Latest lifting tackle repair Tenders | Government lifting tackle repair Tenders

State Government

CTN :40227801

27 May, 2025 49.58 Lacs

Gandhinagar - Gujarat

Tender For various routine/preventive and breakdown maintenance work on as and when require basis at chp-gtps - replacement of hammer rings for stage ii crusher , replacement of hammer rings for stage i crusher , replacement of screen plate / breaker plate/kick off plate of stage i and ii crushers , replacement of rotor of stage i crusher with disassembling of removed rotor and assembling of new/repaired rotor , replacement of drive end side bearing / pedestal of crusher rotor or complete gear coupling set of crusher or repositioning of dislocated rotor of crusher , replacement of non drive end side bearing/pedestal of crusher rotor or complete alignment of crusher motor with crusher rotor , replacement of broken hammer rings of stage i and ii crushers (stage i crusher up to 12 nos.of hammer rings and stage ii crusher up to 06 nos. of hammer rings at a time) , replacement of rail of rail table of wagon tipplers 1/2/3/4 (in one side full length) , replacement of clamping rubber pads of clamp for wagon of wagon tipplers , replacement of whole resting pads for wagon of side beam of wagon tipplers , replacement of spill plate roller of wagon tipplers , repairing/preparation/ fitting and replacement of hooks/rods/turn buckle, chain, sling rope ,spring assembly etc. of vibrating trays and crusher house trays , spillage control at various locations , miscellaneous cutting/welding work require at various locations , replacement of gearbox in conveyor no. 2a/b,11a/b,12a/b,13,14/15,16a/b,17a/b ,18a/b,drc/apron/rg/,wagon tipplers,stacker-reclaimer , replacement of gearbox in conveyor no.,5a/b,8a/b,10a/b,shuttle conveyor 1/2,belt feeder 1/2 ,roller screen, mrc 3/4/5,wobbler feeder ,dribble conveyor 1/2 , replacement of slow speed coupling set (two halves) of drive pulley , replacement of coupling bolts and rubber bushes of slow/high speed coupling(input/output coupling ) in conveyor no.2a/b,11a/b,12a/b,13,14/15,16a/b,17 a/b,18a/b,drc/apron/rg/,wagon tipplers,stacker-reclaimer , replacement of coupling bolts and rubber bushes of slow/high speed coupling(input/output coupling ) in conveyor no.,5a/b,8a/b,10a/b,shuttle conveyor 1/2,belt feeder 1/2 ,roller screen, mrc 3/4/5,wobbler feeder ,dribble conveyor 1/2 , replacement/removing/refitting of various size and type of fluid coupling , replacement or removing & refitting of any internal/bearing/input/ output oil seal of various size and type of gear box , overhauling of dismantles old/used gearbox in all respect with fitment of input and output coupling. , replacement of drive pulley , replacement of drive end side bearing of drive pulley or repositioning of dislocated drive pulley , replacement of non drive end side bearing/any side pedestal of conveyor drive/non drive pulley , alignment of motor/ gearbox/drive pulley including decouple/couple of coupling , nut bolt and drive system checking with replacement of broken nut bolt in all 04 wagon tipplers no.1/2/3/4 as per scope , lifting and releasing of gravity take up of any conveyor belt for locking and de locking of belts for other than belt replacement work , loosening and tightening of horizontal type screw take assembly of any conveyor belts for other than belt replacement work , work of dismantling and re erection of new/repaired apron pan from existing apron feeder of wagon tippler , repairing of upper/lower structure/cone plates of damaged/bend apron pan , replacement of carrying roller of apron feeder , replacement of worn out/ damaged ti roller and garland rollers. , replacement of worn out/ damaged impact rollers , replacement of worn out/ damaged return rollers , replacement of various worn out/ damaged ti roller stands , replacement of various worn out/ damaged impact roller stands , replacements of various worn out/ damaged return roller stands , replacement of various worn out skirt rubbers [10 m each] and skirt rubber with angle , preparation and replacement of guide rollers with bracket in place of worn out/ damaged guide rollers as

CTN :40232139

02 Jun, 2025 NA

Liluah - West Bengal

Tender For design, manufacture, supply and commissioning of air spring leakage test bench along wit h hydraulic lifting table for air spring of train 18 vande bharat (latest) & other lhb air springs as per spe cification/dimension mentioned in the uploaded annexure - a. [ warranty period: 30 months after the dat e of delivery ]

