Tender For btps - chp - replacement of engine cylinder head/liner and track repair work, repairs and reconditioning of radiators, silencers, oil coolers, cabin glasses, windows, electrical and ac repair work, repair and reconditioning of self -motors, alternators, fuel injection pump(fip) and turbo chargers, replacement/rearrangement of brake band shoe/liner, lift cylinder seals, tilt cylinder seals and track recoil cylinder seals of bd-355/bd-155 bull dozers as and when required in mm-iv sub division of mm/chp/btps during the fy 2026-27
Tender For tender for supply of canopy 8x8 , fuel filter fj 4a4 , clutch booster repair kit , repair kit for air pressure governor , coil assy ignition , mounting engine front , switch assy change over , cable assy speedometer , top deck assy grey , sensor water temperature , seal front oil 32x47x6 , head lamp assy , horn assy high , mirror assy inner rear view , gasket cyl head cover , belt water pump
Tender For supply of spark plug bc fs 410 , starter grip bc 410 , accecalarator cable bc fs 410 , accecalarator cable bc fs 400 , carburator bc fs 400 , starter grip bc 400 , fuel filter bc fs 400 , decompressed valve bc fs 400 , recoil pull starter rewind spring bc fs 400 , petrol tank bc fs 400 , tree pruner ht 75 stater grip , chain saw chain 20 inch , long nose plaier , 2t oil , tyre pressure guage , tyre air pump , face mask for chemical spray , tree pruner chain 12 inch , air filter bc fs 400 , tubeless tyre puncher repair kit
Tender For the detail of works includes:a. the tenderer shall carryout the following works during annual maintenance contract period along with the servicing of the diesel generator set.1. general checkup & preventive maintenance and to fill up preventive checkup schedule as follows:a) check lube oil level and conditioning of lube oil, top up/refill if required.b) the oil filters shall be replaced whenever oil is changed.c) the air filters shall be cleaned periodically with compressed air, check batteries and top up the distilled water if required.d) check functioning of changing alternator.e) engine safety viz. high water temperature gauge, oil temperature gauge and high speed gauge shall be checked for their functions and repaired/replaced if required.f) coolant level and conditioning of coolant shall be checked and refilled if required.g) check fan and alternator drive belts and tightened if required.h) the governor shall be checked and tuned for proper functioning.i) check for leaks if any and shall be rectified.j) check reports shall be submitted every month/every breakdown calls.2. checking and servicing of engine for smooth running, its unusual sound and color of smoke and exhaust and set it right in case of deviations.3. checking and repairing and leakage of fuel, lubricating oil and coolant.4. cleaning and changing of air filters as per requirement.5. setting of valves tappets whenever required.6. checking and repairing of accessories drive, turbo charger and crankshaft endplay whenever required.7. checking of alignment of engine & alternator as per requirement.8. checking of throttle control and its setting.9. checking of instrument panel including replacement as and when required.10. checking of rotating diodes assembly in brushless alternator including replacement as and when required.11. checking of wiring system and repairing/replacement as and when required.12. repair and maintenance of relays including contractors in control panel.13. checking of battery terminal and de-sulphating.14. diagnosis of faults in engine and alternator and its rectification.15. breakdown calls to be attended on priority within 6 hrs.16. providing spare avrs, self-starter and accessories, free of charge, if the repair/overhaul/replacement is expected to be taken in more than two days.17. checking/repair/adjustment/replacement/servicing shall be carried under annual maintenance contract except cost of component/parts to be replaced due to wear & tear.18. the firm should undertake to arrange genuine spares of the diesel engine, alternator and amf panel as and when required within two working days.19. the tenderer’s service engineer shall visit the site for attending the generator sets not less than twelve times during the contract period (minimum once in a month) and shall inspect the generator set thoroughly. each visit shall take place during 1st week of each month.20. the tenderer’s service engineer shall visit once in two month for checking of electrical side viz. alternator, amf control panel, if any.21. the engine shall be run on no load or at available load, and should be checked for any leakage and abnormal noise. if any such abnormality noticed shall be diagnosed and remedial action shall be taken.22. standard check list:a) replace minor parts (i.e hoses and filters etc) sub-assemblies as and when required.b) service engineers during the visit will report on the performance or any other abnormality and inform parts requirement. he shall also submit the report on work done and recommendations as well as spare parts required.c) attend emergency call on priority (usually same day). however, if the engineer is required or any particular date and time, it would be the responsibility of the customer to intimate the contractor in advance.d) major overhauling/ top overhauling / pt pump & injector calibration /replacement of major parts/ rewinding of alternator or repairs or breakdown of the diesel generator set are to be charge