Tender For supply of assy cylinder block , assy cylinder head , gasket engine over hall , piston std , set of piston ring std , set of thrust washer , set of main bearing , con rod bearing , con rod bush , srdg ball bearing , locking plate , key-8x13 crank , cam shaft bush , propeller key camshaft , valve tappet in ex gaed , push rod inlet and exhaust , lock retainer valve spting , valve spring lock half , valve spring washer , gasket for support inj pump , rubber tube 140 injector , hose reducer for leak off inj , head water separator spin on , hose clamp , element air cleaner primary , element air cleaner softy , valve inlet and exhaust , valve oil seal , thermostat plastic assy , thermostat hose pipe with clamp , speedo meter sensor f14 wheel , banjo washer 10,12,14,17,19 , clutch sleeve cylinder assy. , clutch master cylinder assy. , diesel filter , oil filter body with filter , wiper motor reserve tank , timing cover oil seal front , crank shaft rear oil seal rear , diesel rubber pipe , jumble clip big medium , oil pipe rubber , rubber pipe hose , cam shaft tikki , oil jet , clutch plate assy , locking wire release brg , back light assy. rh ) /bid number: gem/2025/b/6949870 * /dated: 01-12-2025 & & / bid document1 / 38
Tender For purchase of equipments - purchase of equipment, bench top glass insitu airlift photo bioreactor1. vessel capacity: 3 liter borosilicate glass (working volume: two to three liters maximum), vessel hxd ratio 4:1 (400x100mm)2. head plate & bottom plate moc: ss 316l3. ports in top plate: ph sensor; dissolved oxygen (do) sensor; pressure sensor; air in and draft tube; air out; acid/base; sampling; and addition port.4. mixing method: ring sparger to create airlift circulation inside the reactor for uniform mixing and better aeration.5. holders for sensor /adapter / blind stoppers in head plate: ph sensor holder; media double inlet for acid/base dosing; air sparger - ring type for airlift application without stirring, air out with exhaust filter and open/close valve; pressure sensor holder; sampling pipe; blind stopper for un used port; unique suitable ss puncturing needles for sampling, air in, air out, inoculum, feed addition.6. ports in bottom plate with stand: port for temperature sensor; heating finger u-tube heat exchanger; drain.7. holders for sensor / adapter / blind stoppers in bottom plate: holder for temperature sensor, heating finger, u-tube heat exchanger.8. sensors: temperature, gel filled sterilizable ph sensor, & pressure sensor.9. controls and display: modular independent system of ph, temperature, pressure with touch screen graphical display & control; two set point control of ph with three-point buffer auto calibration; aeration by flow meter 0-5lpm with air pump; sterilization controls up to 121 without steam generator along with pressure safety mechanism by independent pressure sensor and digital display & control; automatic digital pressure safety and over temperature safety cutoff and alarm; upgradable control system for future prospective as cstr reactor & dissolved oxygen (do).10. measurement and control range: ph: 2-14; process temperature: 20 to 60 ; sterilization temperature: up to 121 ; and pressure up to 15 psi.11. fixed speed peristaltic pump: for acid/base dosing with teflon non spring head. (2 nos)12. cooling system: chiller cum circulator. chiller temperature range 4 to 40 , bath capacity 5l to cool down the reactor after sterilization and to work process temperature below ambient condition.13. illumination system: two illumination assembly with variable intensity control (1000-3000 lux) around the reactor with independent control switch for photobioreactor, or other application and easy detachable if not in use. 14. essential accessories : silicon tubing for acid/base addition (10m); air in and sampling (10m); water circulation (5m); air vent filters 0.2 micron sterilizable (6nos); and silicon septum (25nos)15. starter kit: spare silicon-o-rings for head plate, bottom plate (1no each), all other ports (5nos each), alen key.16. warranty: one year17. support (must): unconditional onsite technical support shall be provided as and when needed. the supplier must provide complete installation and hands-on demonstration of the equipment at the user site upon delivery.18. the vendor should have a registered presence in india with an authorized local service provider in tamil nadu.
Tender For bid to ras supply of ashok leyland spares--fg800900 filter element , fg801000 filter element safety , fg802600 filter element , fg802700 filter element safety , fhj02300 fuel filter fuel water seperator spin on main filter , fhj02400 fuel filter fuel water seperator spin on pre filter , p5105688 air filter inlet , fpm00400 oil sepaerator as ocv mahle
Tender For supply of cable glow plug assy 06 cyl,fuel filter cartridge,engine oil filter cartridge,air filter,seal kit intake manifold,seal kit exhaust,zinc anode,o ring 135x4,gasket inlet,o ring 17x3 53,o ring,o ring,o ring 22x3,exhaust hose id 90 mm,fuel water seperator,poly v belt l 1095 6 pk,tensioner poly v belt,glow plug std,o ring 46x3,o ring 42x4,o ring 49 2x3