Tender For supply of st030100641 return roller group with bracket,st030100642 spring disc small,st030100638 track bolt,st030100623 track nut,st030100632 plummer block assy - drive,st030100625 sprocket rim assembly,st030100643 sprocket bolt,st030100662 link pitch group master,st030100656 master pin set,st030100661 seal group for dwa,st030100660 seal group for ccsa,st030100633 plummer block assy - counter,st030100663 pinion,st030120022 ring hammers,st030120016 breaker plate with fasteners,st030120021 upper screen plate with fasteners,st030120020 lower screen plate with fasteners,st030120026 kick off plate with fasteners,st030120018 hopper liner set,st030120023 body liner set,st030120028 shaft seal - rotor body,st030120025 shaft seal - housing,st030120032 bearing housing wbyo brg,st030120027 deflector liner plate,st030120024 suspension bar with end plugs,st030120030 cage frame without liners,st030120031 locking assembly
Tender For supply of 2100001235 drill bit 5mm , 2100001236 drill bit 6mm , 2100001237 drill bit 7mm , 2100000153 grinder straight electric 100mm , 2200011250 hand drilling machine 13 mm , 2100000422 hand blower , 2100000653 allen key set 1by16 inch to 3by8 inch , 2100001540 steel measuring tape 5 mtrs , 2100001486 27 pcs 1by2 square drive 12 point socket , 2100001538 hacksaw frame 12 inch , 2100001605 screw driver size 18 inch , 2100001541 d e spanner 41x46mm , 2100000197 puller tool hydraulic bearing , 2100000411 chain pulley block 2 ton cap , 2100001045 electrician knife , 2100016827 cordless electric drill machine set , 2100000676 adjustable spanners 300mm long , 2100000595 de spanner set 6mm to 32mm , 2100000334 hand crimping tool , 2100000612 grease gun 5 kg bucket type , 2100000618 grease gun 10 kg bucket type , 2100001480 ring spanner set , 2100001176 steel tape 30 mtr length , 2100001090 dbl end spanner open jaw , 2100001047 de spanner 46x50 inch , 2100000941 single end spanner 55 mm , 2100000457 hyd crimping tool 16t
Tender For supply of fabricated atd bearing removal puller tool fitted on wooden frame of size 2 feet x 2 feet x 2.5 feet with ms angle screw threaded 18 inch. bolt of dia 40 to 50 mm to remove bearing. note: drawing to be got approved by consignee before commencement of work. [ warranty period: 30 months after the date of delivery ]
Tender For corrigendum : supply of double end ctrb mounting machine for mounting the ctrb simultaneously from both ends of wheel set, cap. 70t. as per technical specification given below : (1) hydraulic power pack : double speedmaximum working pressure of 450 kg/cm2 pump, pcm, level gauge, breather, strainer and pressure gauge etc will be installed in the power pack. (2) piston stroke of the cylinder : 450 mm (minimum) (3) capacity of the machine : 70 ton(4) speed (i) advance (idle stroke) 800 mm/min (+/-10%) (ii) installation : 110 mm/min (+/- 10%) (5) type of cylinder :hydraulic double acting (6) jack adjusting height from rail level to centre of installation tube : 360 to 560 mm (7) type of wheel lifting jack : supporting guide jack system with machine frame. ( 8) bearing mounting final pressure : 50+/-tons (will be held for 05 seconds) (9) type of pressure gauge : marking of pressure gauge will be dial in parallel measured in tones and kg/cm2 (10) time of both side mounting of bearing : not more than 2.5 minutes. make : sumanglam. technical specification attached. at annexure a. [ warranty period: 30 months after the date of delivery ]