CTN :40232234

02 Jun, 2025 NA

Murshidabad - West Bengal

Tender For supply and commissioning of hydraulic table jack , scissor lift type-mobile, operation enviro nment-both (outdoor/indoor), power source-manual (heavy-duty hydraulic cylinder) , load capacity-200 kg s or above , lifting height-05 feet(1.524 meters) or above, length of platform size- 450 mm approx., width of platform size- 300 mm approx., portability-portable type (tyres for easy movement). [ warranty period : 30 months after the date of delivery ]

CTN :40024561

09 May, 2025 1.20 Lacs

Multi City - Telangana

Tender For corrigendum : procurement of hydraulic lifting table (gear box jacks) on specific make for area workshop, rg-i area

CTN :40199183

23 May, 2025 NA

Durgapur - West Bengal

Tender For supply of hydraulic scissor lifting table capacity 2 ton. (annexure attached) [ warranty period: 30 months after the date of delivery ]

State Government

CTN :40199881

16 May, 2025 NA

Nainital - Uttarakhand

Tender For tender for purchase of sports equipment and dress etc. of sports department, kumaun university nainital - sports equipment and dress etc., rate of football kit (t-shirt and shorts) with university name and number, rate of hockey kit (t-shirt and shorts) with university name and number, rate of basketball kit (dress) with university name and number, rate of volleyball kit (t-shirt and shorts) with university name and number, rate of athletics kit (dress) with university name and number, rate of cricket kit (sweater, trousers, t-shirt) with university name and number, rate of badminton kit (t-shirt and shorts) with university name and number, rate of football, rate of boxing kit with university name and number, rate of sepak takraw kit (t-shirt and short) with university name and number, rate of drop row ball (t-shirt and shorts) with university name and number, rate of table tennis (t-shirt and shorts) with university name and number, rate of lawntennis (t-shirt and shorts) with university name and number, rate of trekking and fitness (t-shirt and shorts) with university name and number, rate of yoga kit (t-shirt, shorts, tights fits) with university name and number, rate of taekwondo (kit) with university name and number, rate of karate (kit) with university name and number, rate of mini golf (kit) (t-shirt and shorts) with university name and number, rate of chess kit (t-shirt and shorts) with university name and number, rate of kabaddi kit with university name and number, rate of handball kit (t-shirt and shorts) with university name and number, rate of kho-kho (t-shirt and shorts) (kit) with university name and number, rate of woodball kit ((t-shirt and shorts) with university name and number, rate of football stockings with university name and number, rate of football (shin pads), rate of football goalkeeper knee cap, rate of football goalkeeper gloves, rate of hockey ball (match), rate of hockey stockings, rate of cricket batsman pads, rate of wicket keeping pads, rate of abdominal guard, rate of cricket bat (match), rate of cricket bat (practice), rate of basketball (match), rate of basketball (practice), rate of basketball net, rate of badminton shuttlecocks (plastic), rate of badminton shuttlecocks feather (match), rate of handball (man), rate of handball (women), rate of volleyball net, rate of towel, rate of table tennis ball (match), rate of table tennis net, rate of sepak takraw ball, rate of drop row ball, rate of lawn tennis ball, rate of crepe bandage, rate of shocks, rate of mini golf stick (putter), rate of mini golf ball, rate of woodball complete equipment set, rate of sepak takraw (net), rate of cricket ball (match), rate of cricket ball (practice), rate of cricket batting gloves, rate of keeping gloves, rate of cricket kitbag (big), rate of batting gloves inner, rate of badminton rackets (match), rate of badminton rackets (practice), rate of volleyball (match), rate of table tennis racket (match), rate of cross country kit, rate of judo kit, rate of qwan ki do kit, rate of wet.lif./ power lifting/ best phy.kit

