049 pin 1183-76-0049 , lv1 vt-72b 1181-59-9119 guide bolt 1181-59-9119 , lv1 vt-72b csn-02-4630 bearing 6314 a tpx , lv1 vt-72b 1183-76-0007 flange 1183-760007 , lv1 vt-72b csn-02-4630 6008 bearing 6008 vs , lv1 vt-72b csn-02-4630 6215 bearing 6215 a , lv1 vt //bid details2 / 13672b csn-02-4630 bearing 6312 a tpx , lv1 vt-72b csn02-4630 6216 bearing 6216 tpx , lv1 vt-72b 1183-780065 bush 1183-78-0065 , lv1 vt-72b 0019-28-306-1 lower cone gear , lv1 vt-72b 1183-91-9116 suspension 2x5000kg , lv1 vt-72b 1183-91-9106 suspension rope , lv1 vt-72b csn-02-4705 bearing 22218 m tpx , lv1 vt-72b 1183-78-0064 bush 1183-780064 , lv1 vt-72b 1181-78-0046 nozzle 1181-78-0046 , lv1 vt-72b 1181-78-0434 neck m27x2 , lv1 vt-72b 118376-0009 piston 1183-76-0009 , lv1 vt-72b 1183-78-0055 pin 1183-78-0055 , lv1 vt-72b 1183-70-0039 temperature breaker lun3192-01-08 , lv1 vt-72b csn02-9280-9 20x16 ring 20x16 zmes nbr 1078 , lv1 vt-72b 1183-70-0101 pressure gauge

Lever Pin Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors