Tender For corrigendum : ridf xxviii - lift irrigation projects in various padashekharams of wayanad district- procurement of submersible pumpsets, fittings, accessories, and related electrical works - procurement, installation, erection, testing, and commissioning of pumpsets and allied works at punchavayal, manikkuni, kolembetta, valiyavattam, and padiyeri pumphouses. - procurement, installation, erection, testing, and commissioning of pumpsets and allied works at punchavayal, manikkuni, kolembetta, valiyavattam, and padiyeri pumphouses., supply, installation, erection, testing, commissioning and fitting charges for all accessories of horizontally mounted submerged centrifugal non clog pump set of compact unitary mono-block submerged single/multi stage,volute type casing with suitable radial type impellers on common shaft for pump and motor ,anti friction bearing with life time greasing, protection features with sensors to monitor temperature,mechanical seal leakage ,etc.(the pump should be confirming to his/is standards).the moc of pump,casing-cast iron,impeller -ss cf8m,shaft-ss-316,suction strainer -ss and other as per is standard.the motor should be suitable for 3 phase,415v /-10%,50hz /5%,ac supply submersible motor having class f /h insulation, air filled and ip-68protection confirming to is 325 or latest standards suitable for day night operation.the pump discharge capacity of 230 cubic metre /hour against duty point head of 42 mtrs, working head range 18 - 47m, discharge range 136 - 57 lps ,speed 1450rpm(n) or nearer ,with 10meters of copper power cable and control cable, railing arrangement. the pump should be painted with three coats of suitable anti corrosive paint over priming coat. the electrical works for the pumpset should be completed as per kseb rules and regulations and the contractor is responsible for arranging premissions and certificates from the electrical inspectorate. the suction side of the pumpset should be provided with an additional iron grill for preventing foreign particles inside the inlet side of the pump casing., supply and erection of 60hp auto transformer starter (ats) with suitable incommer and contactors including 24 kvar capacitor with required indications ,metering and protections for single phasing ,overload, pump monitoring unit to protect from ingress, high temperature level etc enclosed in a closed panel board, supply and laying additional termination cable of 1.1kv 3.5 core 95sqmm aluminium conductor xlpe insulated ;steel armoured ug cable as per relevant is 7098 with support for cable, supply, installation, erection, testing, commissioning and fitting charges for all accessories of horizontzlly mounted submerged centrifugal non clog pump set of compact unitary mono-block submerged single/multi stage,volute type casing with suitable radial type impellers on common shaft for pump and motor ,anti friction bearing with life time greasing, protection features with sensors to monitor temperature,mechanical seal leakage ,etc.(the pump should be confirming to his/is standards).the moc of pump,casing-cast iron,impeller -ss cf8m,shaft-ss-316,suction strainer -ss and other as per is standard.the motor should be suitable for 3 phase,415v /-10%,50hz /5%,ac supply submersible motor having class f /h insulation, air filled and ip-68protection confirming to is 325 or latest standards suitable for day nightoperation.the pump discharge capacity of 188 cubic metre /hour against duty point head of 35 mtrs,working head range 16 - 42m, discharge range 102 - 42 lps ,speed 1450 rpm(n) or nearer ,with 10meters of copper power cable and control cable,railing arrangement. the pump should be painted with three coats of suitable anti corrosive paint over priming coat. the electrical works for the pumpset should be completed as per kseb rules and regulations and the contractor is responsible for arranging premissions and certificates from the electrical inspectorate. the suction side of the pumpset should be provided wi
Tender For supply of bearing block for tail end shaft complete with bearing housing and dust seal, without bearing suitable for bearing no 23140cck w33 for bec feeder breaker, part no 40061300 or equivalent , sprocket for tailend shaft for bec feeder breaker, part no 40061002 or equivalent , bearing block complete with bearing housing part no 40090800 or equivalent , cover for bearing block non drive end for bec feeder breaker, material en 24, part no 40091000 or equivalent , drive shaft assembly complete with sprockets, shaft, bearing, bearing block, distance piece etc. in assembled condition for bec feeder breaker, part no 40090001 or equivalent , tail end or return shaft assembly complete with sprockets, shaft, bearing, bearing block, distance piece etc. in assembled condition for bec feeder breaker, part no 40060000 or equivalent , bearing block for crusher roll non drive end with bearing housing and dust seal, without bearing suitable for bearing no 23044cck w33 for bec feeder breaker, part no 40041501 or equivalent , bearing block for crusher roll drive end with bearing housing and dust seal, without bearing suitable for bearing no 23044cck w33 for bec feeder breaker, part no 40041601 or equivalent , t head bolt for flight bar assembly of bec feeder breaker, part no 40050203 or equivalent drawing enclosed , nylock nut for bec feeder breaker, part no 40050204 or equivalent drawing enclosed , chain with flight bar assembly consisting of a chain 30x108x196 in mm links confirming to is din 22252 or equivalent nos., for bec feeder breaker, part no 40050000 or equivalent , chain connector suitable for chain 30x108 02 nos. for bec feeder breaker, part no 40050200 or equivalent , flight bar assembly for bec feeder breaker, part no 40050201 or equivalent , cover for crusher roll bearing block for bec feeder breaker, material en 24, part no 40041503 or equivalent , distance race or dust seal for return shaft assembly part no 40060000 of bec feeder breaker, part no 40061500 or equivalent drawing enclosed , distance race or dust seal for drive shaft assembly part no 40090001 of bec feeder breaker, part no 40091300 or equivalent drawing enclosed , tension head bow with tension bolt left for return shaft assembly part no 40060000 of bec feeder breaker, part no 40060200 or equivalent drawing enclosed , tension head bow with tension bolt right for return shaft assembly part no 40060000 of bec feeder breaker, part no 40060300 or equivalent drawing enclosed , key sprockets for return shaft assembly part no 40060000 of bec feeder breaker, part no 40062800 or equivalent drawing enclosed , labyrinth ring for crusher roll assembly part no 40041400 of bec feeder breaker, part no 40041502 or equivalent drawing enclosed
Tender For corrigendum : supply of hydraulic pump spares - eepeesafty_stud bolt with nut, eepeesafty_line shaft brg, eesafty_impeller, eesafty_link hyd pump u 1 2, eesafty_nylock nut hyd pump u 1 2, eesafty_rubber bush hyd pump u 1 2, eesafty_pin block hyd pump u 1 2, eesafty_retaining washer hyd pump u 1 2, eesafty_hx hd bolt hyd pump u 1 2, eesafty_hex hd cap screw hyd pump u 1 2, eepeesafty_allen set screw, eesafty_packing gland, eesafty_stud bolt with nut, eesafty_packing box bush, eepeesafty_hx hd cap screw, eepeesafty_hx hd bolt with nut, eesafty_line shaft brg, eesafty_disch case bearing, eesafty_hx hd bolt with nut, eesafty_bowl bush, eesafty_hx hd cap screw, eesafty_brg interbowl, eesafty_allen set screw
Tender For tender for supply of compr spring , gasket , retaining ring , orifice , wiring harness , gasket , piston , shpport shim input , bush , bush , bush , i clutch disc , gasket , thrust washer , pressure switch , sealing washer , sealing ring , retaining ring , snap ring , snap ring , o ring , o ring , piston ring , o ring , o ring , o ring , shaft seal , sealing ring , sealing ring , sealing washer , sealing ring , ax sf align brg , sf align bearing , washer a 3point00 , bush , cup spring , piston ring , shaft seal , roller brg , gasket , gasket , o clutch disc , o clutch disc , bush , gasket , gasket , gasket , bearing bush