Tender For auction sale of depot ferrous scrap - scrap ms melting consisting of buffer plunger with or without spindle, buffer socket, brake beam and truss bar, nut-bolt, rivets, pin, bush, small die, inner race, outer race, suspention strip, washer, door hinges, door roster, ff or rf, hb wheel, side bearer plate, yoke plate, bottom plate, ,sbs plate, anchor plate, hb lever, be lever, bc link, empty axle box, axle box cover, axle box housing, foot step, briddle bar, striker casting, back stopper, empty load box, main hole cover, shackle, shackle pin, screw coupling, bearing long shaft, cbc parts of coaches with undetchable nylon bush and other nylon items, shackle stone, coil spring, locking plate, shaft, operating handle, draw bar, broken coil spring up to four coil, front and rear plate, vertical support assly , main pin of cbc shank, manual uncoupling handle, wedge lock cbc parts of coaches, vertical supporting device for cbc, anti roll bar of lhb coaches, plunger, foot step, bb hanger, eq lever, bk shoe, striker casting, brake shoe head, bk.shoe key, silent block yoke pin support plate, lashing chain, buckle, roller, backing ring, spacer, distance ring, cone assembly and other parts of ctrb, wire supporting hook, protecting tube, silent block all type, l.s. beam, knuckle pin, knuckle plate, clamp, bearing pieces, silent block all type, sab complete and sab loose part, sab rod, and all type rod released from wagons loose and attached, control rod,coupler rod, small cut pieces of s.s., bracket, upper and lower part of control arm of lhb coaches and other ferrous melting category items, with or without minor undetachable non-ferrous attachment. [qty on approx basis].
Tender For supply and replacing of following items in sarawathi block lift johnson make: a) vertical member assy- lh c.o 2305 mm ht ms 1.2 mm primer finish - 130 type - 2 nos b)vertical member asy - rh c.o 2305mm ht ms 1.2 mm primer finish 130 type - 2 nos c)horizontal member top assy with nut holder assy ms primer finish 900mm pod co - 2 nos d)bottom member assy without fixing bracket with fastners 28-09-co-2-00-wofb-f - 4 nos e)main sill (co-900mm) - 4 nos f)auxillary sill(900mm -co) - 4 nos g)entrance horizontal support bracket 28-08-co-1-10-m for landing horizontal member fixing wall to sill - 4 nos h)grip expansion bolt with nut - m10 x 100 mm single wedge type - 4 nos i)entrance vertical support bracket - 8nos j)adjustable sillsupporting angle fixed bracket assy ( wall to sill edge 30 mm to 65mm) 28-08-co-2-10-01-0-090- 12 nos k)adjustable sill supporting angle moving braket assy( wall to sill edge 30 mm to 65mm)28-08-co -12 nos l)grip expansion bolt with nut -m12 x150 mm -single - 24 nos [ warranty period: 30 months after the date of delivery ]
Tender For design manufacture and supply of high tensile aar h type tight lock centre buffer coupler head with transition screw coupling and its associated components for fitment on broad gauge passenger coaches of indian railways as per rdso.specn.no. rdso/2009/cg-22, rev -01 one coupler set shall consists of the following 1.tight lock coupler head with transition screw coupling and its associated components 1 no rdso approved firm drgs. 2.balanced draft gear with pivot pin 1 no rdso approved firm drgs. 3.supporting device for coupler head with m20 fasteners 1 no rdso approved firm drgs. 4.manual uncoupling device with m12 fasteners 1 no rdso approved firm drgs. 5.rear carrier plate for draft gear with m16 fasteners 1 no rdso approved firm drgs. 6.front carrier plate for draft gear with m16 fasteners 1 no rdso approved firm drgs. special condition : 1. maintenance manual in soft copy and hard copy shall be supplied with item. 2.necessary test certificates as per rdso.specn.no. rdso/2009/cg-22 (rev -01) shall be supplied with item. 3. amd-01 of rev.03 or latest revision of specification rdso/2011/cg-03 referred in rdso/2009/cg-22, rev -01 or latest shall be followed.4. tenderer to submit rdso approved drawings at the time of quoting the tender. 5. packing condition: items are to be packed in two different boxes as given below. i. list of items to be in box-1 1. balanced draft gear with wedge block assembly & wedge block. 2. rear carrier plate 3. fornt carrier plate 4. fasteners for front and rear carrier plates. ii. list of items to be in box-2 1. coupler head and associated components. 2. main pivot pin. 3. supporting device for coupler head. 4. fasteners for supporting device. 5. manual coupling device 6. fasteners for manual uncoupling device. 7. split pinsfor carrier plate. 8. balance items, if any.. instructions for packing of fasteners. 1. box-1: item-4 2. box-2, item-4,6 & 7/ each to be packed and sealed separately in transparent polythene cover of minimum 200 microns with appropriate description labels kept inside for easy identification. stiffener plates must be supply as rdso letter no. no. mc/blb/cbc date: 01.11.2025. [ warranty period: 84 months after the date of delivery ]