Central Government/Public Sector

CTN :40176812

04 Jun, 2025 NA

Kanakapura - Karnataka

Tender For supply of austenitic steel coil 1.25x1250mm., as per drawing: rdso spec. no. c-k201, gra de x5crni1810 (304) table 1&2, heat treatment condition 2b as per table-5., packing instruct ion: stainless steel sheets, coils and plates:- (a) stainless steel (austenitic & ferritic st eel) coils. the coil shall be protected in reasonably good condition to withstand nor mal handling hazard during transit with the following provision as the barest minimu m: i) coil should be wrapped with a layer of water proof paper through out whole leng th. ii) coil should be wrapped with a layer of biodegradeable sheet. iii) outer & inner of coil should be wrapped with gi sheet. iv) side of the coil should be covered with card b oard sheet. v) after this whole coil should be wrapped with biodegradeable plastic sh eet of suitable thickness. vi) the inner edge of the coil should be protected by gi ring f ollowed by another iron ring. vii) outer edge of the coil should be wrapped with gi rin g. viii) coil should be securely strapped with minium 5 steel bands through the eyes of the coil and minium 3 steel bands on the circumference of the eye. ix) whole coil shoul d be mounted on wooden blocks for easy lifting/stacking. x) the sheets in coil form fo r thickness 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 100 0-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2 mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of coil 5.0 - 10 tonnes. (b) stainless steel (austenitic & ferritic steel plates/sheets) i) the sheet s/plates shall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate s hall be seprated with a layer of water proof paper, after this the whole bundle shoul d be wrapped with double layer of water proof paper and a biodegradeable plastic she et of suitable thickness. a metal protection in edges should also be provided. ii) all bu ndles shall have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop for every additional meter. the bundles shall also be provided with skid (wooden packing under neath) to facilitate handling. mechanical damange & corrosion during transit if any shall be at the cost of supplier. , proction procedure: covered in pi [ warranty period: 3 0 months after the date of delivery ]

Central Government/Public Sector

CTN :40151272

07 May, 2025 NA

Chennai - Tamil Nadu

Tender For supply of hydraulic scissor table:- lifting capacity : 800 kgs. platform size : 1220x 610 x 50 mm, minimum height :445 mm , maximum height :1500 and weight 170-200 kgs make : vanjax model vxlt 80 0/1500 or unique model: ust-800 (product catalogue to be attached for reference) [ warranty period: 3 0 months after the date of delivery ]

State Government

CTN :40044754

23 Apr, 2025 NA

Ranchi - Jharkhand

Tender For request proposal for supplying various equipment, chemicals, standard reference microbial cultures, glasswares/ plasticwares and general items in 13 numbers of district level water testing laboratories of jharkhand a-ranchi zone - refrigerator- ( 265 litre approx., double door ),make & model: branded ( is standard), analytical balance-( 4digit), weighing capacity of 220g, externally calibrated by nabl accredited lab/agency with calibration certificate, make & model: branded) ( is standard), ph meter-(measuring range ph0.0-14.0), make & model: branded ( is standard), hot plate with magnetic stirrer-(power: 2000 watt approx., operating volts: 230 15 volts a/c), stirring capacity : 50-1500 rpm, plate size : 1 ft *1.5ft (approx), make & model: branded ( is standard), bacteriological incubator-digital construction -double walled construction outer body made of mild steel powder coated & inner body made of stainless steel, insulation : glass woll insulation between two walls. inner size : 18" x 18" x 24", rating watts 750, no. of shelves 3, capacity 120 ltrs, temp range- 5 c - 60 c accuracy +/- 0.5 c, temp controlled by : controlled by pid micro process controller with dual display. selves : with g.i. wire mesh selves, door : 2 door inner acrylic door to view sample & outer metal door with air circulation motor with blower for uniform temperature throughout chamber. heater : special nichrome heater designed for long life & saving of power consuption. thermometer type : electronic with digital display. make & model : branded ( is standard), laminar air flow chamber(biosafety cabinet)-external dimensions (lxwxh) in inches and mm:40 x34.25 x56.7, (1020 x870x 1440) work area dimensions: 34.45 x24 x22.52 (857x610x572) material of construction: galvanised iron sheet with epoxy polyester thermosetting powder coating of 80 microns, 1.5mm thickness/stainless steel grade 304,1.2mm for ss modelsbody finish: glossy off white colour for gi powder coated table top: 1.2mm ss 304 sheet of matt finish pressed on 25mm solid nuwud board side glass: 6mm float glass encased in stainless steel channels front door: frameless gas spring loaded swinging type polycarbonate 6mm thickness wheels and levelling lugs: pu solid wheels with plated brackets and metallic powder coated design: front bottom loading pre-filters or completer work area with stainless steel including hepa grill cleanliness class: iso standard 14644-1- class 5 stages of filtration: a.pre-filters= 10 with an efficiency of 90 % washable hdpe media in frp pu coated frame b.mini pleat hepa filter encased aluminium frame with an efficiency of 99.995% motor blower assembly: variable speed mtor mounted on pu coated frp blowers with aluminium powder coated impellers velocity: 100 fpm at 6 from face of the filter noise level: less than 60db at 1 meter from the face of the equipmenthepa filter grill: stainless steel grills duly perforated and polished electrical specifications: a. switches and speed controller: microprocessor controlled feather touch switch panel b. fluorescent lighting: 18 watt. c. chokes for lighting: 18 watt d. ultraviolet lighting: 1.5 feet length g15t8, 15 watt power consumption: 250 watts lighting: greater than 800 lux power supply: 230v,50hz power supply, single phase 5 amperes power cord accessories: gas burner, gas/vacuum cock ( is standard), autoclave -vertical autoclave size 14" dia x 22" ht, rating in watts 3000, capacity of 52 ltrs complete s.s with foot lifting arrangement used for sterilization under saturated steam pressure at 15psi with double walled units with inner chamber made of thick stainless steel and outer chamber made of s.s.lid is made of thick gauge stainless steel with pressure gauge steam release valve, and safety valves. with foot lifting arrangement. with s.s. basketaccessories:1. digital temperature indicator cum controller with timer -1 no.2. water level cut off-1no.3. pressure cut off switch-1no. ( is standard), digit

