Tender For corrigendum : construction of transmission line - pcc poles supply and erection of pre-stressed cement concrete pole of suitable length with a given planting depth confirming to is-1678_1960_1978 below ground level in excavated pit of suitable dimensions complete in all respect as approved by engineer_in_charge at site pcc pole overall length 11 metre , planting depth 1.80 metre , w_l 400 kg pb csr 2020 item no 34.32(iii) , insulators supply and erection of insulators confirming to is_2544 and 5350 (test certificates of cpri) includes supply and erection of nuts bolts and other accessories whatsoever required at site for fixing it to the structure pole. the job is to be completed as approved by engineer_in_charge 11kv pin insulator with gi pin pb csr 2020 item no 34.35(i)(b) , stay sets supply and erection of stay set consisiting of 19_20mm dia.of suitable length gi stay rod duly threaded upto 300mm at one end and shaped on the other end ms plate size 30cm x 30cm x 6mm with 20mm dia hole drilled in the centre of the plate gi stay wire size 7_10 swg , gi thimble for stay binding , egg_strain insulator , ms elbow made out of 16mm plain sheet and a 20cm long piece of 50mm x 50mm x 6mm angle iron made to the shape as approved by engineer_in_charge. stay set complete shall be fixed to the pole by providing suitable size full clamps made out 50mm x 6mm size ms flat with required number of nut and bolts 16mm dia on one end and shall be embedded on the other end. the stay plate shall be covered with cement concrete having total volume of the concrete not less that 0.042cum. the job shall include excavation of pit and back filling and after pouring concrete with excavated soil etc. as approved_desired by the the engineer-incharge stay set consisiting of 19_20mm dia 2.4 metre long gi stay rod pb csr 2020 item no 34.35(ii)(b) , acsr conductor wolf 150mm2 , pole top brackets (galvanised) , v-shape cross arm 100x50mm , half clamp ms flat 50x5 , 11 kv polymeric disc insulators 70kn , danger plate , phase plate (set of 3) , barbed wire , earthing arrangement of 11kv poles , eye screw bolts 9inchx5_8 inch(galvanised) weight 0.483 kg. , nut and bolt ms off size , ms channel 100 x 50 x 6 - 2400 mm (galvanised) for h-pole , belting for h-pole 50 x 50 x 6mm . (galvanised) weight 9.90 kg , bracing for 4-pole 50 x 50 x 6mm . (galvanised) weight 14.49 kg , single tension fitting complete suitable for acsr wolf , pg clamp , full clamp ms flat 50x5 , ms angle 65x65x6 , erection charges
Tender For supply of diy lab accessories - raspberry pi 5 8gb ram with 64gb memory card and piduino official raspberry pi 5 27w usb power supply , arduino uno , 8 hdmi supported lcd display , key board , mouse , multi bit screw driver small , multi bit screw driver big , relay module , smps , plier , nose plier , wire striper cutter , hot air blower , digital multimeter , allen key set , 500 w hand drill machine , cordless hand drill machine , 670w angle grinder , pla fliament 1kg , jumper wires mm 40psc , jumper wires mf 40psc , jumper wires ff 40psc , desoldering wick , multi bit soldering iron , solder wire , soldering flux , desoldering pump , soldering iron stand , red and blue led , bread board 830 , dc jack male , potentio meter , electric tape , double side tape , hot glue gun and stick , different size drill bit set , 4 wood cutter wheel , 4 hand grinding wheel , awg high quality wire , different size zip ties , m3 bolt length , m4 bolt length , esp32 , 4 channel 5v relay module control , 5v dc power adapter , 6a 220v single pole ac switch and pvc board , 230 v square cooling fan , 5 w 220 v led bulb , holder and pvc board for led bulb , dual color wire for wiring , pir sensor , l293d 4channel dc motor driver shield for microcontrollers4 channel driver , pca9685 16 channel 12 bit pwm servo motor driver i2c module uno pic , x400 s400 drone kits included carbon fibre frame with landing gear motor prop and esc , pixhawk fc with power module saftey switch and buzzer original , xt 60 connector male-female pair , gnss receiver stand , vibration absorbing pad for fc , 200by300mm belcro belt , 6000 mah lipo battery , gnss receiver , 10 ch rc transmitter and receiver for drone , servo tester , lipo battery balance charger , duracell aa rechargeable battery , aa battery charger , sensor kit 40 in 1 bid number/ ( ( ) ): gem/2024/b/5694372 dated/* : 11-12-2024 bid document/ 1 1 / 45
Tender For supply of sprint 25 ft , 32 amp change over , clay plaster of peris , 2 5 black bundle copper , 1 5 mm black bundle copper , vinayal fix with sun board and iron fram , paint red blue and black , reflection board 3 into 2 and 2 into 1.5 ft , 16 watt surface light , 15 amp 2 socket 5 amp 3 socket 2 on off switch board , 5 amp switch with socket set , 15 amp 1 switch socket set , entity display with cabinet , safety control , pvc pipe 100 ft , 20 amp mch , boundary mic ahuja 301m , electric board 3 into 2 feet with mcb and socket , 6 mm 2 core wiren alluminium , mcb 32 amp 2 pole , electric panel assembly
