Tender For general-republic day celebrations-2026-providing gi sheet pandal covered white cloth at municipal stadium - vidyanagar, kasaragod-general civil work
Tender For renovation of existing old toilet block at rear side of plb power house and providing gi sheet roofing and gi weld mesh at verandah portion.
Tender For corrigendum : supply of insulation and its accessories for orv sagar kanya - orv sagar kanya, w o no: 22022note :(i)for all types of insulation material given below, the following validcertificates to be submitted for technical evaluation along with thebidsa) manufacturers certificateb) type approval certificate(ii)sample to be submitted for sl.no. 110,120(iii) proof of supply certificate i.e., po of similar insulationmaterial supplied to other shipyards/industries, thermal insulation, 80 mm thick mineral wool insulation with adensity of 50 kg/m3, aluminium foil faced, thermal insulation, 30 mm thick mineral wool insulation with adensity of 50 kg/m3, aluminium foil faced, thermal and sound insulation, 100 mm thick mineral woolinsulation with a density of 50 kg/ m3, aluminium foil faced, thermal and sound insulation, 50 mm thick mineral wool insulation with a density of 50 kg/m3, aluminium foil faced, sound insulation, 100 mm thick mineral wool insulation with adensity of 50 kg/m3, aluminium foil faced and wire mesh, sound insulation, 100 mm thick mineral wool insulation with adensity of 100 kg/m3, aluminium foil faced and wire mesh, sound insulation, 50 mm thick mineral wool insulation with adensity of 100 kg/m3, aluminium foil faced and wire mesh, sound insulation, 50 mm thick mineral wool insulation with adensity of 50 kg/m3, aluminium foil faced and wire mesh, fire protection a-60, 90 mm thick mineral wool insulation with a density of 90 kg/m3, aluminium foil faced and wire mesh, sound-absorbing flooring-a 60, 60 mm thick mineral woolinsulation with a density of 54 kg/ m3, gi pins suitable for 100mm thick insulation, self-locking washers & closing caps. size of pin = 110mm length and 2mm dia., gi pins suitable for 50mm thick insulation, self-locking washers & closing caps. size of pin = 60mm length and 2 mm dia., gi sheet, 1mm thick, gi sheet perforated, 1mm thick
Tender For supply and installation of open gym equipments and construction of epdm flooring under open gym equipment in shahdara south zone, under mplads funds for various locations of parks in municipal corporation of delhi. - supply and installation of open gym equipments and construction of epdm flooring under open gym equipment in shahdara south zone, under mplads funds for various locations of parks in municipal corporation of delhi., seated puller /pull chair made from c class g.i pipe. dimensions: - 1900mm (length) x 740mm (width) x 1920mm. (height). safe area:- 1.2mtr x 3mtr. seated puller equipment made up of c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the center pipe is of 100nb made from c class g.i. pipe. bottom support is of m.s. round plate of dia 250 mm & 10mm thickness welded. all linkages are made up of 25nb c class g.i. pipe. the handle frame is of 32nb c class g.i. pipe. the seat frame is of 32nb c class g.i. pipe. to build structure bushes are used which are made from seamless pipe of 60mm o.d. and 5mm thickness as well as 60mm diameter solid bar bush used. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class. welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. foundation cover closing cap is made from injection moulded plastic lldpe / hdpe. the seats and back rests are fitted on the outer frames are made up of m.s. sheet of size 330 mm x 300 mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.closing caps are made up of from injection moulded plastic lldpe / hdpe.pins used of diameter 25mm and 17mm are made up from sae 8620 bright material. the bearings used are of 6205 2rs1 and 6203 2rs1 permanent lubricated sealed bearing of reputed brand.high tensile steel with galvanized nuts & bolts are used for assembly.thecirclips used for assembly are of a16. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)., cross trainer /elliptical exerciser dimensions: - 1320mm (length) x 600mm (width) x 1750mm. (height). safe area: - 1.77 x 1.2mtr. cross trainer equipment made from c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the main frame pipes are of 80nb c class g.i. pipe with single bend pipe with 250mm radius. the bottom support of m.s. round plate of dia 250 mm & 10mm thick. the handle frame is made up of 25nb c class g.i. pipe. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. to build structure bushes are used which are made from m.s. seamless pipe of 60mm od with 5 mm thickness. the footrests are made from injection moulded plastic lldpe / hdpe. closing caps are made up of injection moulded plastic lldpe / hdpe. pins used of diameter 35mm, 25mm, and 17mm are made up from sae 8620 bright .the bearings used are of 6007 2rs1 62052rs1 and 62032rs1 permanent lubricated sealed bearing of reputed brand. high tensile steel with galvanized nuts and bolts are used for assembly. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel
Tender For replacement of existing deteriorated corrugated ac & gi sheet with profile sheet at various location of power house 4x210mw at htps, cspgcl, korba west