CTN :40049441

23 Apr, 2025 NA

Krishnanagar - West Bengal

Tender For supplying of wooden items for the newly renovated suit rooms at new circuit house, nadia - supply, fitting & fixing including transportation charges of the king-size bed (6x7) with the following specifications: a) made from high-quality durable cp solid teak wood b) hydraulic lifting system for under-bed storage with drawers on both sides c) solid wood slats for optimal mattress support with a back support of 4ft height d) polished finish (pu) for refined look and safety standards e) includes two side tables of the same material for storage and aesthetic appeal , supply, fitting & fixing including transportation charges of cupboard with the following specifications: a) made of premium-quality teak wood (cp segun) b) dimensions: 3.0 ft width x 2.5 ft height x 1.50 ftlength c) multiple shelves and smooth, sturdy doors with quality hinges d) treated and polished wood for durability and finish e) stable structure for long-lasting use , supply, fitting & fixing including transportation charges of dressing table with the following specifications: a) crafted from high-quality cp solid teak wood (cp segun) b) dimensions: 6 ft length x 2.5 ft width x 1.25 ft length c) large mirror and multiple drawers for organized storage d) polished smooth finish for durability and refined look , supply, fitting & fixing including transportation charges of almirah with the following specifications: a) made from premium-quality teak wood (cp segun) b) dimensions: 6 ft height x 4.5 ft width x 1.75ft length c) multiple shelves and hanging rods for clothes, sturdy doors with secure locks d) treated and polished wood for finish and durability e) strong structure ensuring long-lasting stability , supply, fitting & fixing including transportation charges of tea table with the following specifications: a) made from high-quality teak wood (cp segun) b) dimensions: 2.5 ft height x 4.5 ft length x 1.75 ftwidth c) includes both closed and open storage zones d) treated and polished (pu) for durability and wear resistance , supply, fitting & fixing including transportation charges of tv showcase with the following specifications: a) crafted from premium cp solid teak wood b) dimensions: 2.5 ft height x 5.5 ft length x 1.75 ftwidth c) includes both open and closed storage zones d) polished (pu) wood finish for refined look and long-lasting performance , supply, fitting & fixing including transportation charges of cp solid teak wooden study table with chair with the following specifications: a) classic vintage design with detailed craftsmanship b) table dimensions: 48 inches width, 24 inches depth, 30 inches height c) hutch with open shelves and drawers for document organization d) paired with a sturdy wooden chair (cp segun)of 18 inches seat height

Lifting Tackle Repair Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

Central Government/Public Sector

Central Government/Public Sector

State Government