Tender For corrigendum : tender for supply of epansion bellow dn100 , valve , temperature sensor , injector assembly , gasket , o ring an76 60c7 , gasket , shrink ring , cover , cover , floating bush , screw , limit switch bo , gasket , packing , ring , ring , o- ring , o-ring , locking plate , gasket , o ring an 77 50d7 , o ring 15204 viton 20209 , o ring 5589 viton 20312 , loctite , o ring dia 15 dia 204 , o ring dia 5 dia 589 , dowel bolt m24 100 , dirlled set bolt m33 180 steel 88 , drilled m33 nut , drilled m24 nut , plain machined washer , spherical bearing ge505w , link , fw level switch , gasket type 1 pn40 dn 4015 , gasket type 1 pn40 dn5015 , immersion heater , presuure gauge type a dn 100 , thermometer o-160 deg c pl 160 , epansion bellow assembly nd80 , epansion bellow assembly nd40 , lo flow switch , pressure gauge , sealing ring , he headed screw , locking plate , he headed screw , locking plate , cap nut , crancase pressure switch , set of gaskets for lub oil filter , o ring , pressure drop indicator-moatti filter , set of gasket -for moatti filter , diversion element , full flow element , gasket , gasket , o-ring , glanding , o-ring , oring , hose-fuel , hose-air , hose-oil , ruber compensating sleeve dn150 pn16 lf130 , gasket , gasket , gasket pn6 dn65 t 15 , loctite 648 , bulkhead connector 25 cts , o ring d821a7l 12cm , gasket , set of gasket-moatti fuel filter hyd motor , flat gasket pn 40dn65 t 15 , fuel clogging indicatior , sensor ref 19127sc , sensor ref 1950sc , switch for manual stop-ck-j265 , proimite detector mod 9984-2102 , breaker switch type zckj2 , hose , hose , gasket , o ring , set of o rings for p2-p4 by pass valve , gasket , gasket , gasket pn16dn100 type 01a , gasket , level switch fps-in11rww , o ring 05260 20313 , o ring , disc spring 315163175 , disc spring dia 25dia 12515 , disc spring 56 285 3 , main bolts , oring , o ring , o ring , set bolt m30 35 , temperature regulating pn40dn100 , pneumatic stop valve , pressure switch , thermometer 0-100 , tempsensor mbt4-s-130-m1815-ef3 , packing , gasket , guide bushing , actuator diaphram , diaphram hose clip , actuator diaphram wipe ring and seal kit , pressure gauge , thermostat element for naval opv , seal kit , pre heater coil , pressure gauge , set of spares for fuel oil filter
Tender For bid to ras supply of pipe compr air outlet kraz part no 123203552354 , pipe for lub oil inlet part no 100099390474 , pipe junction to pressure guage part no 123209390944 , air intake pipe for compressor part no 123209391385 , belt b-42 cogged part no 1034602211067 , flexible pipe injector of part no 123209390974 , gasket part no 123208520764 , pipe part no 123209390934 , pipe junction to pressure gauge part no 123209390944 , pipe pr relief valve to tank part no 100099391594 , main brg bush complete part no 623204300057 , connecting rod bearing bush complete part no 623284306047 , connecting rod bearing bush complete part no 623284306027 , main brg bush complete part no 623204300037 , main bearing bush complete part no 623204300017 , adaptor m16 - m26 male compra part no 123203552114 , pipe compr air oulet kraz part no 100099392614 , pipe between distributors part no 123209390934 , segmented gasket part no 123208530136 , charging valve part no 215619 , adaptar air intake 90 part no 123203552135 , bracket part no 123206250015 ) /bid number : gem/2026/b/7424945 * /dated: 08-04-2026 & & / bid document 1 / 21
Tender For the detail of works includes:a. the tenderer shall carryout the following works during annual maintenance contract period along with the servicing of the diesel generator set.1. general checkup & preventive maintenance and to fill up preventive checkup schedule as follows:a) check lube oil level and conditioning of lube oil, top up/refill if required.b) the oil filters shall be replaced whenever oil is changed.c) the air filters shall be cleaned periodically with compressed air, check batteries and top up the distilled water if required.d) check functioning of changing alternator.e) engine safety viz. high water temperaturegauge, oiltemperaturegauge and high speed gauge shall be checked for their functions and repaired/replaced if required.f) coolant level and conditioning of coolant shall be checked and refilled if required.g) check fan and alternator drive belts and tightened if required.h) the governor shall be checked and tuned for proper functioning.i) check for leaks if any and shall be rectified.j) check reports shall be submitted every month/every breakdown calls.2. checking and servicing of engine for smooth running, its unusual sound and color of smoke and exhaust and set it right in case of deviations.3. checking and repairing and leakage of fuel, lubricating oil and coolant.4. cleaning and changing of air filters as per requirement.5. setting of valves tappets whenever required.6. checking and repairing of accessories drive, turbo charger and crankshaft endplay whenever required.7. checking of alignment of engine & alternator as per requirement.8. checking of throttle control and its setting.9. checking of instrument panel including replacement as and when required.10. checking of rotating diodes assembly in brushless alternator including replacement as and when required.11. checking of wiring system and repairing/replacement as and when required.12. repair and maintenance of relays including contractors in control panel.13. checking of battery terminal and de-sulphating.14. diagnosis of faults in engine and alternator and its rectification.15. breakdown calls to be attended on priority within 6 hrs.16. providing spare avrs, self-starter and accessories, free of charge, if the repair/overhaul/replacement is expected to be taken in more than two days.17. checking/repair/adjustment/replacement/servicing shall be carried under annual maintenance contract except cost of component/parts to be replaced due to wear & tear.18. the firm should undertake to arrange genuine spares of the diesel engine, alternator and amf panel as and when required within two working days.19. the tenderer’s service engineer shall visit the site for attending the generator sets not less than twelve times during the contract period (minimum once in a month) and shall inspect the generator set thoroughly. each visit shall take place during 1st week of each month.20. the tenderer’s service engineer shall visit once in two month for checking of electrical side viz. alternator, amf control panel, if any.21. the engine shall be run on no load or at available load, and should be checked for any leakage and abnormal noise. if any such abnormality noticed shall be diagnosed and remedial action shall be taken.22. standard check list:a) replace minor parts (i.e hoses and filters etc) sub-assemblies as and when required.b) service engineers during the visit will report on the performance or any other abnormality and inform parts requirement. he shall also submit the report on work done and recommendations as well as spare parts required.c) attend emergency call on priority (usually same day). however, if the engineer is required or any particular date and time, it would be the responsibility of the customer to intimate the contractor in advance.d) major overhauling/ top overhauling / pt pump & injector calibration /replacement of major parts/ rewinding of alternator or repairs or breakdown of the diesel generator set are to be charge
Tender For supply of cummins engine spares c c - kit fuel filter and ring , valve shutoff , gaugetemperature , valve solenoid , minor service kit , gasket lub oil fil cover , gauge lub oil pressure , bushing , seal oil , gasket rkr lever housing , pump sea water , primer engine lubricating , gasket set , element assy , kit air cleaner , seal o ring