Tender For custom bid for services - upgardation of nom tensile structur-fabrication work- fabrication of vertical member galvanised iron 150*150*1.6 mm box section frames for, entrance canopy size 140feet (07 nos weighting 500 kgs, fabrication of harizontal 100*50 mm 16mm gi box, frame, (a) size-400 feet (20nos) section size-600 feet (30nos) weigning-1200 kgs for ceeling, fabrication of vertical section member of galvanised iron 60*40*1.6mm for blocking the view & beaufication of venue - weighing 1900kgs, fabrication of circular ribs cross section supporled on the glavanised pole size +8+200mm for beautification of bar counted- weighing-450 kgs, fabrication of raise wooden metal fabrication table, acp panneling for entrance canopy, sheet roofing with sunglansed polycarbonite sheet, setting up of bar counter, circular counter for serving with services providing of shelves for storage of bottle, providing of under counter refrigerator providing/fixing of customises basin sink, plumbing work, providing/fixing of under counter storage shelves size-10ft 2.5ft*2feet+10nos, providing/fixing of l shape counter with wooden laminate 19mm ply size-5ft *2.5*2ft application of alluminium composite panneling for back drop of bar counter, providing & fixing vertical racks for display beautification of counter size (10ft 6ft) fixing of inverted glass holder, high raised stool, surface preparation application of one coated oxide primer on the fabricalled structure, providing & application of powder coated antirustblack coat colour then on existings & jr new frames, painting work, +, providing & application of wave theme paint coat on the vertical ribs strcture, electrical work, providing & fixing of inverted hanging antique lights for beautification to light up the venue space, providing & fixing of spot light for the internal fabricated false ceeling & bar counter, providing/fixing of profile led lights for beautification, electricalpoints, switch/sockets/modular box, with, wiring2.5 sqmm 2 core (including laying) 1.5sqmm*2 core*150*95, cable concealed conduit pipes, main junction box, electrical labour charge, providing/fixing of projection screen 10+6, feet, led neon name board for venue 4ft*1.5ft, transportation as actual loading/unloading alabour charges, design consultant fee
Tender For supply of led street light and its accessories - item description, led street light 90 w philips / surya/ havells/ bajaj, 32 mm dia(inner dia of pole arm)x 2 mtr long gi pipe (medium class)pole arm bracket for mounting of led street lighting fitting on pole including bending the pipe to required shape (90-105 degree),2 nos. 40mmx 3mm flat iron clamp withs nuts, bolt & washer, gi coating the flat iron with primer and finished paint as per relevant standard specifications., led driver (35 w), led driver (50 w), led driver (70 w), led driver (110 w), led driver (120 w), pcb 70 w, pcb 120 w, 1 core copper wire (1.5 sqmm), 1 core copper wire ( 1 sqmm), 2 core aluminium wire ( 2.5 sqmm), 2 core aluminium wire (6 sqmm), 2 core aluminium wire (10sqmm), switch (6 amp) with gang box, pvc tape, rope light, rope light connector, hand gloves(electrical work), plier, screw driver, tester
Tender For show jumping, dressage and tent pegging equipment for equestrian for 38th national games - wings(a) aluminium wings are durable and highly recommended for the new show jumping wings. the other option is wooden wings.(b) it may be noted that while wooden wings require frequent maintenance, such as painting and protection against moisture, they are easily repairable. on the other hand, aluminium is completely corrosion and maintenance-free. iron is again not an option; it s bulky & rust prone., poles (wooden material to be used), walls, gates, planks, ground box, flower box or brush box, ground fillers - all mix patterns matching with the wing & pole colour, cups 18mm depth(as per fie standards), safety cups (as per fie standards), liverpool (small & medium)(as per fie standards), red & white fiber flags red - 40white - 40, numbers markers, 1 to 14, alphabet marker sets of a-b, alphabet marker set of a-b-c, start (red & white), finish marking board (red & white), hand held stop watches, brase bell big, brase bell small, planters for arena decoration with real or artificial plants, measuring wheel, measuring tap 50mt open reel, liverpool medium, size 3 mt. 2 mt. in size, liverpool medium, medium, size 3 mt. 1 mt. in size, dressage arena boundary size20x60 mt., dressage arena marking, garden umbrella, table top bell, hand held bell (small), cardboard pegs, cardboard pegs, cardboard pegs, gallows as per efi, national federation guidelines, tent pegging sword, tent pegging lance, tent pegging lance